Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › 2015.06–2020.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261248 REAR DOOR A

DOOR / HATCH  REAR DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart (See page General>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS).



PROCEDURE

Hide 75762A 6.INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH

Hide 67003C 8.INSTALL REAR DOOR PANEL CUSHION

a.

Attach the clip to install a new door panel cushion.


Hide 67888A 9.INSTALL REAR DOOR NO. 2 WEATHERSTRIP LH

a.

Attach the 6 clips and guide to install the rear door No. 2 weatherstrip.


Hide 67872 10.INSTALL REAR DOOR WEATHERSTRIP LH

a.

Attach the 19 clips and guide to install the rear door weatherstrip.


Hide 68640A 11.INSTALL REAR DOOR CHECK ASSEMBLY LH

a.
B239622

Install the door check to the door panel with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the door check to the body panel with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 69204A 12.INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door outside handle frame sub-assembly.


b.
B239673

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the rear door outside handle frame sub-assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69254B 13.INSTALL REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH

a.

Attach the 2 claws to install the rear door No. 2 outside handle pad.


Hide 69252B 14.INSTALL REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH

a.

Attach the 3 claws to install the rear door No. 1 outside handle pad.


Hide 69240 15.INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B239665

Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

NOTICE:

If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate will be damaged.



b.

Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.


c.
B239663

Move the lever in the direction indicated by the arrow in the illustration to lock the door outside handle assembly.


Hide 69227L 16.INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

a.

Attach the claw to install the rear door outside handle cover.


b.

Using a T30 "TORX" socket wrench, install the rear door outside handle cover with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


Hide 69780B 17.INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the rear door inside locking cable assembly.


b.

Attach the 3 claws.


Hide 69740D 18.INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the rear door lock remote control cable assembly.


b.

Attach the claw.


Hide 69340 19.INSTALL REAR DOOR LOCK ASSEMBLY LH

Hide 85710E 20.INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69840A 21.INSTALL REAR DOOR WINDOW REGULATOR ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the rear door window regulator assembly.


b.

Install the temporary bolt to the rear door window regulator assembly.


c.
B239642E07
1.438,0.813 1.885,0.813 1.885,0.813 1.979,1.208 true 1.24,0.719 1.469,0.938 0.229,0.219 10 true *1 2.333,2.083 2.583,2.333 0.25,0.25 10 true (1) 3.125,1.302 3.354,1.563 0.229,0.26 10 true (2) 3.167,1.771 3.385,2.031 0.219,0.26 10 true (3) 2.021,1.031 2.323,1.292 0.302,0.26 10 false (4)

Temporarily install the rear door window regulator assembly with the temporary bolt.

Text in Illustration
*1 Temporary Bolt


d.

Temporarily install the 3 bolts, and then tighten the temporary bolt and 3 bolts.

HINT:

Tighten the bolts in the order shown in the illustration.


Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 69975A 22.INSTALL REAR DOOR GLASS CHANNEL FILLER

a.
B234459E02
0.364,0.562 0.557,0.733 0.193,0.171 10 A 2.948,0.55 3.141,0.721 0.193,0.171 10 B 0.616,0.184 0.818,0.345 0.202,0.162 10 *a 2.627,0.172 2.829,0.334 0.202,0.162 10 *b

Apply soapy water to a new rear door glass channel filler.

Standard:
Area Specified Condition
A 21 mm (0.827 in.)
B 22.5 mm (0.886 in.)


Text in Illustration
*a Front Side
*b Rear Side


b.

Install the rear door glass channel filler to the position shown in the illustration.


Hide 69906B 23.INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH

a.
B234461E03
0.603,0.185 0.801,0.347 0.198,0.163 10 *a 2.606,0.185 2.803,0.347 0.198,0.163 10 *b 0.363,0.589 0.560,0.751 0.198,0.163 10 A 2.958,0.597 3.155,0.760 0.198,0.163 10 B

Apply soapy water to a new rear door glass channel sub-assembly.

Standard:
Area Specified Condition
A 21 mm (0.827 in.)
B 22.5 mm (0.886 in.)


Text in Illustration
*a Front Side
*b Rear Side

NOTICE:

To prevent damaging the rear door glass sub-assembly, be careful not to strike the channel with too much force.



b.

Install the rear door glass channel sub-assembly to the position shown in the illustration.


Hide 68104 24.INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.


b.
B241339

Connect the power window regulator switch assembly and move the arm of the regulator so that the roller on the arm can be seen through the service hole.


c.

Disconnect the power window regulator switch assembly and rear power window regulator motor connector.


d.

Disconnect the cable from the negative (-) battery terminal.

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).




e.
B239637

Insert the rear door glass sub-assembly into the rear door panel along the rear door glass run as indicated by the arrow in the illustration.


Hide 68189 25.INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH

a.
B241322

Install the rear door quarter window weatherstrip to the rear door quarter window glass.


Hide 68124B 26.INSTALL REAR DOOR QUARTER WINDOW GLASS LH

a.
B239633

Install the rear door quarter window glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


Hide 67674A 27.INSTALL REAR DOOR FRAME GARNISH LH

a.

Attach the clip to install a new door frame garnish.


Hide 67408E 28.INSTALL REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH

a.

Insert the rear door window division bar sub-assembly from above.


b.

Install the rear door window division bar sub-assembly to the glass run.


c.

Install the temporary bolt to the rear door window division bar sub-assembly.


d.

Install the rear door window division bar sub-assembly.


e.

Install the 2 bolts and screw.


f.

Tighten the temporary bolt to install the rear door window division bar sub-assembly.


Hide 68152C 29.INSTALL REAR DOOR GLASS RUN LH

a.

Install the glass run.


Hide 67842E 30.INSTALL REAR DOOR SERVICE HOLE COVER

a.

Apply new butyl tape to the rear door panel.


b.
B239701E04
0.5,0.51 0.76,0.75 0.26,0.24 10 false *1 2.75,0.5 3.01,0.74 0.26,0.24 10 false *1

Pass the rear door lock remote control cable assembly and rear door inside locking cable assembly through a new rear door service hole cover.


c.

Attach the rear door service hole cover using to the reference points on the rear door panel.

Text in Illustration
*1 Reference Point

NOTICE:
·

There should be no wrinkles or folds after attaching the service hole cover.

·

After attaching the service hole cover, check the seal quality.




d.

Connect the connector.


e.

Attach the 2 clamps to the rear door wire.


Hide 69206C 32.INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B239618

Attach the guide and 2 claws to install the rear door inside handle sub-assembly to the rear door trim board sub-assembly.


b.

Install the 2 screws.


c.
B239610

Install the 8 screws to the rear door armrest.


Hide 86160Y 33.INSTALL REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)

Hide 81081A 34.INSTALL NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY

Hide 81080G 35.INSTALL REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH

Hide 81910D 36.INSTALL REAR REFLEX REFLECTOR ASSEMBLY

a.

Attach the 2 claws to install the rear reflex reflector assembly.


Hide 84810D 37.INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

Hide 68174A 38.INSTALL REAR DOOR INNER GLASS WEATHERSTRIP LH

a.
B239678

Attach the 3 claws to install the rear door inner glass weatherstrip as shown in the illustration.


Hide 67604 39.INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B239680

Install the clamp to the door panel.


b.

Connect the rear door lock remote control cable assembly and rear door inside locking cable assembly.


c.

Connect each connector.


d.
B239608

Attach the rear door trim board sub-assembly by attaching the 4 claws of the rear door inner glass weatherstrip as shown in the illustration.


e.

Attach the 9 clips and install the rear door trim board sub-assembly.


f.

Install the 3 screws.


Hide 74611C 40.INSTALL ASSIST GRIP COVER LH

a.
B241356

Attach the 8 claws to install the assist grip cover.


Hide 69298A 41.INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B241355

Attach the 3 claws to install the door inside handle bezel.


Hide 42.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 43.INITIALIZE POWER WINDOW CONTROL SYSTEM

a.

Initialize the power window control system (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).