Home › Audio / Visual / Telematics › PARK ASSIST / MONITORING › WIDE VIEW FRONT MONITOR SYSTEM › 2015.06–2017.08
RM27T0E _56 Audio / Visual / Telematics _053722 PARK ASSIST / MONITORING _0261014 WIDE VIEW FRONT MONITOR SYSTEM J

PARK ASSIST / MONITORING  WIDE VIEW FRONT MONITOR SYSTEM  Image from Camera for Wide View Front Monitor is Abnormal  


DESCRIPTION

The display signal of the front television camera assembly is transmitted to the parking assist ECU.

WIRING DIAGRAM

E285880E02
2.347,1.446 2.995,1.624 0.648,0.177 10 H50 2.347,1.6 4.467,1.778 2.120,0.177 10 Navigation Receiver Assembly*2 2.347,1.881 4.978,2.058 2.631,0.177 10 Radio and Display Receiver Assembly*3 0.128,5.837 1.097,6.014 0.969,0.177 10 *1: Shielded 0.128,6.117 2.187,6.294 2.059,0.177 10 *2: for Navigation Receiver Type 0.128,6.397 2.187,6.574 2.059,0.177 10 *3: for Radio and Display Type 0.338,4.87 1.910,5.198 1.571,0.329 10 Front Television Camera Assembly 0.338,4.697 0.986,4.874 0.648,0.177 10 A52 1.137,2.861 1.615,3.039 0.478,0.177 10 BCB+ 1.683,2.763 2.161,2.941 0.478,0.177 10 1 1.683,3.226 2.161,3.403 0.478,0.177 10 2 1.683,3.688 2.161,3.865 0.478,0.177 10 4 1.683,4.164 2.161,4.342 0.478,0.177 10 3 1.137,3.324 1.615,3.501 0.478,0.177 10 BCV+ 1.137,3.772 1.615,3.949 0.478,0.177 10 BCV- 1.137,4.248 1.615,4.426 0.478,0.177 10 BGND 5.578,2.861 6.056,3.039 0.478,0.177 10 BCB+ 5.578,3.324 6.056,3.501 0.478,0.177 10 BCV+ 5.578,3.772 6.056,3.949 0.478,0.177 10 BCV- 5.578,4.248 6.056,4.426 0.478,0.177 10 BGND 2.706,4.412 2.965,4.589 0.259,0.177 10 *1 4.121,4.412 4.380,4.589 0.259,0.177 10 *1 5.438,4.691 5.633,4.868 0.194,0.177 10 I7 5.303,2.754 5.497,2.931 0.194,0.177 10 11 5.578,0.55 6.056,0.727 0.478,0.177 10 NS+ 5.303,0.442 5.497,0.620 0.194,0.177 10 16 5.578,0.844 6.056,1.021 0.478,0.177 10 NS- 5.303,0.736 5.497,0.914 0.194,0.177 10 17 3.738,0.55 3.984,0.727 0.246,0.177 10 V+ 4.056,0.442 4.250,0.620 0.194,0.177 10 12 3.738,0.844 3.984,1.021 0.246,0.177 10 V- 4.056,0.736 4.250,0.914 0.194,0.177 10 24 5.578,1.208 6.056,1.385 0.478,0.177 10 NSG 5.303,1.101 5.497,1.278 0.194,0.177 10 18 3.505,1.208 3.982,1.385 0.478,0.177 10 CGND 4.056,1.101 4.250,1.278 0.194,0.177 10 23 5.303,3.216 5.497,3.394 0.194,0.177 10 12 5.303,3.693 5.497,3.870 0.194,0.177 10 36 5.303,4.155 5.497,4.332 0.194,0.177 10 35 5.438,4.875 6.704,5.203 1.266,0.329 10 Parking Assist ECU 4.383,1.306 4.642,1.483 0.259,0.177 10 *1 4.929,1.306 5.188,1.483 0.259,0.177 10 *1

CAUTION / NOTICE / HINT

NOTICE:
·

When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).

·

Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as wide view front monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).



HINT:

Images may be unclear even in normal conditions if:

·

Electrical devices are used in the cabin (noise may occur in the image).

·

The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).

·

The camera lens is dirty with snow, mud, etc.

·

A strong beam of light, such as a sunbeam or headlight, hits the camera.

·

It is too dark around the camera (at night etc.).

·

The ambient temperature around the camera is either too high or too low.

·

The vehicle is tilted at a steep angle.

·

The camera lens is damaged by plying stones.

·

The front television camera assembly lens is scratched.

·

The front television camera assembly lens has drops of water on it or the humidity is high.

·

When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.



PROCEDURE

1.CHECK SIDE MONITOR SYSTEM
a.

Check if the same malfunction occurs when the side monitor screen is displayed.


Result
Result Proceed to
Malfunction occurs when front monitor screen is displayed (side monitor screen is normal). A
Malfunction occurs when front assist monitor screen and side monitor screen are displayed. B


A

2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)

B

5.CHECK HARNESS AND CONNECTOR
2.CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - FRONT TELEVISION CAMERA ASSEMBLY AND BODY GROUND)

OK

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK PARKING ASSIST ECU (BCB+, BGND)

A

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)

B

C

4.CHECK FRONT TELEVISION CAMERA ASSEMBLY (BCV+, BGND)
a.

Measure the resistance according to the value(s) in the table below.

E348793E06
0.76,0.302 1.188,0.531 0.427,0.229 0.677,1 0.667,0.5 0.667,0.5 0.5,0.5 true 1.083,1.333 0.833,1.333 0.833,1.333 0.698,1.104 true 4.115,2.188 3.906,2.188 3.906,2.188 3.833,1.615 false 4.344,2.01 4.177,2.01 4.177,2.01 3.948,1.563 false 6.24,2.125 6.031,2.125 6.031,2.125 5.958,1.458 false 6.531,1.969 6.365,1.969 6.365,1.969 6.083,1.406 false 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 3.271,0.167 3.583,0.365 0.313,0.198 10 false *b 5.406,0.146 5.719,0.344 0.313,0.198 10 false *c 3.104,1.052 3.448,1.25 0.344,0.198 10 false GND 5.156,1.042 5.5,1.24 0.344,0.198 10 false GND 4.156,2.115 4.469,2.313 0.313,0.198 10 false *d 6.281,2.042 6.594,2.24 0.313,0.198 10 false *d 4.385,1.917 4.698,2.115 0.313,0.198 10 false *e 6.604,1.896 6.917,2.094 0.313,0.198 10 false *e 0.104,0.406 0.573,0.594 0.469,0.188 10 false BCV+ 1.156,1.25 1.625,1.49 0.469,0.24 10 false BGND 0.927,0.333 1.24,0.531 0.313,0.198 10 false I7

Text in Illustration
*a Component with harness connected
(Parking Assist ECU)
*b Waveform A
*c Waveform B *d Synchronized Signal
*e Video Waveform - -

HINT:
·

A waterproof connector is used for the front television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

·

The video waveform changes according to the image sent by the front television camera assembly.



OK:

Waveform is as shown in the illustration.


Item Content
Terminal No. (Symbol) I7-12 (BCV+) - I7-35 (BGND)
Tool Setting 200 mV/DIV., 50 μsec./DIV.
Condition
·

Waveform A: Engine switch on (IG), wide view front and side monitor switch on and camera lens is not covered, displaying an image

·

Waveform B: Engine switch on (IG), wide view front and side monitor switch on and camera lens is covered, blacking out the screen





OK

5.CHECK HARNESS AND CONNECTOR

NG

5.CHECK HARNESS AND CONNECTOR
a.

Disconnect the I7 parking assist ECU connector.


b.

Disconnect the H50 navigation receiver assembly*1 or radio and display receiver assembly*2 connectors.

*1: for Navigation Receiver Type

*2: for Radio and Display Type



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I7-16 (NS+) - H50-12 (V+) Always Below 1 Ω
I7-17 (NS-) - H50-24 (V-) Always Below 1 Ω
I7-18 (NSG) - H50-23 (CGND) Always Below 1 Ω
I7-16 (NS+) - Body ground Always 10 kΩ or higher
I7-17 (NS-) - Body ground Always 10 kΩ or higher
I7-18 (NSG) - Body ground Always Below 1 kΩ



Result
Result Proceed to
OK (for Navigation Receiver Type) A
OK (for Radio and Display Type) B
NG C


A

6.CHECK NAVIGATION RECEIVER ASSEMBLY

B

7.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK NAVIGATION RECEIVER ASSEMBLY
a.

Replace the navigation receiver assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).


b.

Check if the same malfunction recurs when the front monitor and side monitor screens are displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result
Proceed to Result
OK A
NG (for LHD) B
NG (for RHD) C


A

END (NAVIGATION RECEIVER ASSEMBLY IS DEFECTIVE)

B

C

7.CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY
a.

Replace the radio and display receiver assembly with a normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).


b.

Check if the same malfunction recurs when the front monitor and side monitor screens are displayed.

OK:

Malfunction does not reoccur (returns to normal).



Result
Proceed to Result
OK A
NG (for LHD) B
NG (for RHD) C


A

END (RADIO AND DISPLAY RECEIVER ASSEMBLY IS DEFECTIVE)

B

C