Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1761/61  Continuous Current to Compressor Motor  


DESCRIPTION

The signal from the suspension control ECU operates the AIR SUS relay and the height control compressor motor starts. The height control compressor motor operates until the targeted vehicle height is reached. Then the height control sensor sends the signal to the suspension control ECU, and stops the height control compressor motor.

DTC Code DTC Detection Condition Trouble Area
C1761/61 Either condition is met a total of 2 times or more with the ignition switch ON:
·

Power is continuously supplied to the height control compressor motor for 100 seconds.

·

Power is supplied to the height control compressor motor for 100 seconds or more within a 240 second period.


·

Air leakage from air tube or each valve

·

Clogging in air tube or each valve

·

AIR SUS relay (Suspension control relay)

·

Leveling solenoid valve (No. 2 height control valve)

·

Gate solenoid valve (No. 2 height control valve)

·

Exhaust valve (Height control compressor)

·

Compressor motor (Height control compressor)

·

Suspension control ECU



CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


HINT:

If DTC C1782/82 is output at the same time, perform troubleshooting for C1782/82 first (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782/82).


PROCEDURE

1.CUSTOMER PROBLEM ANALYSIS
a.

Ask the customer about the vehicle and usage conditions when the DTC was stored.

HINT:

DTC C1761/61 can be stored under unusual vehicle or usage conditions.

Points to confirm
·

Confirm if there were any foreign objects caught between the body and tires.

·

Confirm if the vehicle has been driven on an unpaved surface or with a wheel not contacting the ground.

·

Confirm if the vehicle has been raised with an excess load.

·

Confirm if the vehicle height mode has been continuously changed using the height control switch, causing the vehicle to raise and lower repeatedly.






NEXT

2.CHECK DTC
2.CHECK DTC

b.

Start the engine and wait for 4 minutes or more.


c.

Set the vehicle height to HI, wait until the vehicle height change is complete, and then return the vehicle height to normal.


d.

Check the DTC (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC C1761/61 is output A
DTC C1761/61 is not output B
DTC C1761/61 and other DTCs are output C



A

3.INSPECT AIR TUBE FOR AIR LEAK OR CLOG

B

END (C1761/61 WAS OUTPUT DUE TO UNUSUAL VEHICLE OR USAGE CONDITION)

C

3.INSPECT AIR TUBE FOR AIR LEAK OR CLOG
a.

Inspect the air tube for air leaks or clogs (See page Suspension>SUSPENSION CONTROL>SUSPENSION CONTROL SYSTEM (w/ Air Suspension)>PRECAUTION).

OK:

No air leaks or clogs are found in the air tube.




OK

4.INSPECT NO. 2 HEIGHT CONTROL VALVE

NG

REPAIR OR REPLACE AIR TUBE

4.INSPECT NO. 2 HEIGHT CONTROL VALVE
a.

Turn the ignition switch off.


b.

Remove the No. 2 height control valve (See page Suspension>SUSPENSION CONTROL>CONTROL VALVE ASSEMBLY>REMOVAL).


c.
C214512E18
2.563,0.479 2.396,0.479 2.396,0.479 2.052,1.115 false 1.313,1.177 0.948,1.625 0.948,1.625 0.948,1.74 false 1.76,1.208 1.802,1.896 1.802,1.896 1.927,1.896 false 0.063,0.083 0.365,0.292 0.302,0.208 10 false *a 0.802,1.792 1.115,1.979 0.313,0.188 10 false RH+ 1.99,1.802 2.198,1.99 0.208,0.188 10 false E 2.615,0.385 2.927,0.573 0.313,0.188 10 false LH+

Measure the resistance according to the values in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (LH+) - 2 (E) 15 to 25°C (59 to 77°F) 17.5 to 21.5 Ω
3 (RH+) - 2 (E) 15 to 25°C (59 to 77°F) 10 to 14 Ω


Text in Illustration
*a Component without harness connected
(No. 2 Height Control Valve)


d.

Check the leveling solenoid valve.

i.

Connect the positive (+) lead of the battery to terminal 3 (RH+) and the negative (-) lead to terminal 2 (E).


ii.

Check the operating sound of the No. 2. height control valve

OK:

It makes an operating sound (click).




e.

Check the gate solenoid valve.

i.

Connect the positive (+) lead of the battery to terminal 1 (LH+) and the negative (-) lead to terminal 2 (E).


ii.

Check the operating sound of the No. 2. height control valve.

OK:

It makes an operating sound (click).





OK

5.INSPECT HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)

NG

REPLACE NO. 2 HEIGHT CONTROL VALVE

5.INSPECT HEIGHT CONTROL COMPRESSOR (EXHAUST SOLENOID VALVE)

OK

6.INSPECT HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)

NG

REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY

6.INSPECT HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)

OK

7.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)

NG

REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY

7.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)

OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE SUSPENSION CONTROL RELAY (AIR SUS)