Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) › from 2017.08
RM27T0E _58 Vehicle Interior _053730 DOOR LOCK _0261039 WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) J

DOOR LOCK  WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System)  Only Wireless Control Function is Inoperative  


DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

for 12 Pin Type


B487659E02
5.313,3.125 6.958,3.49 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.021,3.115 5.219,3.479 1.198,0.365 10 false Driver Side Junction Block Assembly 2.479,2.146 4.125,2.51 1.646,0.365 10 false Door Control Receiver 0.542,3.156 2.719,3.448 2.177,0.292 10 false Unlock Warning Switch Assembly 5.333,0.802 6.531,1.167 1.198,0.365 10 false PRG 5.323,1.354 6.521,1.719 1.198,0.365 10 false RDA 5.313,2.635 6.51,3 1.198,0.365 10 false KSW 6.208,2.344 6.552,2.604 0.344,0.26 10 false +B 3.594,0.708 4.792,1.073 1.198,0.365 10 false PRG 3.583,1.26 4.781,1.625 1.198,0.365 10 false RDA 2.438,1.25 3.635,1.615 1.198,0.365 10 false GND 2.427,0.531 3.625,0.896 1.198,0.365 10 false +B 1.688,0.698 2.885,1.063 1.198,0.365 10 false ECU-B 0.26,0.521 1.458,0.885 1.198,0.365 10 false from Battery 3.146,0.25 4.344,0.615 1.198,0.365 10 false +B 0.479,3.01 1.677,3.375 1.198,0.365 10 false G3 0.604,2.667 1.802,3.031 1.198,0.365 10 false 2 2.063,2.667 3.26,3.031 1.198,0.365 10 false 1 5.01,2.76 6.208,3.125 1.198,0.365 10 false A 5.021,2.563 6.219,2.927 1.198,0.365 10 false 3 3.896,2.76 5.094,3.125 1.198,0.365 10 false 2N 3.896,2.563 5.094,2.927 1.198,0.365 10 false 28 2.458,1.99 4.104,2.354 1.646,0.365 10 false R41 3.969,0.698 5.167,1.063 1.198,0.365 10 false 5 3.958,1.26 5.156,1.625 1.198,0.365 10 false 4 2.208,1.26 3.406,1.625 1.198,0.365 10 false 12 2.26,0.427 3.458,0.792 1.198,0.365 10 false 7 4.896,1.354 6.094,1.719 1.198,0.365 10 false G218 4.917,0.792 6.115,1.156 1.198,0.365 10 false G218 5.021,1.167 6.219,1.531 1.198,0.365 10 false 4 5.021,0.615 6.219,0.979 1.198,0.365 10 false 5 1.719,2.667 2.917,3.031 1.198,0.365 10 false UN+ 0.792,2.656 1.99,3.021 1.198,0.365 10 false UN-


except 12 Pin Type, for 5L-E


B488365E01
5.063,3.115 6.677,3.458 1.615,0.344 10 false Main Body ECU (Multiplex Network Body ECU) 0.74,3.156 3.635,3.375 2.896,0.219 10 false Unlock Warning Switch Assembly 2.417,2.146 5.313,2.365 2.896,0.219 10 false Door Control Receiver 2.365,2 2.698,2.219 0.333,0.219 10 false R26 3.594,0.708 3.927,0.927 0.333,0.219 10 false PRG 5.365,0.802 5.698,1.021 0.333,0.219 10 false PRG 5.323,1.354 5.656,1.573 0.333,0.219 10 false RDA 3.615,1.26 3.948,1.479 0.333,0.219 10 false RDA 2.417,1.26 2.75,1.479 0.333,0.219 10 false GND 2.25,1.26 2.583,1.479 0.333,0.219 10 false 1 2.427,0.552 2.76,0.771 0.333,0.219 10 false +B 3.135,0.271 3.469,0.49 0.333,0.219 10 false +B 1.688,0.677 2.208,0.917 0.521,0.24 10 false ECU-B 0.281,0.521 1.26,0.927 0.979,0.406 10 false from Battery 5.104,0.646 5.438,0.865 0.333,0.219 10 false 5 5.104,1.24 5.438,1.458 0.333,0.219 10 false 4 4.906,2.958 5.24,3.177 0.333,0.219 10 false G64 5.313,2.656 5.76,2.875 0.448,0.219 10 false KSW 5.073,2.646 5.406,2.865 0.333,0.219 10 false 17 6.208,2.333 6.542,2.552 0.333,0.219 10 false +B 3.979,0.698 4.313,0.917 0.333,0.219 10 false 3 3.969,1.271 4.302,1.49 0.333,0.219 10 false 2 2.26,0.458 2.594,0.677 0.333,0.219 10 false 5 1.729,2.667 2.063,2.885 0.333,0.219 10 false UN+ 0.792,2.677 1.125,2.896 0.333,0.219 10 false UN- 0.74,3 1.073,3.219 0.333,0.219 10 false G3 2.063,2.667 2.396,2.885 0.333,0.219 10 false 1 0.615,2.677 0.948,2.896 0.333,0.219 10 false 2


except 12 Pin Type, except 5L-E


B487659E03
5.313,3.125 6.958,3.49 1.646,0.365 10 false Main Body ECU (Multiplex Network Body ECU) 4.021,3.115 5.219,3.479 1.198,0.365 10 false Driver Side Junction Block Assembly 2.479,2.146 4.125,2.51 1.646,0.365 10 false Door Control Receiver 0.542,3.156 2.719,3.448 2.177,0.292 10 false Unlock Warning Switch Assembly 5.333,0.802 6.531,1.167 1.198,0.365 10 false PRG 5.323,1.354 6.521,1.719 1.198,0.365 10 false RDA 5.313,2.635 6.51,3 1.198,0.365 10 false KSW 6.208,2.344 6.552,2.604 0.344,0.26 10 false +B 3.594,0.708 4.792,1.073 1.198,0.365 10 false PRG 3.583,1.26 4.781,1.625 1.198,0.365 10 false RDA 2.438,1.25 3.635,1.615 1.198,0.365 10 false GND 2.427,0.531 3.625,0.896 1.198,0.365 10 false +B 1.688,0.698 2.885,1.063 1.198,0.365 10 false ECU-B 0.26,0.521 1.458,0.885 1.198,0.365 10 false from Battery 3.146,0.25 4.344,0.615 1.198,0.365 10 false +B 0.479,3.01 1.677,3.375 1.198,0.365 10 false G3 0.604,2.667 1.802,3.031 1.198,0.365 10 false 2 2.063,2.667 3.26,3.031 1.198,0.365 10 false 1 5.01,2.76 6.208,3.125 1.198,0.365 10 false A 5.021,2.563 6.219,2.927 1.198,0.365 10 false 3 3.896,2.76 5.094,3.125 1.198,0.365 10 false 2N 3.896,2.563 5.094,2.927 1.198,0.365 10 false 28 2.458,1.99 4.104,2.354 1.646,0.365 10 false R26 3.969,0.698 5.167,1.063 1.198,0.365 10 false 3 3.958,1.26 5.156,1.625 1.198,0.365 10 false 2 2.271,1.26 3.469,1.625 1.198,0.365 10 false 1 2.26,0.427 3.458,0.792 1.198,0.365 10 false 5 4.896,1.354 6.094,1.719 1.198,0.365 10 false G218 4.917,0.792 6.115,1.156 1.198,0.365 10 false G218 5.021,1.167 6.219,1.531 1.198,0.365 10 false 4 5.021,0.615 6.219,0.979 1.198,0.365 10 false 5 0.781,2.667 1.979,3.031 1.198,0.365 10 false UN- 1.698,2.656 2.896,3.021 1.198,0.365 10 false UN+


CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing or inspecting the door control receiver and wire harness, do not change the position or length of the wire harness. If the wire harness is too close to the door control receiver, wireless function performance may be affected.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

It is necessary to perform initialization after registration of the transmitter IDs into the door control receiver if the door control receiver has been replaced.

for Initialization:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION

for Registration:

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION

·

for 12 Pin Type:

When replacing the door control receiver, read the transmitter IDs (tire pressure warning system) stored in the old ECU using the GTS and write them down before removal.

·

for 12 Pin Type:

First, confirm that there are no malfunctions in the tire pressure warning system. Refer to the How to Proceed with Troubleshooting procedure.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING



PROCEDURE

1.CHECK POWER DOOR LOCK OPERATION
a.

Check the power door lock operation.

Click hereVehicle Interior>DOOR LOCK>POWER DOOR LOCK CONTROL SYSTEM>OPERATION CHECK


Result:
Proceed to
Locked doors unlock
Locked doors do not unlock



Locked doors unlock

2.CHECK KEY REMINDER WARNING SYSTEM

Locked doors do not unlock

2.CHECK KEY REMINDER WARNING SYSTEM
a.

Check that the key reminder warning buzzer operates properly.

Click hereVehicle Interior>DOOR LOCK>KEY REMINDER WARNING SYSTEM>OPERATION CHECK


Result:
Proceed to
Key reminder warning buzzer operates properly
Key reminder warning buzzer does not operates properly



Key reminder warning buzzer operates properly

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

Key reminder warning buzzer does not operates properly

3.CHECK DOOR CONTROL TRANSMITTER ASSEMBLY
a.

When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>OPERATION CHECK


Result:
Result Proceed to
Wireless door lock/unlock/back door open function operates properly with a known good door control transmitter assembly. A
Wireless door lock/unlock/back door open function does not operate. B



A

4.CHECK TRANSMITTER BATTERY (VOLTAGE)

B

5.CHECK WAVE ENVIRONMENT
4.CHECK TRANSMITTER BATTERY (VOLTAGE)


Result:
Proceed to
OK
NG



OK

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

NG

5.CHECK WAVE ENVIRONMENT
a.

Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

HINT:
·

When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

·

If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.




Result:
Proceed to
Wireless functions operate properly
Wireless functions do not operate properly



Wireless functions operate properly

END (AFFECTED BY WAVE INTERFERENCE)

Wireless functions do not operate properly

6.SWITCH TO SELF-DIAGNOSTIC MODE
6.SWITCH TO SELF-DIAGNOSTIC MODE
a.
B220865E36
0.094,0.125 2.021,0.458 1.927,0.333 12 false Interior Light Output: 0.635,1.406 1.063,1.688 0.427,0.281 10 false On 0.573,1.698 1.042,2.01 0.469,0.313 10 false Off 1.552,2.167 1.917,2.5 0.365,0.333 10 false T1 2.146,2.167 2.604,2.604 0.458,0.438 10 false T2 1.979,2.604 3.427,3.042 1.448,0.438 10 false T1: 0.25 seconds 1.979,2.917 3.292,3.313 1.313,0.396 10 false T2: 0.5 seconds 1.802,2.167 2.125,2.51 0.323,0.344 10 false T1

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.


e.

Proceed to the next step in accordance with the prompts on the GTS screen.


f.

Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.


Result:
Proceed to
NEXT



NEXT

7.CHECK SELF DIAGNOSTIC MODE
7.CHECK SELF DIAGNOSTIC MODE
a.

Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

B357193E50
0.135,0.104 2.948,0.583 2.813,0.479 12 false Interior Light Output: 0.26,1.021 3.948,1.271 3.688,0.25 10 false Normal Wave (A) (Lock/Unlock/Glass Hatch Open* Switch): 0.458,2.177 0.917,2.375 0.458,0.198 10 false Off 0.448,1.802 0.906,2 0.458,0.198 10 false On 1.208,2.604 1.667,2.802 0.458,0.198 10 false T1 1.719,2.615 2.177,2.813 0.458,0.198 10 false T2 0.677,3.198 3.823,3.438 3.146,0.24 10 false T1: 0.25 seconds 0.677,3.583 3.823,3.823 3.146,0.24 10 false T2: 0.5 seconds 4.031,0.448 6.323,0.646 2.292,0.198 10 false Unmatching Recognition Code (B): 4.26,0.99 4.719,1.188 0.458,0.198 10 false On 4.281,1.365 4.74,1.563 0.458,0.198 10 false Off 4.917,1.844 6.51,2.094 1.594,0.25 10 false Wave is being received 4.094,2.708 5.688,2.958 1.594,0.25 10 false No Diagnostic Output (C): 4.25,3.188 4.708,3.385 0.458,0.198 10 false Off 0.396,4.354 2.594,4.583 2.198,0.229 10 false *: w/ Glass Hatch Opener System


Result:
Result Proceed to
Normal wave (light flash pattern) is output (A). A
Unmatching recognition code is output (B). B
No diagnostic outputs (C). C



A

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

B

8.CHECK REGISTER RECOGNITION CODE

C

9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
8.CHECK REGISTER RECOGNITION CODE
a.

Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

Click hereVehicle Interior>DOOR LOCK>WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)>REGISTRATION


Result:
Proceed to
Recognition code can be registered
Recognition code cannot be registered



Recognition code can be registered

END (GO TO OPERATION CHECK)

Recognition code cannot be registered

13.REPLACE DOOR CONTROL RECEIVER
9.CHECK DOOR CONTROL RECEIVER (RESPONSE)
a.

Prepare the door control transmitter assembly from another vehicle.


b.

Press and hold down the door control transmitter assembly switch.


c.

Check that an unmatching recognition code is output.


Result:
Proceed to
Unmatching recognition code is output
Unmatching recognition code is not output



Unmatching recognition code is output

REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

Unmatching recognition code is not output

10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
10.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)
a.
E198671C43
1.385,0.385 1.802,0.656 0.417,0.271 1.229,1.594 0.865,1.906 0.865,1.906 0.75,1.906 true 2.042,1.615 2.375,1.927 2.375,1.927 2.552,1.927 true 0.073,0.083 0.385,0.281 0.313,0.198 10 false *a 1.469,0.427 1.927,0.625 0.458,0.198 10 false R41 0.542,1.833 0.854,2.031 0.313,0.198 10 false +B 2.625,1.844 3.292,2.042 0.667,0.198 10 false GND
*a Front view of wire harness connector
(to Door Control Receiver)


for 12 Pin Type:

i.

Disconnect the door control receiver connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-12 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R41-7 (+B) - Body ground Always 11 to 14 V




b.
B281165C31
1.49,0.146 1.906,0.375 0.417,0.229 2.594,1.406 2.208,1.406 false 1.219,1.406 0.833,1.406 false 0.125,0.094 0.302,0.24 0.177,0.146 10 false *a 0.469,1.333 1.073,1.573 0.604,0.24 10 false GND 2.667,1.323 3.146,1.563 0.479,0.24 10 false +B 1.594,0.177 2.427,0.51 0.833,0.333 10 false R26
*a Front view of wire harness connector
(to Door Control Receiver)


except 12 Pin Type:

i.

Disconnect the door control receiver connector.


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R26-1 (GND) - Body ground Always Below 1 Ω



iii.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R26-5 (+B) - Body ground Always 11 to 14 V




Result:
Proceed to
OK
NG



OK

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK DOOR CONTROL RECEIVER (OUTPUT)
a.

for 12 Pin Type:

i.
B488351C02
1.563,0.25 1.885,0.479 0.323,0.229 0.938,0.573 1.042,0.573 1.042,0.573 1.646,1.01 true 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.573,0.5 0.885,0.698 0.313,0.198 10 false RDA 1.604,0.292 1.917,0.49 0.313,0.198 10 false R41
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R41-4 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




b.

except 12 Pin Type:

i.
B281169C17
1.49,0.375 1.927,0.604 0.438,0.229 1.875,1.281 2.26,1.875 2.26,1.875 2.365,1.875 false 0.24,0.167 0.583,0.49 0.344,0.323 10 false *a 2.417,1.792 2.906,1.979 0.49,0.188 10 false RDA 1.594,0.417 1.969,0.594 0.375,0.177 10 false R26
*a Component with harness connected
(Door Control Receiver)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R26-2 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V
Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation
(0 to 12 V)




Result:
Result Proceed to
OK (for 12 Pin Type) A
OK (except 12 Pin Type) B
NG C



A

12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

B

16.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))

C

12.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the R41 door control receiver connector.


b.

Disconnect the G218 main body ECU (multiplex network body ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-4 (RDA) - G218-16 (RDA) Always Below 1 Ω
R41-5 (PRG) - G218-4 (PRG) Always Below 1 Ω
R41-4 (RDA) or G218-16 (RDA) - Other terminals and body ground Always 10 kΩ or higher
R41-5 (PRG) or G218-4 (PRG) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (for 5 Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

14.CHECK REGISTER RECOGNITION CODE
14.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

15.CHECK DOOR CONTROL RECEIVER (OPERATION)
15.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

16.CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU))
a.

Disconnect the R26 door control receiver connector.


b.

Disconnect the G64*1 or G218*2 main body ECU (multiplex network body ECU) connector.

*1: for 5L-E

*2: except 5L-E



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for 5L-E:
Tester Connection Condition Specified Condition
R26-2 (RDA) - G64-26 (RDA) Always Below 1 Ω
R26-3 (PRG) - G64-25 (PRG) Always Below 1 Ω
R26-2 (RDA) or G64-26 (RDA) - Other terminals and body ground Always 10 kΩ or higher
R26-3 (PRG) or G64-25 (PRG) - Other terminals and body ground Always 10 kΩ or higher

except 5L-E:
Tester Connection Condition Specified Condition
R26-2 (RDA) - G218-4 (RDA) Always Below 1 Ω
R26-3 (PRG) - G218-5 (PRG) Always Below 1 Ω
R26-2 (RDA) or G218-4 (RDA) - Other terminals and body ground Always 10 kΩ or higher
R26-3 (PRG) or G218-5 (PRG) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.REPLACE DOOR CONTROL RECEIVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.REPLACE DOOR CONTROL RECEIVER
a.

Temporarily replace the door control receiver with a new or known good one.

Click hereVehicle Interior>DOOR LOCK>DOOR CONTROL RECEIVER (for 5 Door)>REMOVAL


Result:
Proceed to
NEXT



NEXT

18.CHECK REGISTER RECOGNITION CODE
18.CHECK REGISTER RECOGNITION CODE

Result:
Proceed to
NEXT



NEXT

19.CHECK DOOR CONTROL RECEIVER (OPERATION)
19.CHECK DOOR CONTROL RECEIVER (OPERATION)
a.

Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

OK:

Doors can be locked and unlocked by the door control transmitter assembly.



Result:
Proceed to
OK
NG



OK

END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

NG

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)