Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  C1A4B  Stop Light Relay Circuit  


DESCRIPTION

·

for 2TR-FE:

The brake actuator assembly outputs stop light signals to the stop light switch assembly. When the brake actuator assembly detects a malfunction relating to the stop light circuit, the driving support ECU is notified via CAN communication, and C1A4B is output.

·

except 2TR-FE:

The master cylinder solenoid outputs stop light signals to the stop light switch assembly. When the master cylinder solenoid detects a malfunction relating to the stop light circuit, the driving support ECU is notified via CAN communication, and C1A4B is output.


DTC No. Detection Item DTC Detection Condition Trouble Area
C1A4B Stop Light Relay Circuit Diagnosis Condition:
·

+BI1 and +BI2 terminal voltage is 8.9 V or higher


Malfunction status:
Either of the following occurs
·

When STPO is ON and STP is OFF, STP2 is OFF continuously for 0.3 seconds or more

·

When STPO is OFF and STP and STP2 input signal statuses differ continuously for 0.3 seconds or more


·

Skid control ECU assembly (brake actuator assembly) (for 2TR-FE)

·

Skid control ECU assembly (master cylinder solenoid) (except 2TR-FE)

·

Harness or connector

·

Rear combination light assembly LH

·

Rear combination light assembly RH

·

Center stop light assembly

·

Stop light switch assembly

·

Shift lock control ECU (transmission floor shift assembly)

·

ECM

·

Transmission control ECU assembly (for 1KD-FTV)

·

Certification ECU (smart key ECU assembly)



