Home › Vehicle Interior › PRE-CRASH SAFETY › PRE-CRASH SAFETY SYSTEM › 2017.08–2020.08
RM27T0E _58 Vehicle Interior _053736 PRE-CRASH SAFETY _0261101 PRE-CRASH SAFETY SYSTEM C

PRE-CRASH SAFETY  PRE-CRASH SAFETY SYSTEM  U1104  Lost Communication with Driving Support ECU  


DESCRIPTION

·

for 2TR-FE:

The driving support ECU assembly is connected to the millimeter wave radar sensor assembly, forward recognition camera and skid control ECU (brake actuator assembly) via CAN communication. If communication with the millimeter wave radar sensor assembly, forward recognition camera or skid control ECU (brake actuator assembly) stops, the driving support ECU assembly stores DTC U1104.

·

except 2TR-FE:

The driving support ECU assembly is connected to the millimeter wave radar sensor assembly, forward recognition camera and skid control ECU (master cylinder solenoid) via CAN communication. If communication with the millimeter wave radar sensor assembly, forward recognition camera or skid control ECU (master cylinder solenoid) stops, the driving support ECU assembly stores DTC U1104.


DTC No. Detection Item DTC Detection Condition Trouble Area
U1104 Lost Communication with Driving Support ECU Any of the following conditions is met:
·

When the ignition switch is ON, a communication error between the driving support ECU assembly and the millimeter wave radar sensor assembly is detected for approximately 0.2 seconds.

·

When the ignition switch is ON, a communication error between the driving support ECU assembly and the forward recognition camera is detected for approximately 0.3 seconds.

·

for 2TR-FE:

When the ignition switch is ON, a communication error between the driving support ECU assembly and the skid control ECU (brake actuator assembly) is detected for approximately 1.5 seconds.

·

except 2TR-FE:

When the ignition switch is ON, a communication error between the driving support ECU assembly and the skid control ECU (master cylinder solenoid) is detected for approximately 1.5 seconds.


·

CAN communication system

·

Millimeter wave radar sensor assembly

·

Forward recognition camera

·

Skid control ECU assembly (brake actuator assembly) (for 2TR-FE)

·

Skid control ECU assembly (master cylinder solenoid) (except 2TR-FE)

·

Driving support ECU assembly

·

Harness or connector

·

Forward recognition camera system

·

Vehicle stability control system



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.

·

If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)

·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle. As a result, a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

Confirm that the connectors are securely connected, as a partially connected connector can cause this DTC to be stored.



PROCEDURE

1.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

Result:
Result Proceed to
DTC U1104 and other DTCs are output A
Only DTC U1104 is output B



A

B

2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)
2.CHECK FOR DTCs (FORWARD RECOGNITION CAMERA SYSTEM)

Result:
Result Proceed to
Forward recognition camera system DTCs are not output A
Forward recognition camera system DTCs are output B



A

3.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

B

3.CHECK FOR DTCs (VEHICLE STABILITY CONTROL SYSTEM)

Result:
Result Proceed to
Vehicle stability control system DTC are not output A
Vehicle stability control system DTC are output (for 2TR-FE) B
Vehicle stability control system DTC are output (except 2TR-FE) C



A

4.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)

B

C

4.TEST MODE INSPECTION (VEHICLE STABILITY CONTROL SYSTEM)
HINT:
·

for 2TR-FE:

When entering test mode, the brake actuator assembly communicates with the driving support ECU assembly to judge whether the vehicle is equipped with the pre-crash safety system. Therefore, do not exit test mode within 5 seconds of entering test mode.

·

except 2TR-FE:

When entering test mode, the master cylinder solenoid communicates with the driving support ECU assembly to judge whether the vehicle is equipped with the pre-crash safety system. Therefore, do not exit test mode within 5 seconds of entering test mode.



a.

Procedure to Enter Test Mode (Signal Check)

i.

Turn the ignition switch ON.


ii.

Change the shift state to park (P).


iii.

Check that the steering wheel is centered.


iv.

Turn the ignition switch off.


v.

Connect the GTS to the DLC3.


vi.

Turn the ignition switch ON.


vii.

Check that the parking brake is released.


viii.

Turn the GTS on.


ix.

for 2TR-FE:

Switch the skid control ECU (brake actuator assembly) to Test Mode (Signal Check) using the GTS.


x.

except 2TR-FE:

Switch the skid control ECU (master cylinder solenoid) to Test Mode (Signal Check) using the GTS.


xi.

Enter the following menus: Chassis / ABS/VSC/TRC / Utility / Signal Check.

HINT:

Do not exit test mode within 5 seconds of entering test mode. If test mode is exited within 5 seconds of entering test mode, DTC U1104 may be stored. If DTC U1104 is output after exiting test mode, enter test mode again, wait at least 5 seconds, then recheck for DTCs.




b.

Test Mode (Signal Check) Display Check

i.

Check that the ABS warning, brake warning / yellow (minor malfunction) and slip indicator lights come on for several seconds and then blink in the Test Mode pattern.

HINT:

If the ABS warning light, brake warning light / yellow (minor malfunction) or slip indicator light remains illuminated or does not illuminate when Test Mode (Signal Check) is entered, a component or wire harness may be malfunctioning.




c.

End of Test Mode (Signal Check)

i.

Turn the ignition switch off and disconnect the GTS.



Result:
Proceed to
NEXT



NEXT

5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
5.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END

B

6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
6.REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.

Replace the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>REMOVAL


b.

Adjust the millimeter wave radar sensor assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT


Result:
Proceed to
NEXT



NEXT

7.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
7.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (MILLIMETER WAVE RADAR SENSOR ASSEMBLY WAS DEFECTIVE)

B

8.REPLACE DRIVING SUPPORT ECU ASSEMBLY
8.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly.

Click hereEngine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL


Result:
Proceed to
NEXT



NEXT

9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
9.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output B



A

END (DRIVING SUPPORT ECU ASSEMBLY WAS DEFECTIVE)

B

10.REPLACE FORWARD RECOGNITION CAMERA
10.REPLACE FORWARD RECOGNITION CAMERA
a.

Replace the forward recognition camera.

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>REMOVAL


b.

Result:
Proceed to
NEXT



NEXT

11.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)
11.CHECK FOR DTCs (PRE-CRASH SAFETY SYSTEM)

b.

Make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system cannot detect the malfunction.




Result:
Result Proceed to
DTC U1104 is not output A
DTC U1104 is output (for 2TR-FE) B
DTC U1104 is output (except 2TR-FE) C



A

END (FORWARD RECOGNITION CAMERA WAS DEFECTIVE)

B

12.REPLACE BRAKE ACTUATOR ASSEMBLY

C

13.REPLACE MASTER CYLINDER SOLENOID
12.REPLACE BRAKE ACTUATOR ASSEMBLY
a.

Replace the brake actuator assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

END (BRAKE ACTUATOR ASSEMBLY WAS DEFECTIVE)

13.REPLACE MASTER CYLINDER SOLENOID

Result:
Proceed to
NEXT



NEXT

END (MASTER CYLINDER SOLENOID)