When the ignition switch is ON, the rear power window regulator motor assembly LH is operated by the rear power window regulator switch assembly (for Rear LH Door). The rear power window regulator motor assembly LH has motor, regulator and ECU functions.
The power window control system uses the LIN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power window control system after confirming that the communication system is functioning properly (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING).
If the rear power window regulator motor assembly LH has been replaced with a new one, initialize the power window control system (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION).
Check that the window lock switch is off before performing the following procedure.
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to the Service Bulletin.
As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*
*: w/ Door Control Battery
Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Communication RL-Door Motor | Connection status between rear power window regulator motor assembly LH and main body ECU (multiplex network body ECU) / STOP or OK | STOP: Communication stopped
OK: Normal communication |
- |
On the GTS screen, OK is displayed.
OK
NG
(See pagePower Source / Network>NETWORKING>LIN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING)
Read the Data List according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| RL Door P/W Up SW | Rear LH door power window manual up switch signal / OFF or ON | OFF: Rear LH door power window manual up switch not being operated
ON: Rear LH door power window manual up switch being operated |
- |
| RL Door P/W Down SW | Rear LH door power window manual down switch signal / OFF or ON | OFF: Rear LH door power window manual down switch not being operated
ON: Rear LH door power window manual down switch being operated |
- |
On the GTS screen, ON or OFF is displayed accordingly.
OK
NG
Perform the Active Test according to the display on the GTS (See page Vehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>DATA LIST / ACTIVE TEST).
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
| Tester Display | Test Part | Control Range | Diagnostic Note |
|---|---|---|---|
| Power Window | Power window | OFF/UP/DOWN | - |
Up and down movement does not occur if the arrow is not pressed and held.
Rear LH power window operates normally.
OK
NG
Remove the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>REMOVAL).
Inspect the rear power window regulator switch assembly LH (See page Vehicle Exterior>WINDOW / GLASS>REAR POWER WINDOW SWITCH>INSPECTION).
OK
NG
Disconnect the M2 rear power window regulator switch connector.
Disconnect the M4 power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| M2-6 (UP) - M4-10 (UP) | Always | Below 1 Ω |
| M2-7 (DOWN) - M4-7 (DOWN) | Always | Below 1 Ω |
| M2-6 (UP) - Body ground | Always | 10 kΩ or higher |
| M2-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
OK
NG