Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0261225 POWER WINDOW CONTROL SYSTEM C

WINDOW / GLASS  POWER WINDOW CONTROL SYSTEM  B2312  Power Window Switch Malfunction  


DESCRIPTION

The power window regulator motor assemblies are operated by the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assemblies*.

The power window regulator motor assemblies have motor, regulator and ECU functions.

This DTC is output when an ECU built into a power window regulator motor assembly and multiplex network master switch assembly determines that the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly* is stuck.

*: for 5 Door


Master Switch
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The multiplex network master switch assembly is stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds

·

Multiplex network master switch assembly operated for 20 seconds or more


Multiplex network master switch assembly

D-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The multiplex network master switch assembly is stuck

·

Multiplex network master switch assembly held in same position for more than 20 seconds


·

Multiplex network master switch assembly

·

Front power window regulator motor assembly LH (for LHD)

·

Front power window regulator motor assembly RH (for RHD)

·

Harness or connector



P-Door Motor
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

The Power window regulator switch assembly is stuck

·

Power window regulator switch assembly held in same position for more than 20 seconds


·

Power window regulator switch assembly

·

Front power window regulator motor assembly RH (for LHD)

·

Front power window regulator motor assembly LH (for RHD)

·

Harness or connector



RL-Door Motor (for 5 Door)
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

Rear power window regulator switch assembly (for Rear LH Door) stuck

·

Rear power window regulator switch assembly (for Rear LH Door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for Rear LH Door)

·

Rear power window regulator motor LH

·

Harness or connector



RR-Door Motor (for 5 Door)
DTC Code DTC Detection Condition Trouble Area
B2312 Either condition is met:
·

Rear power window regulator switch assembly (for Rear RH Door) stuck

·

Rear power window regulator switch assembly (for Rear RH Door) held in same position for more than 20 seconds


·

Rear power window regulator switch assembly (for Rear RH Door)

·

Rear power window regulator motor RH

·

Harness or connector



WIRING DIAGRAM

for Driver Side:


B449848E01
0.354,0.698 3.417,0.885 3.063,0.188 10 false Main Body ECU (Multiplex Network Body ECU) 0.917,2.896 2.531,3.313 1.615,0.417 10 false Multiplex Network Master Switch Assembly 1.865,1.51 2.177,1.708 0.313,0.198 10 false UP 1.677,1.948 2.323,2.198 0.646,0.25 10 false DOWN 4.917,2.917 6.833,3.333 1.917,0.417 10 false Front Power Window Regulator Motor Assembly LH 4.917,3.917 6.833,4.333 1.917,0.417 10 false Front Power Window Regulator Motor Assembly RH 4.917,2.729 5.313,2.896 0.396,0.167 10 false K7*1 4.917,3.729 5.313,3.896 0.396,0.167 10 false J7*2 0.917,2.708 1.75,2.875 0.833,0.167 10 false K4*1, J9*2 0.729,4.385 2.542,4.573 1.813,0.188 10 false : LIN Communication Line 5.521,1.948 6.167,2.198 0.646,0.25 10 false DOWN 5.521,1.5 5.833,1.698 0.313,0.198 10 false UP 2.271,1.365 2.583,1.563 0.313,0.198 10 false 20 5.167,1.396 5.479,1.594 0.313,0.198 10 false 10 2.271,1.823 2.583,2.021 0.313,0.198 10 false 15 5.25,1.823 5.406,2.021 0.156,0.198 10 false 7 0.25,3.708 1.281,3.927 1.031,0.219 10 false *1: for LHD 0.25,4.052 1.281,4.271 1.031,0.219 10 false *2: for RHD


for Front Passenger Side:


B449849E01
0.76,4.406 2.51,4.656 1.75,0.25 10 false : LIN Communication Line 1.667,0.833 4.917,1.083 3.25,0.25 10 false Main Body ECU (Multiplex Network Body ECU) 2.333,3.177 3.917,3.542 1.583,0.365 10 false Power Window Regulator Switch Assembly 4.917,3.104 6.833,3.469 1.917,0.365 10 false Front Power Window Regulator Motor Assembly RH 4.917,4.021 6.833,4.385 1.917,0.365 10 false Front Power Window Regulator Motor Assembly LH 2.323,3 4.073,3.25 1.75,0.25 10 false J1*1, K10*2 4.917,2.917 5.417,3.167 0.5,0.25 10 false J7*1 4.917,3.833 5.417,4.083 0.5,0.25 10 false K7*2 0.333,3.75 1.417,3.917 1.083,0.167 10 false *1: for LHD 0.333,4.083 1.417,4.25 1.083,0.167 10 false *2: for RHD 2.625,2.542 3.083,2.75 0.458,0.208 10 false GND 3.167,2.531 3.708,2.74 0.542,0.208 10 false AUTO 3.073,2.094 3.615,2.302 0.542,0.208 10 false DOWN 5.479,2.094 6.021,2.302 0.542,0.208 10 false DOWN 5.49,2.542 6.031,2.75 0.542,0.208 10 false AUTO 3.333,1.635 3.646,1.833 0.313,0.198 10 false UP 5.5,1.635 5.813,1.833 0.313,0.198 10 false UP 5.167,1.5 5.479,1.698 0.313,0.198 10 false 10 3.677,1.5 3.833,1.698 0.156,0.198 10 false 6 3.677,1.969 3.833,2.167 0.156,0.198 10 false 7 3.677,2.417 3.833,2.615 0.156,0.198 10 false 8 5.25,1.969 5.406,2.167 0.156,0.198 10 false 7 5.25,2.417 5.406,2.615 0.156,0.198 10 false 4 2.344,2.417 2.5,2.615 0.156,0.198 10 false 1


for Rear LH (for 5 Door):


B449850E01
0.75,4.396 2.667,4.583 1.917,0.188 10 false : LIN Communication Line 2.25,3.552 4.167,3.917 1.917,0.365 10 false Rear Power Window Regulator Switch Assembly LH 4.917,3.552 6.833,3.917 1.917,0.365 10 false Rear Power Window Regulator Motor Assembly LH 2.25,3.385 2.563,3.583 0.313,0.198 10 false M2 4.917,3.375 5.229,3.573 0.313,0.198 10 false M4 1.583,1 4.833,1.25 3.25,0.25 10 false Main Body ECU (Multiplex Network Body ECU) 2.625,2.802 3.083,3 0.458,0.198 10 false GND 3.063,2.365 3.677,2.563 0.615,0.198 10 false DOWN 5.49,2.365 6.104,2.563 0.615,0.198 10 false DOWN 5.49,2.802 6.104,3 0.615,0.198 10 false AUTO 3.156,2.802 3.771,3 0.615,0.198 10 false AUTO 3.333,1.917 3.646,2.115 0.313,0.198 10 false UP 5.5,1.917 5.813,2.115 0.313,0.198 10 false UP 5.188,1.802 5.5,2 0.313,0.198 10 false 10 3.677,1.802 3.833,2 0.156,0.198 10 false 6 3.677,2.25 3.833,2.448 0.156,0.198 10 false 7 3.677,2.708 3.833,2.906 0.156,0.198 10 false 8 5.25,2.25 5.406,2.448 0.156,0.198 10 false 7 5.26,2.708 5.417,2.906 0.156,0.198 10 false 4 2.365,2.719 2.521,2.917 0.156,0.198 10 false 1


for Rear RH (for 5 Door):


