Home › Vehicle Exterior › WINDOW / GLASS › HEATED WINDSHIELD DEFROSTER SYSTEM › 2017.08–2020.08
RM27T0E _59 Vehicle Exterior _053742 WINDOW / GLASS _0326777 HEATED WINDSHIELD DEFROSTER SYSTEM J

WINDOW / GLASS  HEATED WINDSHIELD DEFROSTER SYSTEM  Heated Windshield Defroster System does not operate  


DESCRIPTION

When the front window deicer switch is operated, the operation signal is transmitted to the air conditioning amplifier assembly directly. When the air conditioning amplifier assembly receives the signal, it turns on the HWD NO.1 relay, HWD NO.2 relay, HWD NO.3 relay and HWD NO.4 relay to operate the heated windshield defroster system.

WIRING DIAGRAM

E377826E01
1.073,0.344 1.99,0.542 0.917,0.198 10 false ECU-IG NO.2 2.604,0.177 3.875,0.365 1.271,0.188 10 false from IG NO.1 Relay 1.271,1.802 2.969,2.021 1.698,0.219 10 false Front Wiper Deicer Switch 1.927,2.927 2.385,3.125 0.458,0.198 10 false ECM 3.646,3.021 5.208,3.438 1.563,0.417 10 false Air Conditioning Amplifier Assembly 1.156,0.76 1.469,0.958 0.313,0.198 10 false IG 2.802,0.76 2.958,0.958 0.156,0.198 10 false D 2.813,1.177 2.969,1.375 0.156,0.198 10 false E 3.875,0.885 4.49,1.083 0.615,0.198 10 false FDFI 3.875,1.271 4.333,1.469 0.458,0.198 10 false SW1 4.469,1.073 4.917,1.313 0.448,0.24 10 false FDEF 0.573,4.354 1.396,4.583 0.823,0.229 10 false from Battery 2.365,4.531 3.281,4.729 0.917,0.198 10 false DEICER 2.323,4.833 3.26,5.063 0.938,0.229 10 false to EHW Relay 2.292,6.656 3.052,6.865 0.76,0.208 10 false HWD NO.1 3.875,5.146 4.479,5.385 0.604,0.24 10 false DEICER 3.76,7.344 4.542,7.573 0.781,0.229 10 false HWD NO.1 0.563,8.469 2.271,8.708 1.708,0.24 10 false : CAN Communication Line 5.479,7.677 7.104,8.073 1.625,0.396 10 false Windshield Glass (Heated Windshield Defroster) 5.99,4.354 6.146,4.552 0.156,0.198 10 false B 5.99,6.5 6.146,6.698 0.156,0.198 10 false B 6,7.031 6.156,7.229 0.156,0.198 10 false E 5.531,4.365 6.146,4.563 0.615,0.198 10 false A123 5.542,6.5 6.156,6.698 0.615,0.198 10 false A108 5.531,7.042 6.146,7.24 0.615,0.198 10 false A108 3.438,0.875 3.896,1.073 0.458,0.198 10 false G24 3.448,1.281 3.906,1.479 0.458,0.198 10 false G24 4.938,1.052 5.396,1.25 0.458,0.198 10 false G25 1.271,1.615 1.729,1.813 0.458,0.198 10 false G219 0.917,0.75 1.073,0.948 0.156,0.198 10 false 5 3.052,0.76 3.208,0.958 0.156,0.198 10 false 4 3.063,1.167 3.219,1.365 0.156,0.198 10 false 2 3.479,0.677 3.792,0.875 0.313,0.198 10 false 11 3.521,1.083 3.677,1.281 0.156,0.198 10 false 5 5,0.844 5.313,1.042 0.313,0.198 10 false 40 3.698,3.833 3.854,4.031 0.156,0.198 10 false 2 4.469,4.24 4.625,4.438 0.156,0.198 10 false 5 4.5,5.979 4.656,6.177 0.156,0.198 10 false 2 3.708,6.385 3.865,6.583 0.156,0.198 10 false 5 4.5,3.823 4.656,4.021 0.156,0.198 10 false 1 3.698,5.99 3.854,6.188 0.156,0.198 10 false 1 3.698,4.271 3.854,4.469 0.156,0.198 10 false 3 3.698,4.74 3.854,4.938 0.156,0.198 10 false 4 4.469,6.385 4.625,6.583 0.156,0.198 10 false 3 4.479,6.906 4.635,7.104 0.156,0.198 10 false 4 5.667,4.156 5.823,4.354 0.156,0.198 10 false 2 5.667,6.302 5.823,6.5 0.156,0.198 10 false 4 5.656,6.844 5.813,7.042 0.156,0.198 10 false 1

E377827E01
2.302,1.198 3.531,1.396 1.229,0.198 10 false HWD NO.2 3.781,1.802 5.01,2 1.229,0.198 10 false HWD NO.2 2.25,3.083 3.479,3.281 1.229,0.198 10 false HWD NO.3 3.802,3.698 5.031,3.896 1.229,0.198 10 false HWD NO.3 2.219,4.979 3.448,5.177 1.229,0.198 10 false HWD NO.4 3.813,5.615 5.042,5.813 1.229,0.198 10 false HWD NO.4 5.49,6.542 7.115,6.979 1.625,0.438 10 false Windshield Glass (Heated Windshield Defroster) 6,0.958 6.156,1.156 0.156,0.198 10 false B 5.979,6.031 6.135,6.229 0.156,0.198 10 false E 6,2.896 6.156,3.094 0.156,0.198 10 false B 6,4.781 6.156,4.979 0.156,0.198 10 false B 6,5.313 6.156,5.51 0.156,0.198 10 false E 6,3.427 6.156,3.625 0.156,0.198 10 false E 5.99,1.51 6.146,1.708 0.156,0.198 10 false E 5.552,0.969 6.167,1.167 0.615,0.198 10 false A123 5.531,6.042 6.146,6.24 0.615,0.198 10 false A123 5.542,1.521 6.156,1.719 0.615,0.198 10 false A108 5.542,2.896 6.156,3.094 0.615,0.198 10 false A109 5.552,3.427 6.167,3.625 0.615,0.198 10 false A109 5.552,4.792 6.167,4.99 0.615,0.198 10 false A109 5.542,5.333 6.156,5.531 0.615,0.198 10 false A109 5.677,0.76 5.833,0.958 0.156,0.198 10 false 4 5.667,1.313 5.865,1.49 0.198,0.177 10 false 3 5.667,2.677 5.823,2.875 0.156,0.198 10 false 1 5.656,3.208 5.813,3.406 0.156,0.198 10 false 2 5.656,4.594 5.854,4.771 0.198,0.177 10 false 3 5.656,5.125 5.813,5.323 0.156,0.198 10 false 4 5.667,5.854 5.823,6.052 0.156,0.198 10 false 1 3.698,0.479 3.854,0.677 0.156,0.198 10 false 1 3.698,0.854 3.854,1.052 0.156,0.198 10 false 5 4.5,0.469 4.656,0.667 0.156,0.198 10 false 2 4.49,0.844 4.688,1.021 0.198,0.177 10 false 3 4.49,1.385 4.646,1.583 0.156,0.198 10 false 4 3.698,2.365 3.854,2.563 0.156,0.198 10 false 1 3.708,4.302 3.865,4.5 0.156,0.198 10 false 1 4.5,2.375 4.656,2.573 0.156,0.198 10 false 2 3.698,2.75 3.854,2.948 0.156,0.198 10 false 5 3.688,4.667 3.844,4.865 0.156,0.198 10 false 5 4.51,4.292 4.667,4.49 0.156,0.198 10 false 2 4.49,2.771 4.688,2.948 0.198,0.177 10 false 3 4.49,4.667 4.688,4.844 0.198,0.177 10 false 3 4.479,5.219 4.635,5.417 0.156,0.198 10 false 4 4.5,3.313 4.656,3.51 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

The heated windshield defroster system uses the CAN communication system. First, confirm that there are no malfunctions in the communication system by checking the communication function of the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure

Click hereVehicle Exterior>WINDOW / GLASS>HEATED WINDSHIELD DEFROSTER SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the ambient temperature is 5°C (41°F) or higher, or if a malfunction of the ambient temperature sensor (thermistor assembly) is detected, the HWD NO. 3 relay will be deactivated and the front window deicer switch indicator light will blink.

·

As the door control battery is installed between the vehicle battery and main body ECU (multiplex network body ECU), first perform the inspections in On-Vehicle Inspection to confirm that there are no malfunctions in the power source circuit for the main body ECU (multiplex network body ECU) before performing this troubleshooting procedure.*

*: w/ Door Control Battery



PROCEDURE

1.CHECK HEATED WINDSHIELD DEFROSTER SYSTEM
a.

Check if the heated windshield defroster is operating.

Click hereVehicle Exterior>WINDOW / GLASS>HEATED WINDSHIELD DEFROSTER SYSTEM>OPERATION CHECK


Result:
Result Proceed to
None of the heated windshield defroster operate. A
Some of the heated windshield defroster do not operate B



A

2.INSPECT FRONT WIPER DEICER SWITCH

B

8.INSPECT HWD NO.1 RELAY, HWD NO.2 RELAY, HWD NO.3 RELAY, HWD NO.4 RELAY
2.INSPECT FRONT WIPER DEICER SWITCH

OK

3.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY AND BATTERY)

NG

3.CHECK WIRE HARNESS AND CONNECTOR (FRONT WIPER DEICER SWITCH - AIR CONDITIONING AMPLIFIER ASSEMBLY AND BATTERY)
a.
E380278C01
1.49,0.219 1.958,0.438 0.469,0.219 2.427,1.927 2.219,1.927 2.219,1.927 1.938,1.438 true 0.958,1.927 1.167,1.927 1.167,1.927 1.479,1.427 true 1.781,1.906 1.781,1.427 true 0.073,0.031 0.385,0.188 0.313,0.156 10 false *a 1.552,0.24 1.969,0.448 0.417,0.208 10 false G219 2.51,1.844 2.823,2.042 0.313,0.198 10 false IG 0.781,1.833 1.094,2.031 0.313,0.198 10 false E 1.75,1.938 2.063,2.135 0.313,0.198 10 false D
*a Front view of wire harness connector
(to Front Wiper Deicer Switch)


Disconnect the front wiper switch connector.


b.

Disconnect the G24 air conditioning amplifier assembly connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G219-5 (IG) - Body ground Engine switch off Below 1 V
Engine switch on (IG) 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G219-2 (E) - G24-5 (SW1) Always Below 1 Ω
G219-4 (D) - G24-11 (FDFI) Always Below 1 Ω
G219-2 (E) or G24-5 (SW 1) - Body ground Always 10 kΩ or higher
G219-4 (D) or G24-11 (FDFI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT DEICER RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT DEICER RELAY
a.

Remove the DEICER relay from the No. 5 relay block.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (DEICER RELAY - BATTERY)

NG

REPLACE DEICER RELAY

5.CHECK HARNESS AND CONNECTOR (DEICER RELAY - BATTERY)
a.
B495605C01
0.083,0.094 0.396,0.25 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to DEICER Relay)


Remove the DEICER relay from the No. 5 relay block.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
DEICER relay terminal 3 - Body ground Always 11 to 14 V
DEICER relay terminal 2 - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIRCONDITIONING AMPLIFIER ASSEMBLY, HWD NO.1 RELAY, WINDSHIELD GLASS AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (DEICER RELAY - AIRCONDITIONING AMPLIFIER ASSEMBLY, HWD NO.1 RELAY, WINDSHIELD GLASS AND BODY GROUND)
a.

Disconnect the A123 windshield glass (heated windshield defroster) connector.


b.

Disconnect the G25 air conditioning amplifier assembly connector.


c.

Remove the DEICER relay from the No. 5 relay block.


d.

Remove the HWD NO.1 relay and HWD NO.2 relay from the No. 5 relay block.


e.

Remove the HWD NO.3 relay and HWD NO.4 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
DEICER relay terminal 5 - A123-2 (B) Always Below 1 Ω
A123-1 (E) - Body ground Always Below 1 Ω
DEICER relay terminal 1 - G25-40 (FDEF) Always Below 1 Ω
DEICER relay terminal 5 - HWD NO.1 relay terminal 2 Always Below 1 Ω
DEICER relay terminal 5 or A123-2 (B) - Body ground Always 10 kΩ or higher
DEICER relay terminal 1 or G25-40 (FDEF) - Body ground Always 10 kΩ or higher
DEICER relay terminal 5 or HWD NO.1 relay terminal 2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.PERFORM ACTIVE TEST USING GTS (HWD RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.PERFORM ACTIVE TEST USING GTS (HWD RELAY)
a.

Using the GTS, perform the Active Test.

Click hereVehicle Exterior>WINDOW / GLASS>WINDSHIELD DEICER SYSTEM>DATA LIST / ACTIVE TEST

Air Conditioner
Tester Display Measurement Item Control Range Diagnostic Note
HWD Relay Windshield glass (windshield deicer wire) OFF or ON -

OK:

The heated windshield defroster system operates normally.



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER)

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

8.INSPECT HWD NO.1 RELAY, HWD NO.2 RELAY, HWD NO.3 RELAY, HWD NO.4 RELAY
a.

HWD NO.1 relay:

i.

Remove the HWD NO.1 relay from the No. 5 relay block.




b.

HWD NO.2 relay:

i.

Remove the HWD NO.2 relay from the No. 5 relay block.




c.

HWD NO.3 relay:

i.

Remove the HWD NO.3 relay from the No. 1 engine room relay block and No. 1 junction block assembly.




d.

HWD NO.4 relay:

i.

Remove the HWD NO.4 relay from the No. 1 engine room relay block and No. 1 junction block assembly.




Result:
Proceed to
OK
NG



OK

9.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.1 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER]) BATTERY AND BODY GROUND)

NG

REPLACE HWD NO.1 RELAY, HWD NO.2 RELAY, HWD NO.3 RELAY, HWD NO.4 RELAY

9.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.1 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER]) BATTERY AND BODY GROUND)
a.
E380053C01
0.719,2.385 1.031,2.542 0.313,0.156 10 false *a
*a HWD NO.1 Relay Holder


Disconnect A108 windshield glass (heated windshield defroster) connector.


b.

Remove the HWD NO.1 relay from the No. 5 relay block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO.1 relay holder terminal 5 - Body ground Always 11 to 14 V
HWD NO.1 relay holder terminal 2 - Body ground Front wiperdeicer switch on 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO.1 relay holder terminal 3 - A108-4 (B) Always Below 1 Ω
HWD NO.1 relay holder terminal 4 - A108-1 (E) Always Below 1 Ω
HWD NO.1 relay holder terminal 1 - Body ground Always Below 1 Ω
HWD NO.1 relay holder terminal 4 - Body ground Always Below 1 Ω
A108-1 (E) - Body ground Always Below 1 Ω
HWD NO.1 relay holder terminal 3 or A108-4 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

10.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.2 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.2 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)
a.
E380220C01
2.479,2.375 2.792,2.531 0.313,0.156 10 false *a
*a HWD NO.2 Relay Holder


Disconnect A108 and A123 windshield glass (heated windshield defroster) connectors.


b.

Remove the HWD NO.2 relay from the No. 5 relay block.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO.2 relay holder terminal 5 - Body ground Always 11 to 14 V
HWD NO.2 relay holder terminal 2 - Body ground Front wiperdeicer switch on 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO.2 relay holder terminal 3 - A123-4 (B) Always Below 1 Ω
HWD NO.2 relay holder terminal 4 - A108-3 (E) Always Below 1 Ω
HWD NO.2 relay holder terminal 4 - Body ground Always Below 1 Ω
HWD NO.2 relay holder terminal 1 - Body ground Always Below 1 Ω
A108-3 (E) - Body ground Always Below 1 Ω
HWD NO.2 relay holder terminal 3 or A123-4 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

11.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.3 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.3 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)
E380221C01
1.125,0.073 1.438,0.302 0.313,0.229 12 false *A 4.417,0.063 4.729,0.333 0.313,0.271 12 false *B 1.958,1.896 2.271,2.052 0.313,0.156 10 false *a 5.292,1.917 5.604,2.073 0.313,0.156 10 false *a
*A except 1GD-FTV *B for 1GD-FTV
*a HWD NO.3 Relay Holder - -


a.

Disconnect A109 windshield glass (heated windshield defroster) connector.


b.

Remove the HWD NO.3 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO.3 relay holder terminal 5 - Body ground Always 11 to 14 V
HWD NO.3 relay holder terminal 2 - Body ground Front wiperdeicer switch on 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO.3 relay holder terminal 3 - A109-1 (B) Always Below 1 Ω
HWD NO.3 relay holder terminal 4 - A109-2 (E) Always Below 1 Ω
HWD NO.3 relay holder terminal 4 - Body ground Always Below 1 Ω
HWD NO.3 relay holder terminal 1 - Body ground Always Below 1 Ω
A109-2 (E) - Body ground Always Below 1 Ω
HWD NO.3 relay holder terminal 3 or A109-1 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

12.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.4 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK WIRE HARNESS AND CONNECTOR (HWD NO.4 RELAY - WINDSHIELD GLASS [HEATED WINDSHIELD DEFROSTER] BATTERY AND BODY GROUND)
E380222C01
1.104,0.042 1.417,0.271 0.313,0.229 12 false *A 4.354,0.031 4.646,0.25 0.292,0.219 12 false *B 1.125,1.896 1.438,2.052 0.313,0.156 10 false *a 4.438,1.906 4.75,2.063 0.313,0.156 10 false *a
*A except 1GD-FTV *B for 1GD-FTV
*a HWD NO.4 Relay Holder - -


a.

Disconnect A109 windshield glass (heated windshield defroster) connector.


b.

Remove the HWD NO.4 relay from the No. 1 engine room relay block and No. 1 junction block assembly.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
HWD NO.4 relay holder terminal 5 - Body ground Always 11 to 14 V
HWD NO.4 relay holder terminal 2 - Body ground Front wiperdeicer switch on 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
HWD NO.4 relay holder terminal 3 - A109-3 (B) Always Below 1 Ω
HWD NO.4 relay holder terminal 4 - A109-4 (E) Always Below 1 Ω
HWD NO.4 relay holder terminal 1 - Body ground Always Below 1 Ω
HWD NO.4 relay holder terminal 4 - Body ground Always Below 1 Ω
A109-4 (E) - Body ground Always Below 1 Ω
HWD NO.4 relay holder terminal 3 or A109-3 (B) - Body ground Always 10 kΩ higher



Result:
Proceed to
OK
NG



OK

REPLACE WINDSHIELD GLASS (HEATED WINDSHIELD DEFROSTER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR