Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  Crawl Indicator Light does not Come ON  


DESCRIPTION

If the following condition is met, the crawl indicator light turns off and crawl control is stopped.

Crawl control is operated when the vehicle stability control system is malfunctioning, or a vehicle stability control system malfunction occurs during crawl control.


If any of the following conditions are met, the crawl indicator light blinks and crawl control is stopped.

·

The transfer is shifted to H4 during crawl control.

·

The shift lever is moved to P or N during crawl control.

·

The driver side door is opened during crawl control.


When the vehicle is driven at 25 km/h (16 mph) or more during crawl control, control is temporarily stopped and the crawl indicator light blinks.

When using crawl control continually for a long period of time, if the temperature inside the hydraulic brake booster becomes too high, the crawl indicator light will turn off. After a while, the temperature decreases and crawl control becomes operable.

WIRING DIAGRAM

C294551E03
4.167,3.719 4.688,4.073 0.521,0.354 10 false G156 4.563,3 6.302,3.271 1.74,0.271 10 false Crawl Speed Selector 3.979,0.792 4.323,1.063 0.344,0.271 10 false 21 4.208,1.906 4.698,2.156 0.49,0.25 10 false ECU 4.427,1.094 6.125,1.271 1.698,0.177 10 false Crawl On/Off Switch 6.198,0.813 6.469,1.063 0.271,0.25 10 false E 6.385,0.802 6.771,1.063 0.385,0.26 10 false 24 4.219,2.156 4.604,2.385 0.385,0.229 10 false UP 3.958,1.896 4.302,2.146 0.344,0.25 10 false 17 4.219,2.417 4.656,2.667 0.438,0.25 10 false DN 3.958,2.417 4.333,2.656 0.375,0.24 10 false 19 2.792,0.896 3.375,1.146 0.583,0.25 10 false CRWL 3.281,0.792 3.667,1.063 0.385,0.271 10 false 6 2.781,2.51 3.302,2.76 0.521,0.25 10 false MOD3 3.271,1.906 3.615,2.146 0.344,0.24 10 false 4 2.781,2.25 3.323,2.542 0.542,0.292 10 false MOD2 3.281,2.156 3.583,2.375 0.302,0.219 10 false 2 2,3.104 2.469,3.365 0.469,0.26 10 false G162 2.615,5.573 2.948,5.813 0.333,0.24 10 false A7 2.604,5.719 5.958,6.094 3.354,0.375 10 false Skid Control ECU (Master Cylinder Solenoid) 0.646,2.667 1.26,2.906 0.615,0.24 10 false CRAWL 0.083,3.583 0.531,3.865 0.448,0.281 10 false G6 0.083,3.74 1.26,4.094 1.177,0.354 10 false Combination Meter Assembly 0.688,6.24 2.677,6.635 1.99,0.396 10 false : CAN Communication System 2,3.302 3.375,3.74 1.375,0.438 10 false Driving Support Switch Control ECU 2.771,2 3.365,2.25 0.594,0.25 10 false MOD1 3.26,2.406 3.625,2.656 0.365,0.25 10 false 11 3.958,2.146 4.125,2.302 0.167,0.156 10 false 18 4.583,1.771 4.896,2.021 0.313,0.25 10 false 1 4.833,1.771 5.156,1.99 0.323,0.219 10 false 2 5.083,1.771 5.417,2.021 0.333,0.25 10 false 3 5.333,1.771 5.646,2.01 0.313,0.24 10 false 4 5.604,1.771 5.896,2.021 0.292,0.25 10 false 5 4.198,0.792 4.771,1.042 0.573,0.25 10 false FRB 4.167,3.906 6.24,4.208 2.073,0.302 10 false Center Cluster Module Switch

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

2.CHECK FOR DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)

B

3.READ VALUE USING GTS (CRAWL CONTROL MAIN SWITCH AND DIAL SWITCH SIGNAL)

OK

4.PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)

NG

5.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)
4.PERFORM ACTIVE TEST USING GTS (CRAWL CONTROL LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Crawl Control Light Crawl indicator light Indicator light ON/OFF Observe combination meter


f.

When performing the Crawl Control Light Active Test, check Crawl Control Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DATA LIST / ACTIVE TEST).

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Crawl Control Light Crawl indicator light/ ON or OFF ON: Indicator light on
OFF: Indicator light off
-

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

5.CHECK HARNESS AND CONNECTOR (CENTER CLUSTER MODULE SWITCH - DRIVING SUPPORT SWITCH CONTROL ECU)

OK

6.INSPECT CENTER CLUSTER MODULE SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR