Home › Vehicle Exterior › DOOR / HATCH › FRONT DOOR › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053744 DOOR / HATCH _0261247 FRONT DOOR A

DOOR / HATCH  FRONT DOOR  REASSEMBLY  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.

·

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS



PROCEDURE

Hide 67173 1.INSTALL BACK DOOR CUSHION

a.

Attach the clip to install a new door panel cushion.


Hide 75976G 3.INSTALL NO. 2 FRONT DOOR STRIPE LH

Hide 75986F 4.INSTALL FRONT DOOR OUTSIDE STRIPE LH

Hide 75756C 6.INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH

Hide 75712B 7.INSTALL FRONT DOOR BELT MOULDING LH

Hide 67862 8.INSTALL FRONT DOOR WEATHERSTRIP LH

a.
B238557

Attach the 21 clips to install a new front door weatherstrip LH.


Hide 68620 9.INSTALL FRONT DOOR CHECK ASSEMBLY LH

a.
B238556

Install the front door check assembly LH to the front door panel assembly with the 2 nuts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


b.

Apply adhesive to the threads of the bolt.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Install the front door check assembly LH with the bolt.

Torque:
27 N*m (275 kgf*cm, 20 ft.*lbf)


Hide 67924 10.INSTALL FRONT DOOR NO. 2 STIFFENER CUSHION

a.

Clean the installation surface.

i.

Using a heat light, heat the installation surface.

Standard:
Item Temperature
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.



ii.

Remove the double-sided tape from the installation surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new front door No. 2 stiffener cushion.

i.

Using a heat light, heat the front door No. 2 stiffener cushion and the installation surface.

HINT:

When installing the front door No. 2 stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.


Standard:
Item Temperature
Door stiffener cushion 20 to 30°C (68 to 86°F)
Vehicle body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the front door No. 2 stiffener cushion and vehicle body excessively.



ii.

Remove the peeling paper from the face of the front door No. 2 stiffener cushion.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



iii.

Attach the 2 clamps and double-sided tape to install the front door No. 2 stiffener cushion.

HINT:

Press the front door No. 2 stiffener cushion firmly to install it.



iv.

Install the 2 bolts.



Hide 69312 11.INSTALL FRONT DOOR LOCK OPEN ROD LH

a.
B241221N02
2.958,2.323 3.156,2.531 0.198,0.208 10 false (1) 2.167,1.906 2.365,2.115 0.198,0.208 10 true (2)

Install the front door lock open rod LH as indicated by the arrows in the order shown in the illustration.


Hide 82152A 12.INSTALL FRONT DOOR WIRE LH (w/ Smart Entry and Start System)

a.
B238552

Attach the 4 clamps to install the front door wire LH.


Hide 69202A 13.INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door outside handle frame sub-assembly LH.


b.
B241222

Attach the door handle nut and claw.


c.

Using a T30 "TORX" socket wrench, install the front door outside handle frame sub-assembly LH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


d.

w/ Entry and Start System:

i.
B238551

Attach the clamp.


ii.

Connect the front door wire LH connector.



Hide 69254C 14.INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH

a.

Attach the 2 claws to install the front door rear outside handle pad LH.


Hide 69252 15.INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

a.

Attach the 3 claws to install the front door front outside handle pad LH.


Hide 69220 16.INSTALL FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH

a.
B241223

Insert the front end of the front door outside handle assembly LH into the front door outside handle frame sub-assembly LH.


b.

Insert the rear end of the front door outside handle assembly LH into the front door outside handle frame sub-assembly LH, and then slide the front door outside handle assembly LH toward the front of the vehicle to install it.


c.
B241224

Move the lever in the direction indicated by the arrow in the illustration to lock the front door outside handle assembly LH.


d.
B238541

Connect the connector.


e.

Attach the 2 claws.


Hide 69760C 17.INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

a.

Install the front door inside locking cable assembly LH.


b.

Attach the 3 claws.


Hide 69720B 18.INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

a.

Install the front door lock remote control cable assembly LH.


Hide 69040A 19.INSTALL FRONT DOOR LOCK ASSEMBLY LH

Hide 69217D 20.INSTALL FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)

a.
B238540

Using a T30 "TORX" socket wrench, install the front door outside handle cover RH with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


b.
B241166

Install the hole plug.


Hide 69217D 21.INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)

a.
B241225

Attach the claw to install the front door outside handle cover LH to the lock cylinder assembly.


Hide 22.INSTALL FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)

a.

Install the front door outside handle cover with lock cylinder assembly.

HINT:

Make sure that the door lock cylinder rod is inserted into the front door lock assembly LH.



b.
B238538

Using a T30 "TORX" socket wrench, install the front door outside handle cover with lock cylinder assembly with the screw.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)


c.
B238537

Install the hole plug.


Hide 67404F 23.INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

a.
B241226

Install the front door rear lower frame sub-assembly LH with the bolt as shown in the illustration.


Hide 67664C 24.INSTALL DOOR FRAME GARNISH LH

a.
B238558

Attach the clip to install a new door frame garnish LH.


Hide 68151D 25.INSTALL FRONT DOOR GLASS RUN LH

a.
B238535

Install the front door glass run LH.


Hide 85720C 26.INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

Hide 69802 27.INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

a.

Apply MP grease to the sliding parts of the front door window regulator sub-assembly LH.


b.

Install the temporary bolt to the front door window regulator sub-assembly LH.


c.
B238533C03
2.094,1.354 1.885,1.354 true 1.667,1.281 1.917,1.531 0.25,0.25 10 true *1 2.25,2.25 2.5,2.5 0.25,0.25 10 true (6) 1.729,2.375 1.917,2.563 0.188,0.188 10 true (5) 1.833,1.083 2.083,1.333 0.25,0.25 10 true (4) 3.063,2.083 3.25,2.333 0.188,0.25 10 true (3) 3.052,1.302 3.25,1.5 0.198,0.198 10 true (2) 2.708,2.125 2.917,2.333 0.208,0.208 10 true (1)
*1 Temporary Bolt


Temporarily install the front door window regulator sub-assembly LH with the temporary bolt.


d.

Temporarily install the 5 bolts, and then tighten the temporary bolt and 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



e.

Connect the connector.


Hide 68102 28.INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

a.

Connect the cable to the negative (-) battery terminal.


b.

Connect the multiplex network master switch assembly and move the front door glass sub-assembly LH so that the door glass bolt installation locations can be seen.


c.

Disconnect the cable from the negative (-) battery terminal and multiplex network master switch assembly.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



d.
B241243N01
2.281,0.104 2.573,0.323 0.292,0.219 10 false (1) 0.375,0.063 0.604,0.281 0.229,0.219 10 true (2)

Insert the front door glass sub-assembly LH into the front door panel along the front door glass run LH as indicated by the arrows in the order shown in the illustration.


e.
B238531N02
1.688,1.885 1.938,2.125 0.25,0.24 10 true (1) 3.031,1.75 3.292,1.99 0.26,0.24 10 true (2)

Install the front door glass sub-assembly LH with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)

HINT:

Tighten the bolts in the order shown in the illustration.



Hide 87940 29.INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

Hide 67832 30.INSTALL FRONT DOOR SERVICE HOLE COVER LH

a.

Apply new butyl tape to the front door panel assembly LH.


b.
B238607C03
0.146,0.177 0.49,0.375 0.344,0.198 10 false *a 3.042,0.156 3.313,0.354 0.271,0.198 10 false *a
*a Reference Point


Pass the front door lock remote control cable assembly LH and front door inside locking cable assembly LH through a new front door service hole cover LH.


c.

Attach the front door service hole cover LH using the reference points on the front door panel assembly LH.

NOTICE:
·

There should be no wrinkles or folds after attaching the front door service hole cover LH.

·

After attaching the front door service hole cover LH, check the seal quality.



NOTICE:

Securely install the front door service hole cover LH preventing wrinkles and air bubbles.



d.
B238530

Attach the 2 clamps.


e.

Install the bolt to the front door wire LH.


Hide 89860A 31.INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

Hide 86160 32.INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

Hide 89430A 33.INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)

Hide 84927 34.INSTALL SEAT MEMORY SWITCH (w/ Seat Position Memory System)

Hide 69206B 35.INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

a.
B238527

Attach the guide and 2 claws to install the front door inside handle sub-assembly LH to the front door trim board sub-assembly LH.


b.

Install the 2 screws.


c.
B238529

Install the 8 screws to the door assist grip assembly LH.


Hide 84810 36.INSTALL POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)

Hide 84040 37.INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)

a.

Install the multiplex network master switch assembly with the 3 screws.


Hide 81080E 38.INSTALL FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)

Hide 81080L 39.INSTALL NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)

Hide 81910A 40.INSTALL FRONT REFLEX REFLECTOR ASSEMBLY

a.

Attach the 2 claws to install the front reflex reflector assembly.


Hide 68172A 41.INSTALL FRONT DOOR INNER GLASS WEATHERSTRIP LH

a.
B238605

Install the front door inner glass weatherstrip LH.


Hide 67602 42.INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH

a.
B241244

Connect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.


b.

Connect the 2 connectors.


c.

w/ Seat Position Memory System:

i.

Connect the connectors.



d.
B241251C01
1.063,3.51 1.25,3.229 1.25,3.229 1.49,3.229 true 1.552,3.167 1.865,3.365 0.313,0.198 10 false *a
*a Reference Boss


Attach the reference boss and front door trim board sub-assembly LH by attaching the 4 claws of the front door inner glass weatherstrip LH as shown in the illustration.


e.
B238522

Attach the 12 clips to install the front door trim board sub-assembly LH.


f.

Install the 3 screws.


Hide 74611C 43.INSTALL ASSIST GRIP COVER LH

a.
B241252

Attach the 8 claws to install the assist grip cover LH.


Hide 69298A 44.INSTALL NO. 2 DOOR INSIDE HANDLE BEZEL LH

a.
B241259

Attach the 3 claws to install the No. 2 door inside handle bezel LH.


Hide 67492A 45.INSTALL FRONT DOOR LOWER FRAME BRACKET GARNISH LH

a.

Attach the 2 claws to install the front door lower frame bracket garnish LH.


Hide 46.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


Hide 47.INITIALIZE POWER WINDOW CONTROL SYSTEM

Hide 48.CHECK SRS WARNING LIGHT

Hide 86790C 49.ADJUST SIDE TELEVISION CAMERA ASSEMBLY (w/ Side Monitor System)