Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2017.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  C1422  Master Cylinder Pressure Sensor Zero Point High Malfunction  C1456  Control Pressure Sensor Zero Point High  


DESCRIPTION

Refer to DTCs C1421, C1423, C1424, C1455, C1457 and C1458 (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1281).

DTC Code DTC Detection Condition Trouble Area
C1422 When the stop light switch is off, the PM/C1 terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Master cylinder pressure sensor circuit

·

Master cylinder solenoid (Master cylinder pressure sensor)


C1456 When the stop light switch is off, the PCTRL terminal voltage is 0.86 V or higher for 5 seconds or more.
·

STOP fuse

·

Stop light switch assembly

·

Stop light switch circuit

·

Pressure control sensor circuit

·

Master cylinder solenoid (Pressure control sensor)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (master cylinder solenoid), perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

When DTC C1425 is output together with DTC C1422 and/or C1456, inspect and repair the trouble areas indicated by DTC C1425 first (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>C1425).


PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SW)

OK

2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION

NG

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
2.CHECK BRAKE PEDAL AND STOP LIGHT SWITCH ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check the brake pedal height and stop light switch assembly installation (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE PEDAL (for Hydraulic Brake Booster)>ADJUSTMENT).

OK:

The brake pedal height and stop light switch assembly installation are normal.




OK

3.RECONFIRM DTC

NG

ADJUST BRAKE PEDAL OR STOP LIGHT SWITCH ASSEMBLY

3.RECONFIRM DTC

b.

Start the engine.


c.

Drive the vehicle at a speed of 40 km/h (25 mph) or more and perform braking test (decelerate the vehicle by depressing the brake pedal).


d.

Check if the same DTC is output (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output (for LHD) B
DTC is output (for RHD) C



A

B

C

4.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.

Remove the stop light switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).


b.

Inspect the stop light switch assembly (See pageVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION).

OK:

The stop light switch assembly is normal.




OK

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.

Turn the ignition switch off.


b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP

Measure the resistance according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-7 (STP) - Body ground Brake pedal depressed 8 to 14 V
Brake pedal released Below 1.5 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))

Result
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR