The display signal from the rear television camera assembly is transmitted to the navigation receiver assembly*1 or radio and display receiver assembly*2 via the parking assist ECU.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
When "System initializing" is displayed on the parking assist ECU after the battery terminal has been disconnected, correct the steering angle neutral point (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>INITIALIZATION).
Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (See page Audio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING ASSIST MONITOR SYSTEM(w/ Side Monitor System)>CALIBRATION).
Images may be unclear even in normal conditions if:
Electrical devices are used in the cabin (noise may occur in the image).
The camera lens is frosted over (the image immediately after turning the engine switch on (IG) may be blurred or darker than normal).
The camera lens is dirty with snow, mud, etc.
A strong beam of light, such as a sunbeam or headlight, hits the camera.
It is too dark around the camera (at night etc.).
The ambient temperature around the camera is either too high or too low.
The vehicle is tilted at a steep angle.
The rear television camera assembly lens is scratched.
The rear television camera assembly lens has drops of water on it or the humidity is high.
When the camera is used under fluorescent lights, sodium lights, or mercury lights etc., the lights and the illuminated area may appear to flicker.
Check if the same malfunction occurs when the side monitor screen is displayed.
| Result | Proceed to |
|---|---|
| Malfunction occurs when parking assist monitor screen is displayed (side monitor screen is normal). | A |
| Malfunction occurs when parking assist monitor screen and side monitor screen are displayed. | B |
A
B
OK
NG
A
B
C
| *a | Component with harness connected
(Parking Assist ECU) |
*b | Waveform A |
| *c | Waveform B | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
Check the waveform of the rear television camera assembly using an oscilloscope.
A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the navigation receiver assembly*1 or radio and display receiver assembly*2 with the connector connected.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
The video waveform changes according to the image sent by the rear television camera assembly.
| Item | Content |
|---|---|
| Terminal No. (Symbol) | I7-15 (CV+) - I7-37 (CGND) |
| Tool Setting | 200 mV/DIV., 50 μsec./DIV. |
| Condition | ·
Waveform A: Engine switch on (IG), camera lens is not covered, displaying an image ·
Waveform B: Engine switch on (IG), camera lens is covered, blacking out the screen |
Waveform is as shown in the illustration.
| Proceed to | Result |
|---|---|
| OK | A |
| NG (w/ Tire Carrier) | B |
| NG (w/o Tire Carrier) | C |
A
B
C
Disconnect the I7 parking assist ECU connector.
Disconnect the H50 navigation receiver assembly*1 or radio and display receiver assembly*2 connectors.
*1: for Navigation Receiver Type
*2: for Radio and Display Type
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I7-16 (NS+) - H50-12 (V+) | Always | Below 1 Ω |
| I7-17 (NS-) - H50-24 (V-) | Always | Below 1 Ω |
| I7-18 (NSG) - H50-23 (CGND) | Always | Below 1 Ω |
| I7-16 (NS+) - Body ground | Always | 10 kΩ or higher |
| I7-17 (NS-) - Body ground | Always | 10 kΩ or higher |
| I7-18 (NSG) - Body ground | Always | Below 1 kΩ |
| Result | Proceed to |
|---|---|
| OK (for Navigation Receiver Type) | A |
| OK (for Radio and Display Type) | B |
| NG | C |
A
B
C
Replace the navigation receiver assembly with a normally functioning one (See page Audio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION RECEIVER>REMOVAL).
Check if the same malfunction recurs when the parking assist monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to | Result |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C
Replace the radio and display receiver assembly with a normally functioning one (See page Audio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL).
Check if the same malfunction recurs when the parking assist monitor screen is displayed.
Malfunction does not reoccur (returns to normal).
| Proceed to | Result |
|---|---|
| OK (for LHD) | A |
| OK (for RHD) | B |
| NG | C |
A
B
C