B449850E02
0.75,4.396 2.667,4.583 1.917,0.188 10 false : LIN Communication Line 2.25,3.552 4.167,3.917 1.917,0.365 10 false Rear Power Window Regulator Switch Assembly RH 4.917,3.552 6.833,3.917 1.917,0.365 10 false Rear Power Window Regulator Motor Assembly RH 2.25,3.385 2.563,3.583 0.313,0.198 10 false L2 4.917,3.375 5.229,3.573 0.313,0.198 10 false L4 1.583,1 4.833,1.25 3.25,0.25 10 false Main Body ECU (Multiplex Network Body ECU) 2.625,2.802 3.083,3 0.458,0.198 10 false GND 3.063,2.365 3.677,2.563 0.615,0.198 10 false DOWN 5.49,2.365 6.104,2.563 0.615,0.198 10 false DOWN 5.49,2.802 6.104,3 0.615,0.198 10 false AUTO 3.156,2.802 3.771,3 0.615,0.198 10 false AUTO 3.333,1.917 3.646,2.115 0.313,0.198 10 false UP 5.5,1.917 5.813,2.115 0.313,0.198 10 false UP 5.188,1.802 5.5,2 0.313,0.198 10 false 10 3.677,1.802 3.833,2 0.156,0.198 10 false 6 3.677,2.25 3.833,2.448 0.156,0.198 10 false 7 3.677,2.708 3.833,2.906 0.156,0.198 10 false 8 5.25,2.25 5.406,2.448 0.156,0.198 10 false 7 5.26,2.708 5.417,2.906 0.156,0.198 10 false 4 2.365,2.719 2.521,2.917 0.156,0.198 10 false 1


CAUTION / NOTICE / HINT

NOTICE:
·

DTC B2312 is stored in the multiplex network master switch assembly and in each power window regulator motor assembly.

·

If a power window regulator motor assembly has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).



HINT:

If DTC B2312 is not output again after the DTC has been cleared, the DTC was output due to the switch being held.


PROCEDURE

1.CHECK FOR DTC

OK

END (DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE)

NG

2.CHECK DTC OUTPUT
2.CHECK DTC OUTPUT
a.

Check the parts which the DTCs have been output from.

Result
Result Proceed to
DTC output from Master Switch A
DTC output from D-Door Motor B
DTC output from P-Door Motor C
DTC output from RL-Door Motor (for 5 Door) D
DTC output from RR-Door Motor (for 5 Door) E



A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

B

3.READ VALUE USING GTS (D-DOOR MOTOR)

C

10.READ VALUE USING GTS (P-DOOR MOTOR)

D

14.READ VALUE USING GTS (RL-DOOR MOTOR)

E

17.READ VALUE USING GTS (RR-DOOR MOTOR)
3.READ VALUE USING GTS (D-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

D-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
D Door P/W Up SW Driver door power window manual up switch signal / OFF or ON OFF: Driver door power window manual up switch not being operated
ON: Driver door power window manual up switch being operated
-
D Door P/W Down SW Driver door power window manual down switch signal / OFF or ON OFF: Driver door power window manual down switch not being operated
ON: Driver door power window manual down switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG (for LHD) C
NG (for RHD) D



A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

C

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

D

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the K4 multiplex network master switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K4-20 (UP) - K7-10 (UP) Always Below 1 Ω
K4-15 (DOWN) - K7-7 (DOWN) Always Below 1 Ω
K4-20 (UP) - Body ground Always 10 kΩ or higher
K4-15 (DOWN) - Body ground Always 10 kΩ or higher




OK

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

6.CHECK FOR DTC
6.CHECK FOR DTC

OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

7.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the J9 multiplex network master switch assembly connector.


b.

Disconnect the J7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J9-20 (UP) - J7-10 (UP) Always Below 1 Ω
J9-15 (DOWN) - J7-7 (DOWN) Always Below 1 Ω
J9-20 (UP) - Body ground Always 10 kΩ or higher
J9-15 (DOWN) - Body ground Always 10 kΩ or higher




OK

8.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY
a.

Replace the multiplex network master switch assembly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW MASTER SWITCH>REMOVAL).



NEXT

9.CHECK FOR DTC
9.CHECK FOR DTC

OK

END (MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

NG

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

10.READ VALUE USING GTS (P-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

P-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
P Door P/W Auto SW Front passenger door power window auto switch signal / OFF or ON OFF: Front passenger door power window auto switch not being operated
ON: Front passenger door power window auto switch being operated
-
P Door P/W Up SW Front passenger door power window manual up switch signal / OFF or ON OFF: Front passenger door power window manual up switch not being operated
ON: Front passenger door power window manual up switch being operated
-
P Door P/W Down SW Front passenger door power window manual down switch signal / OFF or ON OFF: Front passenger door power window manual down switch not being operated
ON: Front passenger door power window manual down switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.



Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

B

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

C

11.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
11.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY
a.

Remove the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>REMOVAL).


b.

Inspect the power window regulator switch assembly (See page Vehicle Exterior>WINDOW / GLASS>FRONT PASSENGER SIDE POWER WINDOW SWITCH>INSPECTION).


Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C


A

12.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

B

13.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

C

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY

12.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the J1 power window regulator switch assembly connector.


b.

Disconnect the J7 front power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J1-6 (UP) - J7-10 (UP) Always Below 1 Ω
J1-7 (DOWN) - J7-7 (DOWN) Always Below 1 Ω
J1-6 (UP) - Body ground Always 10 kΩ or higher
J1-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the K10 power window regulator switch assembly connector.


b.

Disconnect the K7 front power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
K10-6 (UP) - K7-10 (UP) Always Below 1 Ω
K10-7 (DOWN) - K7-7 (DOWN) Always Below 1 Ω
K10-6 (UP) - Body ground Always 10 kΩ or higher
K10-7 (DOWN) - Body ground Always 10 kΩ or higher




OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.READ VALUE USING GTS (RL-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RL-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RL Door P/W Auto SW Rear LH door power window auto switch signal / OFF or ON OFF: Rear LH door power window auto switch not being operated
ON: Rear LH door power window auto switch being operated
-
RL Door P/W Up SW Rear LH door power window manual up switch signal / OFF or ON OFF: Rear LH door power window manual up switch not being operated
ON: Rear LH door power window manual up switch being operated
-
RL Door P/W Down SW Rear LH door power window manual down switch signal / OFF or ON OFF: Rear LH door power window manual down switch not being operated
ON: Rear LH door power window manual down switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

15.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
15.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.

Remove the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW REGULATOR MOTOR (for Rear Door)>REMOVAL).


b.

Inspect the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION).



OK

16.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

16.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
a.

Disconnect the M2 rear power window regulator switch assembly LH connector.


b.

Disconnect the M4 rear power window regulator motor assembly LH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
M2-6 (UP) - M4-10 (UP) Always Below 1 Ω
M2-7 (DOWN) - M4-7 (DOWN) Always Below 1 Ω
M2-8 (AUTO) - M4-4 (AUTO) Always Below 1 Ω
M2-6 (UP) - Body ground Always 10 kΩ or higher
M2-7 (DOWN) - Body ground Always 10 kΩ or higher
M2-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.READ VALUE USING GTS (RR-DOOR MOTOR)
a.

Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).

RR-Door Motor
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
RR Door P/W Auto SW Rear RH door power window auto switch signal / OFF or ON OFF: Rear RH door power window auto switch not being operated
ON: Rear RH door power window auto switch being operated
-
RR Door P/W Up SW Rear RH door power window manual up switch signal / OFF or ON OFF: Rear RH door power window manual up switch not being operated
ON: Rear RH door power window manual up switch being operated
-
RR Door P/W Down SW Rear RH door power window manual down switch signal / OFF or ON OFF: Rear RH door power window manual down switch not being operated
ON: Rear RH door power window manual down switch being operated
-

OK:

On the GTS screen, ON or OFF is displayed accordingly.




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

18.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
18.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
a.

Remove the rear power window regulator switch assembly RH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).


b.

Inspect the rear power window regulator switch assembly RH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION).



OK

19.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)

NG

REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH

19.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
a.

Disconnect the L2 rear power window regulator switch assembly RH connector.


b.

Disconnect the L4 rear power window regulator motor assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L2-6 (UP) - L4-10 (UP) Always Below 1 Ω
L2-7 (DOWN) - L4-7 (DOWN) Always Below 1 Ω
L2-8 (AUTO) - L4-4 (AUTO) Always Below 1 Ω
L2-6 (UP) - Body ground Always 10 kΩ or higher
L2-7 (DOWN) - Body ground Always 10 kΩ or higher
L2-8 (AUTO) - Body ground Always 10 kΩ or higher




OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR