Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › 2015.06–2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1731/31  FR Damping Force Control Actuator Circuit  C1732/32  FL Damping Force Control Actuator Circuit  C1733/33  RR Damping Force Control Actuator Circuit  C1734/34  RL Damping Force Control Actuator Circuit  


DESCRIPTION

The absorber control actuator switches the damping force depending on the suspension control ECU signals.

DTC Code DTC Detection Condition Trouble Area
C1731/31 Either condition is met:
·

An actuator open-circuit signal is detected for at least 1 second when the actuator operates.

·

An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.


·

Harness or connector

·

Front absorber control actuator RH

·

Suspension control ECU


C1732/32 Either condition is met:
·

An actuator open-circuit signal is detected for at least 1 second when the actuator operates.

·

An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.


·

Harness or connector

·

Front absorber control actuator LH

·

Suspension control ECU


C1733/33 Either condition is met:
·

An actuator open-circuit signal is detected for at least 1 second when the actuator operates.

·

An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.


·

Harness or connector

·

Rear absorber control actuator RH (Rear shock absorber assembly)

·

Suspension control ECU


C1734/34 Either condition is met:
·

An actuator open-circuit signal is detected for at least 1 second when the actuator operates.

·

An actuator short-circuit signal is consecutively detected 8 times when the actuator operates.


·

Harness or connector

·

Rear absorber control actuator LH (Rear shock absorber assembly)

·

Suspension control ECU



WIRING DIAGRAM

C214503E08
5.479,8 7.094,8.208 1.615,0.208 10 false Suspension Control ECU 1.531,2.417 1.927,2.594 0.396,0.177 10 false FAL+ 1.542,2.792 1.938,2.969 0.396,0.177 10 false FAL- 1.542,3.198 1.938,3.375 0.396,0.177 10 false FBL+ 1.542,3.594 1.938,3.771 0.396,0.177 10 false FBL- 0.25,4.083 2.521,4.292 2.271,0.208 10 false Front Absorber Control Actuator LH 1.979,2.354 2.125,2.542 0.146,0.188 10 false 1 1.979,2.75 2.125,2.938 0.146,0.188 10 false 2 1.99,3.167 2.135,3.354 0.146,0.188 10 false 3 1.99,3.563 2.135,3.75 0.146,0.188 10 false 4 3.573,0.427 3.969,0.604 0.396,0.177 10 false FAR+ 3.573,0.813 3.969,0.99 0.396,0.177 10 false FAR- 3.573,1.208 3.969,1.385 0.396,0.177 10 false FBR+ 3.583,1.604 3.979,1.781 0.396,0.177 10 false FBR- 4.063,0.385 4.208,0.573 0.146,0.188 10 false 1 4.063,0.781 4.208,0.969 0.146,0.188 10 false 2 4.063,1.188 4.208,1.375 0.146,0.188 10 false 3 4.063,1.573 4.208,1.76 0.146,0.188 10 false 4 2.365,2.083 4.646,2.292 2.281,0.208 10 false Front Absorber Control Actuator RH 5.854,0.51 6.25,0.688 0.396,0.177 10 false FAR+ 5.854,0.906 6.25,1.083 0.396,0.177 10 false FAR- 5.854,1.302 6.25,1.479 0.396,0.177 10 false FBR+ 5.865,1.698 6.26,1.875 0.396,0.177 10 false FBR- 5.49,0.5 5.771,0.646 0.281,0.146 10 false A14 5.865,2.49 6.26,2.667 0.396,0.177 10 false FAL+ 5.865,2.885 6.26,3.063 0.396,0.177 10 false FAL- 5.865,3.292 6.26,3.469 0.396,0.177 10 false FBL+ 5.875,3.688 6.271,3.865 0.396,0.177 10 false FBL- 3.573,4.385 3.969,4.563 0.396,0.177 10 false RAR+ 3.573,4.792 3.969,4.969 0.396,0.177 10 false RAR- 3.573,5.188 3.969,5.365 0.396,0.177 10 false RBR+ 3.573,5.583 3.969,5.76 0.396,0.177 10 false RBR- 4.063,4.354 4.208,4.542 0.146,0.188 10 false 2 4.063,4.75 4.208,4.938 0.146,0.188 10 false 1 4.063,5.146 4.208,5.333 0.146,0.188 10 false 4 4.063,5.542 4.208,5.729 0.146,0.188 10 false 3 2.417,6.052 4.698,6.26 2.281,0.208 10 false Rear Absorber Control Actuator RH 5.49,6.448 5.833,6.615 0.344,0.167 10 false R19 5.854,4.469 6.25,4.646 0.396,0.177 10 false RAR+ 5.865,4.865 6.26,5.042 0.396,0.177 10 false RAR- 5.865,5.271 6.26,5.448 0.396,0.177 10 false RBR+ 5.865,5.667 6.26,5.844 0.396,0.177 10 false RBR- 0.313,8.063 2.583,8.271 2.271,0.208 10 false Rear Absorber Control Actuator LH 1.542,6.375 1.938,6.552 0.396,0.177 10 false RAL+ 1.552,6.76 1.948,6.938 0.396,0.177 10 false RAL- 1.552,7.156 1.948,7.333 0.396,0.177 10 false RBL+ 1.552,7.552 1.948,7.729 0.396,0.177 10 false RBL- 1.979,6.333 2.125,6.521 0.146,0.188 10 false 2 1.979,6.729 2.125,6.917 0.146,0.188 10 false 1 1.99,7.135 2.135,7.323 0.146,0.188 10 false 4 1.99,7.531 2.135,7.719 0.146,0.188 10 false 3 5.854,6.458 6.25,6.635 0.396,0.177 10 false RAL+ 5.865,6.854 6.26,7.031 0.396,0.177 10 false RAL- 5.865,7.25 6.26,7.427 0.396,0.177 10 false RBL+ 5.875,7.656 6.271,7.833 0.396,0.177 10 false RBL- 5.583,0.302 5.75,0.458 0.167,0.156 10 false 7 5.583,0.708 5.75,0.865 0.167,0.156 10 false 8 5.583,1.115 5.75,1.271 0.167,0.156 10 false 1 5.583,1.5 5.75,1.656 0.167,0.156 10 false 2 5.573,2.292 5.74,2.448 0.167,0.156 10 false 3 5.573,2.698 5.74,2.854 0.167,0.156 10 false 5 5.583,3.094 5.75,3.25 0.167,0.156 10 false 6 5.583,3.49 5.75,3.646 0.167,0.156 10 false 4 5.573,4.271 5.719,4.458 0.146,0.188 10 false 1 5.573,4.667 5.719,4.854 0.146,0.188 10 false 2 5.583,5.083 5.729,5.271 0.146,0.188 10 false 3 5.583,5.479 5.729,5.667 0.146,0.188 10 false 4 5.573,6.26 5.719,6.448 0.146,0.188 10 false 5 5.573,6.646 5.719,6.833 0.146,0.188 10 false 6 5.583,7.063 5.729,7.25 0.146,0.188 10 false 7 5.583,7.458 5.729,7.646 0.146,0.188 10 false 8 2.365,1.927 2.688,2.094 0.323,0.167 10 false A56 0.25,3.917 0.563,4.083 0.313,0.167 10 false A57 2.417,5.896 2.625,6.073 0.208,0.177 10 false S1 0.313,7.885 0.542,8.073 0.229,0.188 10 false S4 5.49,6.844 5.833,7.01 0.344,0.167 10 false R19 5.49,7.24 5.833,7.406 0.344,0.167 10 false R19 5.49,7.635 5.833,7.802 0.344,0.167 10 false R19 5.49,4.458 5.833,4.625 0.344,0.167 10 false R19 5.49,4.854 5.833,5.021 0.344,0.167 10 false R19 5.49,5.26 5.833,5.427 0.344,0.167 10 false R19 5.479,5.667 5.823,5.833 0.344,0.167 10 false R19 5.49,0.906 5.771,1.052 0.281,0.146 10 false A14 5.49,1.313 5.771,1.458 0.281,0.146 10 false A14 5.49,1.708 5.771,1.854 0.281,0.146 10 false A14 5.49,2.49 5.771,2.635 0.281,0.146 10 false A14 5.49,2.885 5.771,3.031 0.281,0.146 10 false A14 5.49,3.281 5.771,3.427 0.281,0.146 10 false A14 5.49,3.677 5.771,3.823 0.281,0.146 10 false A14

CAUTION / NOTICE / HINT

NOTICE:

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).


PROCEDURE

1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (DAMPER STEP)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / Air suspension / Active Test.

Air Suspension
Tester Display Test Part Control Range Diagnostic Note
Damper Step FR Changes damper step (Front RH) 1 to 17 step The shock absorber hardens as the damper step increases.
Damper Step FL Changes damper step (Front LH) 1 to 17 step The shock absorber hardens as the damper step increases.
Damper Step RR Changes damper step (Rear RH) 1 to 17 step The shock absorber hardens as the damper step increases.
Damper Step RL Changes damper step (Rear LH) 1 to 17 step The shock absorber hardens as the damper step increases.

OK:

The absorber control actuator operates.




OK

NG

2.INSPECT ABSORBER CONTROL ACTUATOR
2.INSPECT ABSORBER CONTROL ACTUATOR
a.

Turn the ignition switch off.


b.

Check the front absorber control actuator RH (when DTC C1731/31 is output).

i.

Disconnect the A56 actuator connector.


ii.
C179520E12
1.927,1.469 2.417,1.708 false 1.552,1.49 1.094,1.698 false 1.927,1.292 2.417,1.146 false 1.552,1.313 1.094,1.135 false 0.073,0 0.302,0.188 0.229,0.188 10 false *a 0.635,1.635 1.083,1.823 0.448,0.188 10 false FBR+ 2.458,1.625 2.979,1.813 0.521,0.188 10 false FBR- 0.625,1.021 1.073,1.208 0.448,0.188 10 false FAR+ 2.458,1.063 2.979,1.25 0.521,0.188 10 false FAR-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FAR+) - 2 (FAR-) Always 6.4 to 7.2 Ω
3 (FBR+) - 4 (FBR-) Always 6.4 to 7.2 Ω


Text in Illustration
*a Component without harness connected
(Front Absorber Control Actuator RH)



c.

Check the front absorber control actuator LH (when DTC C1732/32 is output).

i.

Disconnect the A57 actuator connector.


ii.
C179520E13
1.917,1.479 2.406,1.719 false 1.552,1.49 1.094,1.698 false 1.927,1.292 2.417,1.146 false 1.552,1.313 1.094,1.135 false 0.073,0 0.24,0.24 0.167,0.24 10 false *a 0.667,1.635 1.115,1.823 0.448,0.188 10 false FBL+ 2.448,1.646 2.969,1.833 0.521,0.188 10 false FBL- 0.656,1.01 1.104,1.198 0.448,0.188 10 false FAL+ 2.458,1.063 2.979,1.25 0.521,0.188 10 false FAL-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (FAL+) - 2 (FAL-) Always 6.4 to 7.2 Ω
3 (FBL+) - 4 (FBL-) Always 6.4 to 7.2 Ω


Text in Illustration
*a Component without harness connected
(Front Absorber Control Actuator LH)



d.

Check the rear absorber control actuator RH (when DTC C1733/33 is output).

i.

Disconnect the S1 actuator connector.


ii.
C179521E11
1.927,1.521 2.417,1.708 false 1.552,1.521 1.094,1.677 false 1.906,1.292 2.396,1.146 false 1.552,1.302 1.094,1.125 false 0.073,0 0.302,0.188 0.229,0.188 10 false *a 0.635,1.615 1.083,1.802 0.448,0.188 10 false RBR+ 2.458,1.635 2.979,1.823 0.521,0.188 10 false RBR- 0.615,1 1.063,1.188 0.448,0.188 10 false RAR+ 2.458,1.063 2.979,1.25 0.521,0.188 10 false RAR-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RAR-) - 2 (RAR+) Always 6.4 to 7.2 Ω
3 (RBR-) - 4 (RBR+) Always 6.4 to 7.2 Ω


Text in Illustration
*a Component without harness connected
(Rear Absorber Control Actuator RH)



e.

Check the rear absorber control actuator LH (when DTC C1734/34 is output).

i.

Disconnect the S4 actuator connector.


ii.
C179521E12
1.927,1.521 2.417,1.708 false 1.552,1.521 1.094,1.677 false 1.917,1.292 2.406,1.146 false 1.552,1.313 1.094,1.135 false 0.073,0 0.271,0.188 0.198,0.188 10 false *a 0.625,1.604 1.073,1.792 0.448,0.188 10 false RBL+ 2.458,1.635 2.979,1.823 0.521,0.188 10 false RBL- 0.604,1.031 1.052,1.219 0.448,0.188 10 false RAL+ 2.458,1.063 2.979,1.25 0.521,0.188 10 false RAL-

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (RAL-) - 2 (RAL+) Always 6.4 to 7.2 Ω
3 (RBL-) - 4 (RBL+) Always 6.4 to 7.2 Ω


Text in Illustration
*a Component without harness connected
(Rear Absorber Control Actuator LH)

Result
Result Proceed to
OK A
NG (Front absorber control actuator RH) B
NG (Front absorber control actuator LH) C
NG (Rear absorber control actuator RH) D
NG (Rear absorber control actuator LH) E




A

3.CHECK HARNESS AND CONNECTOR (ABSORBER CONTROL ACTUATOR - SUSPENSION CONTROL ECU)

B

REPLACE FRONT ABSORBER CONTROL ACTUATOR RH

C

REPLACE FRONT ABSORBER CONTROL ACTUATOR LH

D

REPLACE REAR SHOCK ABSORBER ASSEMBLY RH

E

REPLACE REAR SHOCK ABSORBER ASSEMBLY LH

3.CHECK HARNESS AND CONNECTOR (ABSORBER CONTROL ACTUATOR - SUSPENSION CONTROL ECU)
a.

Check the front side absorber control actuator.

i.

Disconnect the A56 and/or A57 front absorber control actuator connector.


ii.

Disconnect the A14 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Front RH (for DTC C1731/31)
Tester Connection Condition Specified Condition
A56-1 (FAR+) - A14-7 (FAR+) Always Below 1 Ω
A56-2 (FAR-) - A14-8 (FAR-) Always Below 1 Ω
A56-3 (FBR+) - A14-1 (FBR+) Always Below 1 Ω
A56-4 (FBR-) - A14-2 (FBR-) Always Below 1 Ω
A56-1 (FAR+) - Body ground Always 10 kΩ or higher
A56-2 (FAR-) - Body ground Always 10 kΩ or higher
A56-3 (FBR+) - Body ground Always 10 kΩ or higher
A56-4 (FBR-) - Body ground Always 10 kΩ or higher

for Front LH (for DTC C1732/32)
Tester Connection Condition Specified Condition
A57-1 (FAL+) - A14-3 (FAL+) Always Below 1 Ω
A57-2 (FAL-) - A14-5 (FAL-) Always Below 1 Ω
A57-3 (FBL+) - A14-6 (FBL+) Always Below 1 Ω
A57-4 (FBL-) - A14-4 (FBL-) Always Below 1 Ω
A57-1 (FAL+) - Body ground Always 10 kΩ or higher
A57-2 (FAL-) - Body ground Always 10 kΩ or higher
A57-3 (FBL+) - Body ground Always 10 kΩ or higher
A57-4 (FBL-) - Body ground Always 10 kΩ or higher




b.

Check the rear side absorber control actuator.

i.

Disconnect the S1 and/or S4 rear absorber control actuator connector.


ii.

Disconnect the R19 suspension control ECU connector.


iii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for Rear RH (for DTC C1733/33)
Tester Connection Condition Specified Condition
S1-1 (RAR-) - R19-2 (RAR-) Always Below 1 Ω
S1-2 (RAR+) - R19-1 (RAR+) Always Below 1 Ω
S1-3 (RBR-) - R19-4 (RBR-) Always Below 1 Ω
S1-4 (RBR+) - R19-3 (RBR+) Always Below 1 Ω
S1-1 (RAR-) - Body ground Always 10 kΩ or higher
S1-2 (RAR+) - Body ground Always 10 kΩ or higher
S1-3 (RBR-) - Body ground Always 10 kΩ or higher
S1-4 (RBR+) - Body ground Always 10 kΩ or higher

for Rear LH (for DTC C1734/34)
Tester Connection Condition Specified Condition
S4-1 (RAL-) - R19-6 (RAL-) Always Below 1 Ω
S4-2 (RAL+) - R19-5 (RAL+) Always Below 1 Ω
S4-3 (RBL-) - R19-8 (RBL-) Always Below 1 Ω
S4-4 (RBL+) - R19-7 (RBL+) Always Below 1 Ω
S4-1 (RAL-) - Body ground Always 10 kΩ or higher
S4-2 (RAL+) - Body ground Always 10 kΩ or higher
S4-3 (RBL-) - Body ground Always 10 kΩ or higher
S4-4 (RBL+) - Body ground Always 10 kΩ or higher





OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR