Home › Steering › POWER ASSIST SYSTEMS › POWER STEERING SYSTEM (w/ VSC) › 2015.06–2018.06
RM27T0E _55 Steering _053717 POWER ASSIST SYSTEMS _0260945 POWER STEERING SYSTEM(w/ VSC) C

POWER ASSIST SYSTEMS  POWER STEERING SYSTEM(w/ VSC)  C15F0  VFC Solenoid Circuit  


DESCRIPTION

This circuit supplies electric power to the power steering solenoid valve.

The power steering ECU controls the output current to the power steering solenoid valve in accordance with the steering angle signal, steering zero point memory, vehicle speed signal and engine speed signal, adjusting the amount of power steering assist.

DTC Code DTC Detection Condition Trouble area
C15F0 A short or open in the solenoid valve circuit
·

Harness or connector

·

Vane pump assembly

·

Power steering ECU assembly



WIRING DIAGRAM

C210556E18
5.313,2.396 6.615,2.573 1.302,0.177 10 false Power Steering ECU 1.979,1.156 3.906,1.333 1.927,0.177 10 false Power Steering Solenoid Valve 5.5,0.74 5.969,0.927 0.469,0.188 10 false SOF+ 5.5,1.698 5.854,1.875 0.354,0.177 10 false SOF- 5.302,0.656 5.458,0.833 0.156,0.177 10 false 7 5.302,1.604 5.458,1.781 0.156,0.177 10 false 8 3.5,0.656 3.656,0.833 0.156,0.177 10 false 2 2.208,0.656 2.365,0.833 0.156,0.177 10 false 1 1.99,1 2.406,1.177 0.417,0.177 10 false C156 5.313,2.229 5.729,2.406 0.417,0.177 10 false G46 3,0.656 3.448,0.833 0.448,0.177 10 false SOF+ 2.417,0.656 2.771,0.833 0.354,0.177 10 false SOF-

PROCEDURE

1.READ VALUE USING GTS (SOLENOID CURRENT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / PPS / Data List.

PPS
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Solenoid Current Solenoid Current/
Min.: 0 mA
Max.: 1000 mA
200 to 950 mA The engine is running and the steering wheel is being turned.

OK:

The normal condition value is displayed the GTS.




OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - POWER STEERING SOLENOID VALVE)
2.CHECK HARNESS AND CONNECTOR (POWER STEERING ECU - POWER STEERING SOLENOID VALVE)
a.

Disconnect the power steering ECU and power steering solenoid valve connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G46-7 (SOF+) - C156-2 (SOF+) Always Below 1 Ω
G46-8 (SOF-) - C156-1 (SOF-)
G46-7 (SOF+) - Body ground Always 10 kΩ or higher
G46-8 (SOF-) - Body ground




OK

3.INSPECT POWER STEERING SOLENOID VALVE ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT POWER STEERING SOLENOID VALVE ASSEMBLY
C358280E01
0.844,2.917 1.542,3.313 true 2.448,2.958 1.875,3.333 true 0.823,0.802 1.521,1.198 true 2.448,0.833 1.875,1.208 true 1.292,4.417 1.552,4.625 0.26,0.208 10 false (+) 1.99,4.406 2.219,4.615 0.229,0.208 10 false (-) 0.208,0.698 0.823,0.927 0.615,0.229 10 false 2 (SOF+) 0.24,2.823 0.854,3.052 0.615,0.229 10 false 2 (SOF+) 2.5,0.708 3.063,0.938 0.563,0.229 10 false 1 (SOF-) 2.5,2.844 3.063,3.073 0.563,0.229 10 false 1 (SOF-) 0.146,0.063 0.344,0.271 0.198,0.208 10 false *a

a.

Disconnect the power steering solenoid valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 (SOF-) - 2 (SOF+) 20°C (68°F) 6.7 to 7.3 Ω



c.

Connect the battery positive (+) lead with a 21 W bulb to terminal 2 (SOF+) and the negative (-) lead to terminal 1 (SOF-) of the solenoid valve connector. Then check that the valve moves and makes an operating noise.

OK:

Valve moves and makes an operating noise.



Text in Illustration
*a Component without harness connected
(Power Steering Solenoid Valve)

Result
Result Proceed to
OK A
NG (for 1GD-FTV) B
NG (for 1KD-FTV) C
NG (for 2TR-FE) D
NG (for 1GR-FE) E


A

REPLACE POWER STEERING ECU ASSEMBLY

B

C

D

E