Home › Drivetrain › A750F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY › 2015.06–2020.08
RM27T0E _52 Drivetrain _053697 A750F AUTOMATIC TRANSMISSION / TRANSAXLE _0260761 AUTOMATIC TRANSMISSION ASSEMBLY A

A750F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 32000 1.INSTALL TORQUE CONVERTER ASSEMBLY

a.
C218127E01
2.81,0.457 2.963,0.638 0.153,0.181 10 A 2.557,0.686 2.736,0.873 0.180,0.187 10 *1 1.369,3.038 1.548,3.225 0.180,0.187 10 *1 2.994,1.796 3.173,1.982 0.180,0.187 10 *2 1.662,2.608 1.842,2.795 0.180,0.187 10 *2 2.752,1.528 2.853,1.883 2.853,1.883 2.944,1.883 false 2.268,1.355 2.416,0.774 2.416,0.774 2.513,0.774 false 1.204,1.704 1.508,2.703 1.508,2.703 1.605,2.703 false 0.912,2.119 1.216,3.118 1.216,3.118 1.313,3.118 false

Using a vernier caliper and straightedge, measure dimension A between the surface of the engine that contacts the transmission and the surface of the drive plate that contacts the torque converter.

Text in Illustration
*1 Engine Surface
*2 Drive Plate Surface


b.
C218122E01
1.108,0.022 1.314,0.205 0.206,0.182 10 *1 0.429,0.39 0.946,0.118 0.946,0.118 1.067,0.118 false 0.677,0.603 0.946,0.118 false

Align the matchmarks on the transmission case and torque converter, and then mesh the splines of the input shaft and turbine runner.

Text in Illustration
*1 Matchmark


c.
C218123E01
1.702,0.038 1.906,0.221 0.204,0.182 10 *1 0.436,0.384 1.498,0.141 1.498,0.141 1.62,0.141 false 1.097,1.556 1.498,0.141 false

Mesh the splines of the stator shaft and stator while turning the torque converter.

Text in Illustration
*1 Matchmark

HINT:

Turn the torque converter approximately 180°.



d.
C218124E01
1.305,0.039 1.493,0.217 0.188,0.178 10 *1 0.431,0.388 1.123,0.133 1.123,0.133 1.245,0.133 false 0.669,0.607 1.123,0.133 false

Turn the torque converter clutch and align the matchmarks on the torque converter and transmission case to fit the key of the oil pump drive gear into the slot on the torque converter.

Text in Illustration
*1 Matchmark

NOTICE:

Do not push on the torque converter when aligning the matchmarks.



e.
C218125E01
2.626,0.165 2.776,0.340 0.150,0.174 10 B

Using a vernier caliper and straightedge, measure dimension B shown in the illustration and check that B is more than A, which was measured in the first step.

Standard distance:

B = A + 1 mm (0.0394 in.) or more



Hide 33823 2.INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET

a.

Install the control cable bracket with the 2 bolts.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 36100 3.INSTALL TRANSFER ASSEMBLY

Hide 4.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY

C187504E02
3.008,1.003 1.954,1.003 false 0.951,0.909 1.176,1.117 0.225,0.207 10 *2 3.033,0.909 3.212,1.088 0.180,0.178 10 *1

a.

Apply clutch spline grease to the crankshaft surface that contacts the torque converter centerpiece.

Clutch spline grease:

Toyota Genuine Clutch Spline Grease or equivalent

Maximum grease amount:

Approximately 1 g (0.353 oz.)


Text in Illustration
*1 Torque Converter Centerpiece
*2 Crankshaft


b.
C232275

Confirm that the 2 knock pins are on the transmission contact surface of the engine block before transmission installation.


c.

Install the transmission with the 9 bolts.

Torque:
71 N*m (724 kgf*cm, 52 ft.*lbf)

NOTICE:
·

Insert the knock pins into the knock pin holes securely so that the end face of the transaxle assembly fits close against the engine assembly before tightening the bolts.

·

Do not use excess force to pry on the transmission assembly.




Hide 5.CONNECT WIRE HARNESS AND CONNECTOR

a.

Connect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer control side connector.

U170031

HINT:

Push up the lever until the claw of the transmission wire connector makes a connection sound.



b.

Attach the 7 harness clamps.


c.

Tilt up the automatic transmission.


Hide 32101A 6.INSTALL DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT

a.

Turn the crankshaft to gain access to the installation locations of the 6 torque converter setting bolts and install each bolt while holding the crankshaft pulley bolt with a wrench.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)

HINT:

If it is difficult to reach the setting bolts with the wrench, raise or lower the transmission jack until there is sufficient space for the wrench.


NOTICE:

Install the black bolt first, and then the 5 silver bolts.



Hide 12371 7.INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR

a.

Install the rear engine mounting insulator to the transmission with the 4 bolts.

Torque:
65 N*m (663 kgf*cm, 48 ft.*lbf)


Hide 51204 8.INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.

Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


b.

Install the frame crossmember with the 4 bolts and 4 nuts.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


Hide 51226A 9.INSTALL FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.

Install the front suspension member bracket LH and front suspension member bracket RH with the 8 bolts.

Torque:
33 N*m (337 kgf*cm, 24 ft.*lbf)


Hide 12156 10.INSTALL OIL PAN INSULATOR

a.

Install the oil pan insulator with the 2 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 28100 11.INSTALL STARTER ASSEMBLY

a.

b.

c.

Hide 32921 12.CONNECT NO. 1 INLET OIL COOLER TUBE AND NO. 1 OUTLET OIL COOLER TUBE

U170258E02
1.854,0.188 2,0.354 0.146,0.167 10 false B 3.667,0.615 3.844,0.802 0.177,0.188 10 true A 5.677,0.583 5.854,0.76 0.177,0.177 10 true A

a.

Temporarily install the ends of the 2 oil cooler tubes to each oil cooler tube union by hand.


b.

Install the 3 oil cooler tube clamps with the 3 bolts.

Torque:
for bolt A : 5.5 N*m (56 kgf*cm, 49 in.*lbf)
for bolt B : 14 N*m (143 kgf*cm, 10 ft.*lbf)


c.

Using a union nut wrench, tighten the inlet and outlet tubes.

Torque:
34 N*m (347 kgf*cm, 25 ft.*lbf)

NOTICE:

Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



Hide 33820B 13.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.

Connect the transmission control cable to the transmission control cable bracket with a new clip, and then connect the cable end to the control shaft lever with the nut.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 37110 14.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 15.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 36179 17.INSTALL LOWER TRANSFER CASE PROTECTOR

a.

Install the lower transfer case lower protector with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 18.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 51405A 26.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY