Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260910 ANTI-LOCK BRAKE SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  C1430  Brake Pedal Load Sensing Switch OFF Stuck Malfunction  C1431  Brake Pedal Load Sensing Switch ON Stuck Malfunction  


DESCRIPTION

The brake pedal load sensing switch operates when the brake pedal is depressed with force exceeding a predetermined level.

The skid control ECU detects if the brake pedal is depressed or not via this circuit.

DTC Code DTC Detection Condition Trouble Area
C1430 Either condition is met:
1.

With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the deceleration is 0.4 G or more for 1 second or more.

2.

With the stop light switch on, the brake pedal load sensing switch off and the master cylinder pressure at 6 MPa or more, the vehicle speed is 0 km/h (0 mph) for 5 seconds or more.


·

Brake pedal load sensing switch (Brake with switch pedal sub-assembly)

·

Brake pedal load sensing switch circuit

·

Brake actuator assembly (Skid control ECU)


C1431 Either condition is met:
1.

Immediately after the ignition switch is turned to ON, the brake pedal load sensing switch is on and the stop light switch is off for 10 seconds or more.

2.

The condition that the brake pedal load sensing switch remains on while the vehicle speed increases from 0 km/h (0 mph) to 30 km/h (18 mph) occurs 5 times in succession.



CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>CALIBRATION).


HINT:

When DTC C1425 is output together with DTC C1430 and/or C1431, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>C1425).


PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SW/BRAKE PEDAL LOAD SENSING SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop Light SW Stop light switch / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON: Brake pedal depressed beyond specified point
OFF: Brake pedal not depressed beyond specified point
-


f.

Check that the stop light switch display and brake pedal load sensing switch display observed on the intelligent tester change according to the brake pedal operation.

OK:

The intelligent tester displays ON or OFF according to brake pedal operation.



g.

Slowly depress the brake pedal and check when the stop light switch and brake pedal load sensing switch turn ON.

OK:

The stop light switch turns on first, and then the brake pedal load sensing switch turns on.


Result
Result Proceed to
OK A
NG Turning on of brake pedal load sensing switch is not confirmed B
Brake pedal load sensing switch turns on first C



A

2.RECONFIRM DTC

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

C

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
2.RECONFIRM DTC
a.

Turn the ignition switch off.



c.

Start the engine.


d.

Perform a road and braking test.


e.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTCs C1430 and C1431 are not output A
DTCs C1430 and/or C1431 are output B



A

B

3.INSPECT BRAKE PEDAL LOAD SENSING SWITCH

OK

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

NG

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BRAKE PEDAL LOAD SENSING SWITCH)

OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Vacuum Brake Booster)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch installation are normal.




OK

REPLACE BRAKE WITH SWITCH PEDAL SUB-ASSEMBLY

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH