Home › Engine / Hybrid System › 1GR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2017.08
RM27T0E _51 Engine / Hybrid System _053657 1GR-FE ENGINE CONTROL _0260436 SFI SYSTEM C

1GR-FE ENGINE CONTROL  SFI SYSTEM  P2440  Secondary Air Injection System Switching Valve Stuck Open Bank1  P2441  Secondary Air Injection System Switching Valve Stuck Close Bank1  P2442  Secondary Air Injection System Switching Valve Stuck Open Bank 2  P2443  Secondary Air Injection System Switching Valve Stuck Closed Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

DTC No. DTC Detection Condition Trouble Area
P2440 The pressure sensor detects a pulsation in the exhaust gas despite the ECM commanding the emission control valve (ASV) to close while the engine is running (1 trip detection logic).
·

Emission control valve set

·

Open or short in emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver

·

ECM


When secondary air injection is off, the cumulative pressure pulsation exceeds the threshold (1 trip detection logic).
P2441 The pressure sensor detects no pulsation in the exhaust gas despite the ECM commanding the emission control valve (ASV) to open while the engine is running (2 trip detection logic).
·

Emission control valve set

·

Open or short in emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

Air injection control driver

·

ECM

·

Open or short in air pump heater circuit

·

AIR PMPHTR relay

·

Air pump assembly


When secondary air injection is turned on (when only the emission control valve for bank 2 is closed), there is no exhaust gas pulsation (2 trip detection logic).
P2442 The pressure sensor detects a pulsation in the exhaust gas despite the ECM commanding the emission control valve (ASV) to close while the engine is running (1 trip detection logic).
·

No. 2 emission control valve set

·

Open or short in No. 2 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

AIR VSV relay

·

ECM


When secondary air injection is turned on (when only the emission control valve for bank 2 is open), there is no change in the secondary air injection pressure (1 trip detection logic).
When secondary air injection is off, the cumulative pressure pulsation exceeds the threshold (1 trip detection logic).
P2443 The pressure sensor detects no pulsation in the exhaust gas despite the ECM commanding the emission control valve (ASV) to open while the engine is running (2 trip detection logic).
·

No. 2 emission control valve set

·

Open or short in No. 2 emission control valve circuit

·

Air injection system piping

·

Pressure sensor

·

Pressure sensor circuit

·

AIR VSV relay

·

ECM

·

Open or short in air pump heater circuit

·

AIR PMP HTR relay

·

Air pump assembly


When secondary air injection is turned on (when only the emission control valve for bank 2 is open), there is no change in the secondary air injection pressure (2 trip detection logic).

HINT:

Emission control valve normal operation:

When the emission control valve is open, exhaust gas pulsation occurs in the secondary air passage.

When the emission control valve is closed, exhaust gas pulsation does not occur in the secondary air passage.


MONITOR DESCRIPTION

DTCs P2440 and P2442 indicate that the emission control valve is stuck open. DTCs P2441 and P2443 indicate that the emission control valve is stuck closed. The ECM performs diagnosis of the secondary air injection system based on the changes in pressure and the pressure pulsation. If a malfunction is detected, the ECM illuminates the MIL and stores a DTC.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions. Furthermore, pending codes also can be checked by performing Utility / Secondary Air Injection Check / Automatic Mode after the repair.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Read the DTCs and freeze frame data.

Result
Result Proceed to
P2440, P2441, P2442 and/or P2443 is output A
P2440 and/or P2441 and P0412 are output B
P2442 and/or P2443 and P0416 and/or P0417 are output C
P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412, P0416 and P0417) are output D

HINT:

If any DTCs other than P0412, P0416, P0417, P2440, P2441, P2442 and P2443 are output, troubleshoot those DTCs first.




A

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)

B

GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0412)

C

GO TO EMISSION CONTROL VALVE INSPECTION PROCEDURE (P0416 AND P0417)

D

2.CHECK FREEZE FRAME DATA (AIR PUMP FREEZE, AIR SWITCHING VALVE FREEZE AND AIR SWITCHING VALVE2 FREEZE)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Read the values of Air Pump Freeze, Air Switching Valve Freeze and Air Switching Valve2 Freeze from the freeze frame data recorded previously.


d.

Referring to the following table, proceed to the appropriate step according to the result of the data reading.

Result
Result Proceed to
Air Pump Freeze Air Switching Valve Freeze Air Switching Valve2 Freeze
OFF OFF OFF B
Except above A



A

3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)

B

7.INSPECT AIR PUMP ASSEMBLY
3.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE AIR PUMP HEATER)
a.
U169184E01
0.158,0.027 0.339,0.227 0.181,0.200 10 *a 1.608,0.08 1.896,0.243 0.288,0.163 10 A18 1.608,0.887 0.836,1.559 false 0.394,1.543 0.841,1.734 0.448,0.191 10 APH+

Disconnect the air pump connector.


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG) and turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT/ Active Test / Activate the Air Pump Heater.


e.

Measure the voltage according to the value(s) in the table below.

:
Tester Connection Condition Specified Condition
A18-1 (APH+) - Body ground Activate the Air Pump Heater is ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Air Pump Assembly)


f.

Reconnect the air pump connector.



OK

4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)
4.INSPECT AIR PUMP ASSEMBLY (HEATER RESISTANCE)

OK

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)

NG

5.INSPECT NO. 1 INTEGRATION RELAY (AIR PMP HTR RELAY)
a.

Inspect the No. 1 integration relay (AIR PMP HTRrelay) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - NO. 1 INTEGRATION RELAY, BODY GROUND)

NG

REPLACE NO. 1 INTEGRATION RELAY

6.CHECK HARNESS AND CONNECTOR (AIR PUMP - NO. 1 INTEGRATION RELAY, BODY GROUND)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the air pump connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
1T-12 - A18-1 (APH+) Always Below 1 Ω
A18-3 (APHG) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
1T-12 or A18-1 (APH+) - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the air pump connector.



OK

7.INSPECT AIR PUMP ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.INSPECT AIR PUMP ASSEMBLY

OK

8.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)

NG

8.PERFORM ACTIVE TEST USING GTS (SECONDARY AIR INJECTION SYSTEM OPERATION)
A221579E01
0.079,0 0.306,0.163 0.228,0.163 10 *A 0.079,2.019 0.281,2.212 0.202,0.193 10 *B

a.

Perform a visual check:

i.

Start the engine and warm it up.


ii.

Turn the engine switch off.


iii.

Disconnect the air hoses.


iv.

Connect the GTS to the DLC3.


v.

Turn the engine switch on (IG).


vi.

Turn the GTS on.


vii.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



viii.

Start the engine.


ix.

Perform the secondary air injection system forced operation while the engine is idling.


x.

Place your hand near the emission control valve port and check that the exhaust gas pressure pulsates when the emission control valve is turned on.

CAUTION:

To avoid the danger of being burned by the exhaust gas, bring your hand close to the valve port slowly.



xi.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV1: OPEN, ASV2: OPEN and AIR PUMP: ON, ASV1: CLOSE, ASV2: CLOSE.


xii.

Check that the exhaust gas does not pulsate when the emission control valve is turned off.


xiii.

Turn the engine switch off.

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



OK:
Air Pump Operation Emission Control Valve Operation Exhaust Gas Pulsation
ON CLOSE Not detected
ON OPEN Detected


Text in Illustration
*A for Bank 1
*B for Bank 2




OK

9.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)

NG

10.INSPECT AIR TUBE (BLOCKAGE AND LEAKAGE)
9.INSPECT EMISSION CONTROL VALVE SET (PRESSURE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).


e.

Check the pressure displayed on the GTS.

Standard pressure:

45 to 135 kPa


HINT:

The GTS displays the air pump pressure as absolute pressure.


Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

B

C

10.INSPECT AIR TUBE (BLOCKAGE AND LEAKAGE)
A221586

a.

Check that the air tubes are securely connected to both the exhaust manifold and the emission control valve.


b.

Inspect the air tube for blockages and damage.

OK:

No blockages in or damage to air tubes.




OK

11.INSPECT EMISSION CONTROL VALVE SET

NG

REPLACE AIR TUBE

11.INSPECT EMISSION CONTROL VALVE SET

b.

Inspect the No. 2 emission control valve set (See page Engine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR SWITCHING VALVE(for Bank 2)>INSPECTION).

Result
Result Proceed to
OK A
NG (for Bank 1) B
NG (for Bank 2) C



A

12.INSPECT NO. 1 INTEGRATION RELAY (AI-VSV RELAY)

B

C

12.INSPECT NO. 1 INTEGRATION RELAY (AI-VSV RELAY)
a.

Inspect the No. 1 integration relay (AI-VSV) (See page Engine / Hybrid System>1GR-FE (ENGINE CONTROL)>RELAY>ON-VEHICLE INSPECTION).



OK

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)

NG

REPLACE NO. 1 INTEGRATION RELAY

13.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - ECM)
a.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1U-1 - G56-24 (AIR1) Always Below 1 Ω
1U-1 or G56-24 (AIR1) - Body ground Always 10 kΩ or higher



d.

Reinstall the No. 1 integration relay.


e.

Reconnect the ECM connector.



OK

14.CHECK HARNESS AND CONNECTOR (NO. 2 EMISSION CONTROL VALVE SET - NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (NO. 2 EMISSION CONTROL VALVE SET - NO. 1 INTEGRATION RELAY)
a.

Disconnect the No. 2 emission control valve set connector.


b.

Remove the No. 1 integration relay from the engine room relay block and junction block assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C45-5 (+BL) - 1N-2 Always Below 1 Ω
C45-1 (GNDL) - Body ground Always Below 1 Ω
C45-5 (+BL) or 1N-2 - Body ground Always 10 kΩ or higher



d.

Reconnect the No. 2 emission control valve set connector.


e.

Reinstall the No. 1 integration relay.



OK

15.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR (POWER SOURCE OF AIR INJECTION CONTROL DRIVER)
U169185E01
1.554,0.284 1.842,0.447 0.288,0.163 10 A17 1.529,2.264 1.817,2.427 0.288,0.163 10 A16 0.617,1.918 1.162,2.095 0.545,0.177 10 BATT 1.408,1.349 0.875,1.869 false 0.94,3.861 1.068,4.038 0.128,0.177 10 E 2.373,3.861 2.616,4.038 0.242,0.177 10 +B 2.059,3.293 2.414,3.861 false 1.172,3.287 1.015,3.831 false 0.172,0.096 0.376,0.308 0.204,0.211 10 *a

a.

Disconnect the air injection control driver connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A16-1 (E) - Body ground Always Below 1 Ω



c.

Turn the engine switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A17-1 (BATT) - Body ground Always 11 to 14 V
A16-5 (+B) - Body ground Engine switch on (IG) 11 to 14 V



Text in Illustration
*a Front view of wire harness connector
(to Air Injection Control Driver)

e.

Reconnect the air injection control driver connectors.



OK

16.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the ECM connectors.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C36-20 (AIRV) - A16-3 (SIV) Always Below 1 Ω
C36-20 (AIRV) or A16-3 (SIV) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connectors.


e.

Reconnect the air injection control driver connector.



OK

17.PERFORM ACTIVE TEST USING GTS

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.PERFORM ACTIVE TEST USING GTS
a.
U147661E03
1.375,2.604 1.177,3.094 false 1.542,2.615 1.5,3.094 false 1.677,2.615 1.938,3.094 false 1.813,2.615 2.281,3.104 false 0.646,2.479 0.906,2.656 0.26,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.094,3.115 1.281,3.292 0.188,0.177 10 false E 1.448,3.115 1.656,3.292 0.208,0.177 10 false DI 1.875,3.125 2.271,3.302 0.396,0.177 10 false SIV 2.302,3.115 2.708,3.292 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.771 2.885,0.948 0.438,0.177 10 false AIDI 2.448,1.125 2.896,1.302 0.448,0.177 10 false AIRV 0.865,0.771 1.073,0.948 0.208,0.177 10 false DI 0.781,1.125 1.177,1.302 0.396,0.177 10 false SIV

Disconnect the air injection control driver connector.


b.

Connect terminals DI and SIV of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG) and turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



f.

Start the engine.


g.

Perform the secondary air injection system forced operation while the engine is idling.


h.

Measure the voltage between the SIV and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


i.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-3 (SIV) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A16-3 (SIV) - A16-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



j.
U147662E04
1.396,2.625 1.198,3.115 false 1.531,2.615 1.49,3.094 false 1.667,2.615 1.927,3.094 false 1.813,2.615 2.281,3.104 false 0.625,2.479 0.885,2.656 0.26,0.177 10 false A16 0.979,1.844 1.219,2.021 0.24,0.177 10 false *a 1.125,3.125 1.313,3.302 0.188,0.177 10 false E 1.448,3.125 1.656,3.302 0.208,0.177 10 false DI 1.885,3.125 2.281,3.302 0.396,0.177 10 false SIV 2.292,3.115 2.698,3.292 0.406,0.177 10 false SIP 2.531,0.063 2.771,0.24 0.24,0.177 10 false *2 0.667,0.208 0.906,0.385 0.24,0.177 10 false *1 2.448,0.76 2.896,0.938 0.448,0.177 10 false AIDI 2.448,1.135 2.906,1.313 0.458,0.177 10 false AIRP 0.865,0.771 1.073,0.948 0.208,0.177 10 false DI 0.781,1.125 1.177,1.302 0.396,0.177 10 false SIP

Connect terminals DI and SIP of the wire harness connector for the air injection control driver.

Text in Illustration
*1 Air Injection Control Driver
*2 ECM
*a Front view of wire harness connector
(to Air Injection Control Driver)


k.

Connect the GTS to the DLC3.


l.

Turn the engine switch on (IG) and turn the GTS on.


m.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP: ON, ASV 1: OPEN, ASV 2: OPEN.

HINT:

When Manual Mode is selected, the GTS initialization (atmospheric pressure measurement) is performed automatically. The initialization takes 10 seconds. After the initialization, AIR PUMP and ASV operation can be selected.



n.

Start the engine.


o.

Perform the secondary air injection system forced operation while the engine is idling.


p.

Measure the voltage between the SIP and E terminals of the ECM connector when the secondary air injection system is ON and OFF.


q.

Turn the engine switch off.

NOTICE:
·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



Standard Voltage:
Tester Connection Condition Specified Condition
A16-4 (SIP) - A16-1 (E) AIR PUMP: ON, ASV: OPEN 0.5 to 2 V
A16-4 (SIP) - A16-1 (E) AIR PUMP: OFF, ASV: CLOSE 11 to 14 V



r.

Reconnect the air injection control driver connector.



OK

18.REPLACE AIR INJECTION CONTROL DRIVER

NG

18.REPLACE AIR INJECTION CONTROL DRIVER
a.

Replace the air injection control driver (See page Engine / Hybrid System>1GR-FE (EMISSION CONTROL)>AIR INJECTION DRIVER>REMOVAL).



NEXT

19.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
19.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443)
a.

Start the engine and warm it up.


b.

Turn the engine switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the engine switch on (IG).


e.

Turn the GTS on.



g.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.


h.

Start the engine after the GTS initialization is finished.


i.

Perform the System Check operation by pressing ENTER (Next).


j.

Perform the following to confirm the secondary air injection system pending codes: Press the Exit button.


k.

Check for pending DTCs.

OK:

No pending DTC is output.



l.

Turn the engine switch off.

NOTICE:
·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned to on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.





OK

END

NG