1.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
2.REMOVE FRONT SEAT ASSEMBLY (for RHD)
for Manual Seat:
Remove the front seat assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Manual Seat)>REMOVAL
for Power Seat:
Remove the front seat assembly.
Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY (for Power Seat)>REMOVAL
58810J
3.REMOVE CONSOLE BOX ASSEMBLY (for RHD)
for Automatic Transmission:
Remove the console box assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Automatic Transmission)>REMOVAL
for Manual Transmission:
Remove the console box assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX(for Manual Transmission)>REMOVAL
w/ Refrigerated Cool Box:
Remove the console box assembly.
Click hereVehicle Interior>INTERIOR PANELS / TRIM>FRONT CONSOLE BOX (w/ Refrigerated Cool Box)>REMOVAL
4.REMOVE REAR NO. 2 SEAT ASSEMBLY (w/ Rear No. 2 Seat)
for Manual Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Manual Seat Type LH Side)>REMOVAL
for Power Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY (for Power Seat Type LH Side)>REMOVAL
for Face to Face Seat Type:
Click hereVehicle Interior>SEAT>REAR NO. 2 SEAT ASSEMBLY(for Face to Face Seat Type)>REMOVAL
5.REMOVE REAR NO. 1 SEAT ASSEMBLY (w/ Rear No. 1 Seat)
for 60/40 Split Slide Walk-in Seat Type LH Side:
for 60/40 Split Slide Walk-in Seat Type RH Side:
6.REMOVE REAR NO. 1 SEATBACK ASSEMBLY (w/ Rear No. 1 Seat)
for 60/40 Split Double-folding Seat Type LH Side:
for 60/40 Split Double-folding Seat Type RH Side:
58371F
7.REMOVE REAR NO. 1 FLOOR STEP COVER (w/ Rear No. 2 Seat)
67934
8.REMOVE QUARTER SCUFF PLATE LH (w/ Rear No. 2 Seat)
67933
9.REMOVE QUARTER SCUFF PLATE RH (for RHD, w/ Rear No. 2 Seat)
Use the same procedure described for the LH side.
67918D
10.REMOVE REAR DOOR SCUFF PLATE LH
67917C
11.REMOVE REAR DOOR SCUFF PLATE RH (for RHD)
Use the same procedure described for the LH side.
62332C
12.REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH
64910M
13.REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
64717A
14.REMOVE FRONT LUGGAGE COMPARTMENT TRIM COVER (w/o Rear No. 2 Seat)
58401A
15.REMOVE NO. 1 DECK BOARD SUB-ASSEMBLY (w/o Rear No. 2 Seat)
58574A
16.REMOVE REAR FLOOR MAT REAR SUPPORT PLATE (w/o Rear No. 2 Seat)
57412C
17.REMOVE FLOOR SIDE RAIL LH (w/ Deck Rail)
57411D
18.REMOVE FLOOR SIDE RAIL RH (w/ Deck Rail)
Use the same procedure described for the LH side.
58570C
19.REMOVE REAR FLOOR CARPET ASSEMBLY (w/o Rear No. 2 Seat)
73233A
20.REMOVE REAR NO. 1 SEAT OUTER LAP BELT ANCHOR COVER
64725D
21.REMOVE NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
64937A
22.REMOVE NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
64712F
23.REMOVE FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
74617A
24.REMOVE ASSIST GRIP PLUG (w/ Rear No. 2 Seat)
74603C
25.REMOVE ASSIST GRIP SUB-ASSEMBLY (w/ Rear No. 2 Seat)
64740C
26.REMOVE DECK TRIM SIDE PANEL ASSEMBLY LH
62640P
27.REMOVE REAR QUARTER TRIM PANEL ASSEMBLY LH
67920
28.REMOVE DOOR SCUFF PLATE ASSEMBLY LH
67910
29.REMOVE DOOR SCUFF PLATE ASSEMBLY RH (for RHD)
77306
30.REMOVE FUEL LID LOCK OPEN LEVER SUB-ASSEMBLY
Detach the 3 claws.
Remove the fuel lid lock control cable assembly and fuel lid lock open lever sub-assembly.
58510D
31.REMOVE FRONT FLOOR CARPET ASSEMBLY
for LHD:
Detach the 6 clamps and fold back the front floor carpet assembly from the floor carpet hooks.
for RHD:
Detach the 12 clamps and fold back the front floor carpet assembly from the floor carpet hooks.
77035
32.REMOVE FUEL LID LOCK CONTROL CABLE SUB-ASSEMBLY
Turn the fuel lid lock control cable sub-assembly counterclockwise and remove the fuel lid lock control cable sub-assembly from the retainer.
Turn the lock retainer counterclockwise and remove the lock retainer.
for LHD:
Using a clip remover, detach the clamp labeled <A>.
Detach the 13 clamps and remove the fuel lid lock control cable sub-assembly.
for RHD:
Using a clip remover, detach the 3 clamps labeled <A>.
Detach the 14 clamps and remove the fuel lid lock control cable sub-assembly.