Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) › 2015.06–2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260912 VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)  Brake Warning Light Remains ON  


DESCRIPTION

The skid control ECU is connected to the combination meter via CAN communication.

If any of the following is detected, the brake warning light remains on:

·

The skid control ECU connector is disconnected from the skid control ECU.

·

The brake fluid level is insufficient.

·

The parking brake is applied.

·

EBD operation is not possible.

·

The voltage at terminal IG1 is high.


WIRING DIAGRAM

C215176E12
5.031,4.802 5.323,5.021 0.292,0.219 10 false A6 5.031,4.99 6.656,5.385 1.625,0.396 10 false Brake Actuator Assembly (Skid Control ECU) 2.354,0.906 3.771,1.146 1.417,0.24 10 false Parking Brake Switch 4.74,2.021 5.052,2.188 0.313,0.167 10 false A 4.74,2.198 6.604,2.573 1.865,0.375 10 false Main Body ECU (Multiplex Network Body ECU) 2.385,3.427 3.542,3.833 1.156,0.406 10 false Brake Fluid Level Warning Switch 0.583,4.479 1.844,4.677 1.26,0.198 10 false Combination Meter 0.656,5.313 3.021,5.521 2.365,0.208 10 false : CAN Communication System 1.083,3.229 1.531,3.427 0.448,0.198 10 false Brake 1.302,3.708 1.583,3.875 0.281,0.167 10 false IG 2.615,4.427 3.74,4.625 1.125,0.198 10 false from IG1 Circuit 3.917,4.625 4.833,4.802 0.917,0.177 10 false ECU-IG NO. 1 4.823,4.26 5.063,4.469 0.24,0.208 10 false 34 4.906,3.802 5.083,3.99 0.177,0.188 10 false 1 5.156,4.333 5.448,4.521 0.292,0.188 10 false IG1 5.167,3.865 5.74,4.052 0.573,0.188 10 false GND1 0.865,1.833 1.24,2.135 0.375,0.302 10 false CPU 2.354,0.76 2.708,0.927 0.354,0.167 10 false G77 3.5,0.354 3.615,0.521 0.115,0.167 10 false 1 4.563,0.354 4.75,0.531 0.188,0.177 10 false 12 4.833,0.49 5.177,0.646 0.344,0.156 10 false PKB 0.583,4.333 0.833,4.51 0.25,0.177 10 false G6 1.927,2.771 2.156,2.938 0.229,0.167 10 false 31 1.583,2.948 1.865,3.094 0.281,0.146 10 false SW 2.281,2.781 2.427,3 0.146,0.219 10 false 1 3.26,2.771 3.417,2.958 0.156,0.188 10 false 2 2.385,3.25 2.667,3.417 0.281,0.167 10 false A44

CAUTION / NOTICE / HINT

NOTICE:

When replacing the brake actuator assembly, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>CALIBRATION).


PROCEDURE

2.CHECK IF SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU connector is securely connected.

OK:

The connector is securely connected.




OK

3.CHECK TERMINAL VOLTAGE (IG1)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK TERMINAL VOLTAGE (IG1)

OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

OK

5.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

5.READ VALUE USING INTELLIGENT TESTER (PARKING BRAKE SW)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Parking Brake SW Parking brake switch / ON or OFF ON: Parking brake applied
OFF: Parking brake released
-


f.

Using the intelligent tester, check the input of the switch operation when the parking brake pedal is operated.

OK:

When the parking brake is operated, the display changes as shown above.




OK

6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH

NG

9.INSPECT PARKING BRAKE SWITCH
6.INSPECT BRAKE FLUID LEVEL WARNING SWITCH
a.

Turn the ignition switch off.


b.

Remove the reservoir filler cap and strainer.


c.

Disconnect the A44 brake fluid level warning switch connector.


d.
C219276E01
0.185,0.156 0.410,0.308 0.225,0.152 10 *a

Measure the resistance according to the value(s) in the table below.

HINT:

A float is located inside the reservoir. Its position can be changed by increasing or decreasing the level of brake fluid.


Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - 2 Switch off (Float up) 10 kΩ or higher
Switch on (Float down) Below 1 Ω


Text in Illustration
*a Component without harness connected
(Brake Fluid Level Warning Switch)

HINT:

If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.




OK

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)

NG

REPLACE BRAKE MASTER CYLINDER RESERVOIR ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - BRAKE FLUID LEVEL WARNING SWITCH)
a.

Disconnect the G6 combination meter connector.


b.

Disconnect the A44 brake fluid level warning switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-31 (SW) - A44-1 Always Below 1 Ω
G6-31 (SW) - Body ground Always 10 kΩ or higher
A44-2 - Body ground Always Below 1 Ω




OK

8.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.READ VALUE USING INTELLIGENT TESTER (BRAKE WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the intelligent tester to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the intelligent tester on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Brake Warning Light Brake warning light / ON or OFF OFF -


f.

When performing the Brake Warning Light Active Test, check Brake Warning Light in the Data List (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM(for Vacuum Brake Booster)>DATA LIST / ACTIVE TEST).


ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
Brake Warning Light Brake warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B


A

B

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

9.INSPECT PARKING BRAKE SWITCH
a.

Turn the ignition switch off.


b.

Disconnect the G77 parking brake switch connector.


c.
C215408E01
0.223,0.014 0.560,0.229 0.336,0.215 10 *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 - Body ground Parking brake switch on
(Switch pin not pushed in)
Below 1 Ω
Parking brake switch off
(Switch pin pushed in)
10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Parking Brake Switch)



OK

10.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)

NG

REPLACE PARKING BRAKE SWITCH

10.CHECK HARNESS AND CONNECTOR (PARKING BRAKE SWITCH - MAIN BODY ECU)
a.

b.

Disconnect the G77 parking brake switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-12 (PKB) - G77-1 Always Below 1 Ω
A-12 (PKB) - Body ground Always 10 kΩ or higher




OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR