Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE UNIT › 2017.08–2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260522 ENGINE UNIT A

1GD-FTV ENGINE MECHANICAL  ENGINE UNIT  DISASSEMBLY  


PROCEDURE

Hide 29300 1.REMOVE VACUUM PUMP ASSEMBLY

a.
A456459

Remove the 3 bolts and vacuum pump assembly from the cylinder head sub-assembly.


b.

Remove the 2 O-rings from the vacuum pump assembly.


Hide 11382C 2.REMOVE CAMSHAFT OIL SEAL RETAINER

a.
A343511

Remove the camshaft oil seal retainer from the No. 3 camshaft bearing cap and cylinder head sub-assembly.


Hide 12281A 3.REMOVE NO. 1 ENGINE HANGER

a.
A343515

Remove the 2 bolts and No. 1 engine hanger from the cylinder head sub-assembly.


Hide 12582 4.REMOVE NO. 2 CYLINDER BLOCK INSULATOR

a.
A347339

Remove the No. 2 cylinder block insulator from the front No. 1 engine mounting bracket LH.


Hide 5.INSTALL FRONT NO. 1 ENGINE MOUNTING BRACKET LH

a.
A347340

Remove the 4 bolts and front No. 1 engine mounting bracket LH from the cylinder block sub-assembly.


Hide 12583A 6.REMOVE NO. 3 CYLINDER BLOCK INSULATOR

a.
A347341

Remove the No. 3 cylinder block insulator from the cylinder block sub-assembly.


Hide 12501 7.REMOVE GENERATOR BRACKET SUB-ASSEMBLY

a.
A343519

Remove the 4 bolts and generator bracket sub-assembly from the cylinder head sub-assembly and timing chain case assembly.


Hide 12311 10.REMOVE FRONT NO. 1 ENGINE MOUNTING BRACKET RH

a.
A347342

Remove the 4 bolts and front No. 1 engine mounting bracket RH from the cylinder block sub-assembly.


Hide 83530 11.REMOVE ENGINE OIL PRESSURE SWITCH ASSEMBLY

Hide 15600A 14.REMOVE OIL FILTER UNION

a.
A343521

Using a 27 mm deep socket wrench, remove the oil filter union from the oil filter bracket.


Hide 15677 15.REMOVE OIL FILTER BRACKET

a.
A343522

Remove the bolt, 2 nuts and oil filter bracket from the cylinder block sub-assembly.


b.

Remove the 2 O-rings from the cylinder block sub-assembly.


Hide 23760 16.REMOVE NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 12108 20.REMOVE OIL FILLER CAP SUB-ASSEMBLY

a.

Remove the oil filler cap sub-assembly from the cylinder head cover sub-assembly.


Hide 12108A 21.REMOVE OIL FILLER CAP GASKET

a.

Remove the oil filler cap gasket from the oil filler cap sub-assembly.


Hide 11201 22.REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Hide 12585 23.REMOVE NO. 5 CYLINDER BLOCK INSULATOR

a.
A343523

Remove the No. 5 cylinder block insulator from the cylinder block sub-assembly.


Hide 12581A 24.REMOVE NO. 1 CYLINDER BLOCK INSULATOR

a.
A343524

Remove the No. 1 cylinder block insulator from the cylinder block sub-assembly.


Hide 25.REMOVE CRANKSHAFT POSITION SENSOR HARNESS BRACKET

a.
A347344

Disconnect the crankshaft position sensor connector.


b.

Remove the bolt and crankshaft position sensor harness bracket from the cylinder block sub-assembly.


Hide 12102A 27.REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

Hide 15104 30.REMOVE OIL STRAINER SUB-ASSEMBLY

a.
A347345

Remove the 5 bolts, oil strainer sub-assembly and gasket from the cylinder block sub-assembly.


Hide 11381 31.REMOVE REAR ENGINE OIL SEAL RETAINER

a.
A343527

Remove the 5 bolts.


b.
A343528

Remove the rear engine oil seal retainer by prying between the rear engine oil seal retainer and cylinder block sub-assembly with a screwdriver.

NOTICE:

Be careful not to damage the contact surfaces of the cylinder block sub-assembly.


HINT:

Tape the screwdriver tip before use.



Hide 11381A 32.REMOVE REAR ENGINE OIL SEAL

a.
A343529E01
0.359,1.569 0.544,1.724 0.185,0.155 10 *a 0.574,1.682 1.055,1.682 false 2.741,1.225 2.926,1.380 0.185,0.155 10 *a 2.248,1.338 2.729,1.338 false

Place the rear engine oil seal retainer on wooden blocks.

Text in Illustration
*a Wooden Block


b.

Using a screwdriver, tap out the rear engine oil seal from the rear engine oil seal retainer.

NOTICE:

Do not damage the surface of the rear engine oil seal press fit hole.


HINT:

Tape the screwdriver tip before use.



Hide 34.SET NO. 1 CYLINDER TO TDC/COMPRESSION

a.

Temporarily install the crankshaft pulley and crankshaft pulley set bolt to the crankshaft.


b.
A347371E01
0.604,1.99 0.813,1.99 0.813,1.99 1.49,1.365 true 1.594,1.365 1.594,1.979 true 1.01,3.313 1.01,3.927 true 2.219,3.313 2.219,3.927 true 0.396,1.875 0.583,2.031 0.188,0.156 10 false *a 1.521,1.99 1.802,2.198 0.281,0.208 10 true *a 0.906,3.938 1.146,4.146 0.24,0.208 10 true *a 2.115,3.938 2.333,4.146 0.219,0.208 10 true *a

Align the timing mark of the crankshaft pulley and timing chain cover sub-assembly by rotating the crankshaft clockwise.

Text in Illustration
*a Timing Mark


c.

Make sure that the timing mark of the camshaft timing sprocket is at the top.

HINT:

If the timing mark is not at the top, turn the crankshaft pulley 1 revolution so that the timing mark is at the top (set the No. 1 piston to TDC/compression).



Hide 11324 35.REMOVE TIMING CHAIN COVER PLATE

Hide 22100 36.REMOVE SUPPLY PUMP ASSEMBLY

NOTICE:
A354097

Do not hold the supply pump assembly by the parts indicated by the arrows in the illustration.


a.
A343530E01
1.769,4.338 1.954,4.493 0.185,0.155 10 *a 0.529,4.04 0.881,4.196 0.352,0.156 10 SST 0.703,3.429 0.703,4.02 false 2.085,3.637 2.438,3.794 0.352,0.156 10 SST 1.442,3.717 2.032,3.717 false

Using SST, hold the crankshaft pulley and loosen the supply pump shaft nut.

SST
09213-58014  (91551-80840)
09330-00021  

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Do not excessively loosen the supply pump shaft nut, otherwise SST cannot be installed.


HINT:

Rotate the supply pump shaft nut once to loosen it.



b.
A344938E01
1.219,1.552 1.417,1.552 1.417,1.552 1.771,1.313 true 0.865,1.458 1.323,1.656 0.458,0.198 10 true SST

Install SST to the timing chain cover sub-assembly with the 3 bolts.

SST
09241-11010  

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)

HINT:
·

Make sure that the installation direction of SST is as shown in the illustration.

·
A347063E01
0.344,0.137 0.529,0.292 0.185,0.155 10 *a 0.344,2.483 0.529,2.638 0.185,0.155 10 *b 2.369,2.406 2.554,2.560 0.185,0.155 10 *c 1.876,3.126 2.142,2.508 2.142,2.508 2.329,2.508 false

Align the hexagonal portion of SST with the supply pump shaft nut to install SST.



Text in Illustration
*a Engine Front Side
*b Engine Rear Side
*c Hexagonal Portion


c.
A347305

Remove the 2 bolts and No. 1 fuel pump bracket from the cylinder block sub-assembly and supply pump assembly.


d.
A354060

Loosen the 3 nuts to the ends of the stud bolts.

NOTICE:

Do not completely remove the nuts. Otherwise, the supply pump assembly may fall off.



e.
A343532E01
2.987,1.721 3.341,1.882 0.354,0.161 10 SST 2.215,1.558 2.769,1.804 2.769,1.804 2.937,1.804 false

Using SST, loosen the supply pump shaft nut and detach the supply pump assembly and injection pump drive gear.


f.

Remove the 3 nuts from the stud bolts.


g.

Remove the O-ring from the supply pump assembly.


h.

Remove SST from the timing chain cover sub-assembly.


i.
A343534

Remove the supply pump shaft nut from the timing chain cover sub-assembly service hole.


j.

Remove the crankshaft pulley set bolt and crankshaft pulley from the crankshaft.


Hide 22815A 37.REMOVE INJECTION PUMP INSULATOR

a.
A343533

Remove the injection pump insulator from the cylinder block sub-assembly.


Hide 11302 38.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

Hide 11303A 39.REMOVE FRONT CRANKSHAFT OIL SEAL

Hide 15133B 40.REMOVE OIL PUMP RELIEF VALVE PLUG

a.
A343535

Remove the oil pump relief valve plug and gasket from the timing chain cover sub-assembly.


Hide 41.INSPECT BACKLASH OF OIL PUMP GEAR TO OIL PUMP DRIVE GEAR

Hide 13560A 43.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 3 chain tensioner assembly, the plunger and 2 springs may come off of the No. 3 chain tensioner assembly body, but this is not a malfunction.

·
A347346E01
0.554,1.812 0.739,1.967 0.185,0.155 10 *a 1.372,1.682 1.557,1.837 0.185,0.155 10 *b 2.942,1.784 3.127,1.939 0.185,0.155 10 *c 0.667,1.277 0.667,1.814 false 1.457,1.127 1.457,1.664 false 2.368,1.397 2.552,1.551 0.185,0.155 10 *b 2.453,0.842 2.453,1.379 false 3.051,1.323 3.051,1.78 false

Before installing the plunger and 2 springs to the No. 3 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 3 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.
A347347E01
1.844,0.313 1.99,0.313 1.99,0.313 2.198,0.906 false 1.896,1.375 2.063,1.375 2.063,1.375 2.198,0.948 false 0.302,2.813 0.448,2.813 0.448,2.813 0.573,3.208 false 1.802,3.281 1.635,3.281 1.635,3.281 1.396,2.771 true 1.698,1.271 1.885,1.427 0.188,0.156 10 false *a 1.823,3.188 2.01,3.344 0.188,0.156 10 false *b 1.635,0.198 1.823,0.354 0.188,0.156 10 false *c 0.094,2.708 0.281,2.865 0.188,0.156 10 false *a

Fully insert the plunger, align the No. 3 chain tensioner assembly body hole with the plunger groove and insert the pin as shown in the illustration.

Text in Illustration
*a Pin
*b Plunger
*c Plunger Groove


b.
A347348

Remove the 2 bolts, No. 3 chain tensioner assembly and gasket from the engine balancer assembly.


Hide 11991A 44.REMOVE NO. 1 BALANCE SHAFT THRUST PLATE

a.
A347349

Remove the bolt and No. 1 balance shaft thrust plate from the balance shaft gear sub-assembly.


Hide 13639 45.REMOVE BALANCE SHAFT TIMING SPROCKET, BALANCE SHAFT GEAR SUB-ASSEMBLY WITH NO. 3 CHAIN SUB-ASSEMBLY

a.
A347350

Remove the balance shaft timing sprocket, balance shaft gear sub-assembly with No. 3 chain sub-assembly from the crankshaft and engine balancer assembly.


Hide 13620B 46.REMOVE ENGINE BALANCER ASSEMBLY

a.
A347351

Remove the 8 bolts and engine balancer assembly from the cylinder block sub-assembly.


Hide 13550 48.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

a.
A343536E01
1.833,0.323 2.031,0.323 2.031,0.323 2.031,0.927 true 1.813,2.042 2.01,2.042 2.01,2.042 2.01,1.563 true 1.635,0.219 1.865,0.417 0.229,0.198 10 true *b 1.615,1.938 1.833,2.104 0.219,0.167 10 true *a

Allow the plunger to extend slightly, and then rotate the stopper plate clockwise to release the lock. Once the lock is released, push the plunger into the No. 2 chain tensioner assembly.

Text in Illustration
*a Stopper Plate
*b Plunger


b.
A343537E01
1.396,2 2.031,2 true 1.177,1.896 1.365,2.052 0.188,0.156 10 true *a

Allow the plunger to extend slightly, and then rotate the stopper plate clockwise to release the lock. Once the lock is released, push the plunger into the No. 2 chain tensioner assembly.

Text in Illustration
*a Pin


c.
A343538

Remove the 2 bolts and No. 2 chain tensioner assembly from the timing chain case assembly.


Hide 49.REMOVE NO. 2 CHAIN TENSIONER SLIPPER

a.
A343539

Remove the bolt and No. 2 chain tensioner slipper from the timing chain case assembly.


Hide 13562 50.REMOVE NO. 2 CHAIN VIBRATION DAMPER

a.
A343540

Remove the 2 bolts and No. 2 chain vibration damper from the timing chain case assembly.


Hide 13507 51.REMOVE NO. 2 CHAIN SUB-ASSEMBLY

a.

Remove the No. 2 chain sub-assembly from the camshaft timing sprockets and injection pump drive gear.


Hide 13540 52.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

NOTICE:
·

When the pin is removed from the No. 1 chain tensioner assembly, the plunger and spring may come off of the No. 1 chain tensioner assembly body, but this is not a malfunction.

·
A347238E01
1.704,0.281 1.889,0.436 0.185,0.155 10 *a 2.317,0.935 2.502,1.090 0.185,0.155 10 *b 1.593,1.582 1.778,1.737 0.185,0.155 10 *c 1.079,0.379 1.672,0.379 false 1.694,1.035 2.287,1.035 false 1.802,1.69 2.36,1.69 false

Before installing the plunger and spring to the No. 1 chain tensioner assembly body, check that they are free of foreign matter and not damaged.



Text in Illustration
*a No. 1 Chain Tensioner Assembly Body
*b Spring
*c Plunger

a.
A343541E01
0.479,2.708 1.146,2.708 true 1.927,2.802 1.927,2.188 true 2.542,0.969 2.76,0.333 2.76,0.333 2.927,0.333 false 2.542,1.021 2.542,1.375 2.542,1.375 2.74,1.375 false 2.771,1.271 2.958,1.427 0.188,0.156 10 false *a 1.833,2.823 2.052,3 0.219,0.177 10 true *b 2.948,0.24 3.135,0.396 0.188,0.156 10 false *c 0.26,2.604 0.521,2.813 0.26,0.208 10 true *a

Fully insert the plunger, align the No. 1 chain tensioner assembly body hole with the plunger groove and insert the pin as shown in the illustration.

Text in Illustration
*a Pin
*b Plunger
*c Plunger Groove


b.

Remove the 2 bolts, No. 1 chain tensioner assembly and gasket from the cylinder block sub-assembly.


Hide 13559 53.REMOVE NO. 1 CHAIN TENSIONER SLIPPER

a.
A343543

Remove the No. 1 chain tensioner slipper from the straight pin.


Hide 13561 54.REMOVE NO. 1 CHAIN VIBRATION DAMPER

a.
A343544

Remove the bolt and No. 1 chain vibration damper from the cylinder block sub-assembly.


Hide 13506 55.REMOVE CRANKSHAFT TIMING SPROCKET, INJECTION PUMP DRIVE GEAR WITH NO. 1 CHAIN SUB-ASSEMBLY

a.
A343545

Remove the crankshaft timing sprocket, injection pump drive gear with No. 1 chain sub-assembly from the crankshaft and supply pump shaft.


Hide 13523 56.REMOVE CAMSHAFT TIMING SPROCKET

a.

for Exhaust Side:

i.
A343546E01
2.829,0.016 3.014,0.171 0.185,0.155 10 *a

Hold the hexagonal portion of the No. 2 camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the No. 2 camshaft.

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful not to damage the No. 2 camshaft or cylinder head sub-assembly with the wrench.




b.

for Intake Side:

i.
A343547E01
2.496,0.031 2.681,0.186 0.185,0.155 10 *a

Hold the hexagonal portion of the camshaft with a wrench and remove the camshaft timing sprocket bolt and camshaft timing sprocket from the camshaft.

Text in Illustration
*a Hold
V100135

Turn

NOTICE:

Be careful not to damage the camshaft or cylinder head sub-assembly with the wrench.




Hide 11310 57.REMOVE TIMING CHAIN CASE ASSEMBLY

Hide 58.REMOVE NO. 3 CAMSHAFT BEARING CAP

a.
A343548

Remove the 2 camshaft bearing cap bolts and No. 3 camshaft bearing cap from the cylinder head sub-assembly.


Hide 59.REMOVE NO. 1 AND NO. 2 CAMSHAFT BEARING CAP

a.
A347240E01
0.427,1.875 0.563,2.031 0.135,0.156 10 false 2 0.417,0.063 0.552,0.219 0.135,0.156 10 false 1 0.01,0.823 0.146,0.979 0.135,0.156 10 false 3 0.01,1.094 0.146,1.25 0.135,0.156 10 false 4 2.781,0.177 2.917,0.333 0.135,0.156 10 false 5 2.781,1.76 2.917,1.917 0.135,0.156 10 false 7 0.875,0.188 1.01,0.344 0.135,0.156 10 false 9 0.823,1.771 1.042,1.927 0.219,0.156 10 false 11 2.083,0.188 2.302,0.344 0.219,0.156 10 false 13 2.094,1.771 2.313,1.927 0.219,0.156 10 false 15 1.448,0.188 1.667,0.344 0.219,0.156 10 false 17 1.458,1.771 1.677,1.927 0.219,0.156 10 false 19 0.604,1.177 0.823,1.333 0.219,0.156 10 true 10 1.031,0.792 1.25,0.948 0.219,0.156 10 true 12 1.25,1.167 1.469,1.323 0.219,0.156 10 true 18 1.646,0.792 1.865,0.948 0.219,0.156 10 true 20 1.885,1.167 2.104,1.323 0.219,0.156 10 true 14 2.292,0.802 2.51,0.958 0.219,0.156 10 true 16 2.563,1.156 2.698,1.313 0.135,0.156 10 true 6 2.969,0.802 3.104,0.958 0.135,0.156 10 true 8

Remove the 20 camshaft bearing cap bolts in the sequence shown in the illustration.


b.

Remove the No. 1 camshaft bearing cap and 8 No. 2 camshaft bearing caps from the cylinder head sub-assembly.

HINT:

Arrange the removed parts in the correct order.



Hide 13511 60.REMOVE CAMSHAFT

a.

Remove the camshaft from the cylinder head sub-assembly.


Hide 13512 61.REMOVE NO. 2 CAMSHAFT

a.

Remove the No. 2 camshaft from the cylinder head sub-assembly.


Hide 13801 62.REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

a.

Remove the 16 No. 1 valve rocker arm sub-assemblies from the 16 valve lash adjuster assemblies.


Hide 13750 63.REMOVE VALVE LASH ADJUSTER ASSEMBLY

a.

Remove the 16 valve lash adjuster assemblies from the cylinder head sub-assembly.


Hide 13577D 66.REMOVE LOCK PLATE

a.
A343549

Remove the bolt and lock plate from the cylinder block sub-assembly.


Hide 67.REMOVE STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


Hide 68.REMOVE STRAIGHT PIN

NOTICE:

It is not necessary to remove the straight pin unless it is being replaced.