WIRING DIAGRAM

C384435E01
2.229,0.333 2.615,0.531 0.385,0.198 10 false STP 2.698,0.135 2.927,0.333 0.229,0.198 10 false 4 2.563,0.344 2.948,0.542 0.385,0.198 10 false G150 2.646,0.563 3.031,0.76 0.385,0.198 10 false *1 0.063,0.719 3.417,1.094 3.354,0.375 10 false Shift Lock Control ECU (Transmission Floor Shift Assembly) 3.073,0.135 3.313,0.385 0.24,0.25 10 false 6 2.979,0.344 3.396,0.542 0.417,0.198 10 false G45 3.042,0.563 3.25,0.75 0.208,0.188 10 false *2 4.302,0.135 4.531,0.333 0.229,0.198 10 false 35 4.708,0.125 4.927,0.323 0.219,0.198 10 false 8 5.063,0.135 5.375,0.333 0.313,0.198 10 false 10 5.427,0.125 5.813,0.323 0.385,0.198 10 false 13 5.76,0.375 6.146,0.573 0.385,0.198 10 false STP 5.354,0.344 5.833,0.563 0.479,0.219 10 false G185 4.969,0.344 5.396,0.563 0.427,0.219 10 false G180 4.625,0.344 5.01,0.542 0.385,0.198 10 false G57 4.25,0.344 4.635,0.542 0.385,0.198 10 false G56 4.313,0.552 4.51,0.771 0.198,0.219 10 false *3 4.698,0.552 4.927,0.75 0.229,0.198 10 false *4 5.094,0.552 5.479,0.75 0.385,0.198 10 false *9 5.458,0.552 5.781,0.792 0.323,0.24 10 false *6 5.781,0.75 6.229,0.948 0.448,0.198 10 false ECM 5.76,1.396 6.323,1.615 0.563,0.219 10 false STP1 5.542,1.26 5.802,1.438 0.26,0.177 10 false 2 4.25,1.625 4.667,1.823 0.417,0.198 10 false G213 4.271,1.823 7.135,2.042 2.865,0.219 10 false Certification ECU (Smart Key ECU Assembly) 3.313,1.281 3.635,1.521 0.323,0.24 10 false 14 2.927,1.406 3.25,1.646 0.323,0.24 10 false STP 2.031,1.781 2.438,2.01 0.406,0.229 10 false G70 2.042,1.958 2.635,2.156 0.594,0.198 10 false TCM*4 0.729,2.021 1.615,2.219 0.885,0.198 10 false from Battery 0.958,3.25 1.448,3.448 0.49,0.198 10 false STOP 1.542,2.958 1.76,3.156 0.219,0.198 10 false 7 1.792,2.958 2.031,3.177 0.24,0.219 10 false B 3.135,2.646 3.396,2.844 0.26,0.198 10 false L 3.375,2.646 3.604,2.854 0.229,0.208 10 false 3 4.24,2.542 4.563,2.781 0.323,0.24 10 false 45 4.229,2.771 4.552,3.01 0.323,0.24 10 false A7 4.26,2.979 4.521,3.198 0.26,0.219 10 false *5 4.615,2.531 4.917,2.75 0.302,0.219 10 false 22 4.604,2.771 4.927,3.01 0.323,0.24 10 false A6 4.625,2.969 4.948,3.208 0.323,0.24 10 false *9 4.938,2.656 5.458,2.896 0.521,0.24 10 false STP2 4.948,3.563 5.375,3.76 0.427,0.198 10 false STPO 4.604,3.448 4.927,3.688 0.323,0.24 10 false 31 4.594,3.667 4.917,3.906 0.323,0.24 10 false A6 4.615,3.865 4.938,4.104 0.323,0.24 10 false *9 4.219,3.448 4.542,3.688 0.323,0.24 10 false 16 4.229,3.667 4.552,3.906 0.323,0.24 10 false A7 4.25,3.875 4.573,4.115 0.323,0.24 10 false *5 3.375,3.573 3.698,3.813 0.323,0.24 10 false 4 2.938,3.573 3.385,3.781 0.448,0.208 10 false ACC 1.552,4.542 1.875,4.781 0.323,0.24 10 false 2 1.781,4.542 2.104,4.781 0.323,0.24 10 false GND 1.667,5.146 1.99,5.385 0.323,0.24 10 false A99 1.667,5.292 3.615,5.479 1.948,0.188 10 false Stop Light Switch Assembly 2.938,4.542 3.26,4.781 0.323,0.24 10 false OUT 3.375,4.542 3.698,4.781 0.323,0.24 10 false 1 4.26,4.448 4.583,4.688 0.323,0.24 10 false 7 4.646,4.448 4.969,4.688 0.323,0.24 10 false 2 4.594,4.677 4.917,4.917 0.323,0.24 10 false A6 4.219,4.677 4.542,4.917 0.323,0.24 10 false A7 4.24,4.896 4.563,5.135 0.323,0.24 10 false *5 4.604,4.885 4.927,5.125 0.323,0.24 10 false *9 4.958,4.573 5.281,4.813 0.323,0.24 10 false STP 3.948,5.302 6.927,5.531 2.979,0.229 10 false Skid Control ECU (Brake Actuator Assembly)*9 4.563,6.708 6.552,6.938 1.99,0.229 10 false Driving Support ECU Assembly 4.76,7.125 4.979,7.323 0.219,0.198 10 false 2 6.156,7.135 6.479,7.375 0.323,0.24 10 false 1 4.927,7.677 5.25,7.917 0.323,0.24 10 false Z1 4.917,7.823 6.688,8.021 1.771,0.198 10 false Center Stop Light Assembly 3.354,7.052 3.677,7.292 0.323,0.24 10 false 1 3.271,7.271 3.594,7.51 0.323,0.24 10 false R21 3.333,7.49 3.656,7.729 0.323,0.24 10 false *8 2.99,7.063 3.313,7.302 0.323,0.24 10 false 1 2.917,7.271 3.24,7.51 0.323,0.24 10 false Q31 2.979,7.479 3.302,7.719 0.323,0.24 10 false *7 2.552,7.146 2.875,7.385 0.323,0.24 10 false STP 1.823,7.146 2.146,7.385 0.323,0.24 10 false E 1.552,7.156 1.875,7.396 0.323,0.24 10 false 4 1.469,6.365 1.792,6.542 0.323,0.177 10 false R22 1.458,6.604 3.844,6.792 2.385,0.188 10 false Rear Combination Light Assembly LH 1.563,5.865 1.885,6.104 0.323,0.24 10 false 4 1.823,5.875 2.146,6.115 0.323,0.24 10 false E 2.563,5.865 2.885,6.104 0.323,0.24 10 false STP 2.948,5.854 3.271,6.094 0.323,0.24 10 false 1 0.104,8.271 2.271,8.458 2.167,0.188 10 false *1: w/o Entry and Start System 0.104,8.531 2.427,8.76 2.323,0.229 10 false *2: w/ Entry and Start System 2.104,8.281 3.167,8.479 1.063,0.198 10 false *3: for 1GR-FE 2.104,8.521 3.167,8.708 1.063,0.188 10 false *4: for 1KD-FTV 3.177,8.26 4.458,8.438 1.281,0.177 10 false *5: except 2TR-FE 3.188,8.51 4.635,8.667 1.448,0.156 10 false *6: for 1GD-FTV 4.479,8.25 5.469,8.479 0.99,0.229 10 false *7: for 3 Door 5.417,8.25 6.729,8.438 1.313,0.188 10 false *9: for 2TR-FE 4.49,8.51 5.51,8.729 1.021,0.219 10 false *8: for 5 Door 1.469,7.729 3.854,7.917 2.385,0.188 10 false Rear Combination Light Assembly RH 3.958,5.677 6.938,5.885 2.979,0.208 10 false Skid Control ECU (Master Cylinder Solenoid)*5

CAUTION / NOTICE / HINT

NOTICE:

First perform the communication function inspections in How to Proceed with Troubleshooting to confirm that there are no CAN communication malfunctions before troubleshooting.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STP2, STPO AND STP TERMINAL)
a.

Turn the engine switch off.


b.
U148916C01
0.865,0.219 0.99,0.219 0.99,0.219 1.292,0.885 true 1.677,1.927 1.802,1.927 1.802,1.927 1.958,1.344 true 2.604,0.167 2.469,0.167 2.469,0.167 2.177,1.177 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 2.74,0.094 3.198,0.292 0.458,0.198 10 false STP2 0.563,0.146 1.021,0.344 0.458,0.198 10 false STP 1.24,1.865 1.698,2.063 0.458,0.198 10 false STPO 0.146,0.073 0.458,0.271 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


U148398C02
1.948,0.604 1.688,1.146 true 2.875,0.604 2.635,1.135 true 2.531,1.521 2.344,1.865 true 1.031,0.646 1.229,0.813 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.156,1.906 2.563,2.073 0.406,0.167 10 false STP2 1.865,0.396 2.219,0.573 0.354,0.177 10 false STP 2.729,0.396 3.177,0.573 0.448,0.177 10 false STPO
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



c.

for 2TR-FE:

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


d.

except 2TR-FE:

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for 2TR-FE:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A6-31 (STPO) - Body ground Always 11 to 14 V
A6-22 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-22 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V

except 2TR-FE:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V
A7-16 (STPO) - Body ground Always 11 to 14 V
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



g.

except 2TR-FE:

Connect the A7 skid control ECU (master cylinder solenoid) connector.


h.

for 2TR-FE:

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Result Proceed to
All terminal voltages are normal A
Only STP2 terminal voltage abnormal (for 2TR-FE) B
Only STP2 terminal voltage abnormal (except 2TR-FE) C
Only STPO terminal voltage abnormal (for 2TR-FE) D
Only STPO terminal voltage abnormal (except 2TR-FE) E
Only STP terminal voltage abnormal (for 2TR-FE) F
Only STP terminal voltage abnormal (except 2TR-FE) G
STPO terminal and STP terminal voltage abnormal H



A

2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)

B

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)

C

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SMART KEY ECU ASSEMBLY)

D

17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

E

18.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

F

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)

G

24.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY LH)

H

29.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
2.PERFORM ACTIVE TEST USING GTS (STOP LIGHT RELAY)
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on

OK:

Stop light turns ON/OFF in response to the GTS operation



Result:
Proceed to
OK
NG (for 2TR-FE)
NG (except 2TR-FE)



OK

3.CHECK FOR DTC

NG (for 2TR-FE)

4.INSPECT BRAKE ACTUATOR ASSEMBLY

NG (except 2TR-FE)

5.INSPECT MASTER CYLINDER SOLENOID
3.CHECK FOR DTC

b.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on


c.

According to the display on the GTS, perform the Active Test.



Result:
Result Proceed to
C1380 is output (for 2TR-FE) A
C1380 is output (except 2TR-FE) B
C1380 is not output C



A

B

C

4.INSPECT BRAKE ACTUATOR ASSEMBLY
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on


b.
E233300C84
1.427,0.271 1.917,0.563 0.49,0.292 1.688,1.115 1.167,1.677 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A99 1,1.698 1.448,1.958 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-4 (ACC) - Body ground Active Test is on Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

5.INSPECT MASTER CYLINDER SOLENOID
a.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
Stop Light Relay Stop light control relay (Stop light switch assembly) Relay OFF/ON Stop lights come on


b.
E233300C84
1.427,0.271 1.917,0.563 0.49,0.292 1.688,1.115 1.167,1.677 true 0.188,0.115 0.417,0.281 0.229,0.167 10 false *a 1.542,0.333 1.99,0.594 0.448,0.26 10 false A99 1,1.698 1.448,1.958 0.448,0.26 10 false ACC
*a Component with harness connected
(Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-4 (ACC) - Body ground Active Test is on Below 1.5 V



Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

6.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - SMART KEY ECU ASSEMBLY)
a.
U148916C03
2.615,0.146 2.448,0.146 2.448,0.146 2.177,1.146 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 2.677,0.073 3.135,0.271 0.458,0.198 10 false STP2 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-22 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-22 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



f.

Connect the G213 certification ECU (smart key ECU assembly) connector.


g.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
7.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ECM)
a.
U148916C03
2.615,0.146 2.448,0.146 2.448,0.146 2.177,1.146 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 2.677,0.073 3.135,0.271 0.458,0.198 10 false STP2 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G180 ECM connector.


e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-22 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-22 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



g.

Connect the G180 ECM connector.


h.

Connect the G213 certification ECU (smart key ECU assembly) connector.


i.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

NG

8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRANSMISSION FLOOR SHIFT ASSEMBLY)
8.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
U148916C03
2.615,0.146 2.448,0.146 2.448,0.146 2.177,1.146 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 2.677,0.073 3.135,0.271 0.458,0.198 10 false STP2 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G180 ECM connector.


e.

Disconnect the G150 shift lock control ECU (transmission floor shift assembly) connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-22 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-22 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



h.

Connect the G150 shift lock control ECU (transmission floor shift assembly) connector.


i.

Connect the G180 ECM connector.


j.

Connect the G213 certification ECU (smart key ECU assembly) connector.


k.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE TRANSMISSION FLOOR SHIFT ASSEMBLY

NG

9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
9.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
U148916C03
2.615,0.146 2.448,0.146 2.448,0.146 2.177,1.146 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 2.677,0.073 3.135,0.271 0.458,0.198 10 false STP2 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G180 ECM connector.


e.

Disconnect the G150 shift lock control ECU (transmission floor shift assembly) connector.


f.

Disconnect the A99 stop light switch assembly connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-22 (STP2) - Body ground Always Below 1.5 V



i.

Connect the A99 stop light switch assembly connector.


j.

Connect the G150 shift lock control ECU (transmission floor shift assembly) connector.


k.

Connect the G180 ECM connector.


l.

Connect the G213 certification ECU (smart key ECU assembly) connector.


m.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-22 (STP2) - A99-3 (L) Always Below 1 Ω
A6-22 (STP2) or A99-3 (L) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - SMART KEY ECU ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



f.

Connect the G213 certification ECU (smart key ECU assembly) connector.


g.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE SMART KEY ECU ASSEMBLY

NG

12.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - ECM)
12.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - ECM)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



g.

Connect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



h.

Connect the G213 certification ECU (smart key ECU assembly) connector.


i.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

NG

13.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TRANSMISSION FLOOR SHIFT ASSEMBLY)
13.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TRANSMISSION FLOOR SHIFT ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



e.

Disconnect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



h.

Connect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



i.

Connect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



j.

Connect the G213 certification ECU (smart key ECU assembly) connector.


k.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG (for 1KD-FTV (for Automatic Transmission))
NG (except 1KD-FTV (for Automatic Transmission))



OK

NG (for 1KD-FTV (for Automatic Transmission))

14.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TCM)

NG (except 1KD-FTV (for Automatic Transmission))

15.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - TCM)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



e.

Disconnect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

Disconnect the G70 TCM connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-45 (STP2) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



i.

Connect the G70 TCM connector.


j.

Connect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



k.

Connect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



l.

Connect the G213 certification ECU (smart key ECU assembly) connector.


m.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

NG

15.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
15.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.
U148398C03
2.542,1.542 2.771,1.875 false 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.656,1.917 3.063,2.083 0.406,0.167 10 false STP2
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the G213 certification ECU (smart key ECU assembly) connector.


d.

Disconnect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



e.

Disconnect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



f.

for 1KD-FTV:

Disconnect the G70 TCM connector.


g.

Disconnect the A99 stop light switch assembly connector.


h.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



i.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-45 (STP2) - Body ground Always Below 1.5 V



j.

Connect the A99 stop light switch assembly connector.


k.

for 1KD-FTV:

Connect the G70 TCM connector.


l.

Connect the G150*1 or G45*2 shift lock control ECU (transmission floor shift assembly) connector.

*1: w/o Entry and Start System

*2: w/ Entry and Start System



m.

Connect the G56*1, G57*2 or G185*3 ECM connector.

*1: for 1GR-FE

*2: for 1KD-FTV

*3: for 1GD-FTV



n.

Connect the G213 certification ECU (smart key ECU assembly) connector.


o.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

16.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-45 (STP2) - A99-3 (L) Always Below 1 Ω
A7-45 (STP2) or A99-3 (L) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the A99 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-31 (STPO) - A99-4 (ACC) Always Below 1 Ω



f.

Connect the A99 stop light switch assembly connector.


g.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

18.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the A99 stop light switch assembly connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STPO) - A99-4 (ACC) Always Below 1 Ω



f.

Connect the A99 stop light switch assembly connector.


g.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
U148916C02
0.896,0.198 1.021,0.198 1.021,0.198 1.281,0.865 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 0.583,0.115 1.042,0.313 0.458,0.198 10 false STP 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



f.

Connect the R22 rear combination light assembly LH connector.


g.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

20.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
20.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
U148916C02
0.896,0.198 1.021,0.198 1.021,0.198 1.281,0.865 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 0.583,0.115 1.042,0.313 0.458,0.198 10 false STP 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



g.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



h.

Connect the R22 rear combination light assembly LH connector.


i.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

21.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT SET)
21.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - CENTER STOP LIGHT SET)
a.
U148916C02
0.896,0.198 1.021,0.198 1.021,0.198 1.281,0.865 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 0.583,0.115 1.042,0.313 0.458,0.198 10 false STP 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Disconnect the Z1 center stop light assembly connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A6-2 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



h.

Connect the Z1 center stop light assembly connector.


i.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



j.

Connect the R22 rear combination light assembly LH connector.


k.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

NG

22.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
22.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.
U148916C02
0.896,0.198 1.021,0.198 1.021,0.198 1.281,0.865 true 0.281,0.938 0.594,1.135 0.313,0.198 10 false A6 0.583,0.115 1.042,0.313 0.458,0.198 10 false STP 0.146,0.125 0.604,0.323 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Skid Control ECU (Brake Actuator Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Disconnect the Z1 center stop light assembly connector.


f.

Disconnect the A99 stop light switch assembly connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A6-2 (STP) - Body ground Always Below 1.5 V



i.

Connect the A99 stop light switch assembly connector.


j.

Connect the Z1 center stop light assembly connector.


k.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



l.

Connect the R22 rear combination light assembly LH connector.


m.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

23.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-1 (OUT) - A6-2 (STP) Always Below 1 Ω
A99-1 (OUT) or A6-2 (STP) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

24.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY LH)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



f.

Connect the R22 rear combination light assembly LH connector.


g.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY LH

NG

25.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY RH)
25.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - REAR COMBINATION LIGHT ASSEMBLY RH)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



g.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



h.

Connect the R22 rear combination light assembly LH connector.


i.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE REAR COMBINATION LIGHT ASSEMBLY RH

NG

26.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - CENTER STOP LIGHT SET)
26.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - CENTER STOP LIGHT SET)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Disconnect the Z1 center stop light assembly connector.


f.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



g.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 11 to 14 V*
A7-7 (STP) - Body ground Stop light switch assembly off (Brake pedal released) Below 1.5 V


HINT:

*: The minimum voltage value varies depending on the +BS terminal voltage value. The minimum voltage is 85% or more of the +BS terminal voltage.



h.

Connect the Z1 center stop light assembly connector.


i.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



j.

Connect the R22 rear combination light assembly LH connector.


k.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

NG

27.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
27.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.
U148398C01
2.229,0.729 1.688,1.135 true 1.021,0.635 1.219,0.802 0.198,0.167 10 false A7 0.125,0 2.552,0.354 2.427,0.354 10 false *a 2.302,0.625 2.708,0.792 0.406,0.167 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


c.

Disconnect the R22 rear combination light assembly LH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Disconnect the Z1 center stop light assembly connector.


f.

Disconnect the A99 stop light switch assembly connector.


g.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



h.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A7-7 (STP) - Body ground Always Below 1.5 V



i.

Connect the A99 stop light switch assembly connector.


j.

Connect the Z1 center stop light assembly connector.


k.

Connect the Q31*1 or R21*2 rear combination light assembly RH connector.

*1: for 3 Door

*2: for 5 Door



l.

Connect the R22 rear combination light assembly LH connector.


m.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

28.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-1 (OUT) - A7-7 (STP) Always Below 1 Ω
A99-1 (OUT) or A7-7 (STP) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

29.CHECK STOP LIGHT SWITCH ASSEMBLY POWER SOURCE CIRCUIT
a.
E360372C15
1.427,0.333 1.927,0.583 0.5,0.25 1.323,1.188 1.042,1.75 true 2.25,1.188 2.583,1.75 true 0.083,0.063 0.396,0.219 0.313,0.156 10 false *a 1.552,0.375 2.01,0.531 0.458,0.156 10 false A99 0.844,1.76 1.26,1.958 0.417,0.198 10 false GND 2.552,1.76 2.969,1.958 0.417,0.198 10 false B
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A99 stop light switch assembly connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A99-2 (GND) - Body ground Always Below 1 Ω



e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A99-7 (B) - Body ground Always 11 to 14 V



f.

Connect the A99 stop light switch assembly connector.


Result:
Proceed to
OK (for 2TR-FE)
OK (except 2TR-FE)
NG



OK (for 2TR-FE)

30.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)

OK (except 2TR-FE)

31.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

30.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A6 skid control ECU (brake actuator assembly) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A6-31 (STPO) or A99-4 (ACC) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A6 skid control ECU (brake actuator assembly) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK HARNESS AND CONNECTOR (MASTER CYLINDER SOLENOID - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A7 skid control ECU (master cylinder solenoid) connector.


b.

Disconnect the A99 stop light switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-16 (STPO) or A99-4 (ACC) - Body ground Always 10 kΩ or higher



d.

Connect the A99 stop light switch assembly connector.


e.

Connect the A7 skid control ECU (master cylinder solenoid) connector.


Result:
Proceed to
OK
NG



OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR