Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2017.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1752  Compressor Motor Malfunction  


DESCRIPTION

When the "up" side of the height control switch is pressed, a signal is sent from terminal RC of the suspension control ECU to switch the AIR SUS relay on. As a result, the relay contacts close and the compressor motor turns on, producing compressed air.

The suspension control ECU detects the amount of current flowing to the compressor motor by means of the differences in potential at terminals RM+ and RM- of the suspension control ECU. In this way, the suspension control ECU monitors the compressor motor circuit for abnormalities.

DTC Code DTC Detection Condition Trouble Area
C1752 With the AIR SUS relay activated, a lock signal of the height control compressor motor is detected for 4 seconds or more.
·

AIR SUS fuse

·

Harness or connector

·

Height control compressor

·

Suspension control ECU



WIRING DIAGRAM

C218586E12
0.385,0.594 1.302,0.813 0.917,0.219 10 false from Battery 2.625,0.792 3.229,0.969 0.604,0.177 10 false AIR SUS 2.542,2.354 3.156,2.552 0.615,0.198 10 false AIR SUS 3.448,1.531 3.615,1.698 0.167,0.167 10 false 5 2.052,1.531 2.219,1.698 0.167,0.167 10 false 3 2.073,1.875 2.406,2.042 0.333,0.167 10 false 2 0.927,5.385 1.094,5.552 0.167,0.167 10 false 1 1.104,5.604 1.271,5.771 0.167,0.167 10 false B 3.01,4.594 3.177,4.76 0.167,0.167 10 false 3 3.979,5.375 4.146,5.542 0.167,0.167 10 false 2 3.99,4.854 4.156,5.021 0.167,0.167 10 false 4 3.781,5.583 3.948,5.75 0.167,0.167 10 false E 3.208,4.813 3.594,4.979 0.385,0.167 10 false RM+ 3.646,5.063 4.031,5.229 0.385,0.167 10 false RM- 1.083,6.25 2.948,6.458 1.865,0.208 10 false Height Control Compressor 5.469,6.896 7.042,7.115 1.573,0.219 10 false Suspension Control ECU 5.833,2.667 6.167,2.917 0.333,0.25 10 false R19 5.865,2.458 6.063,2.625 0.198,0.167 10 false 22 5.854,3.677 6.052,3.844 0.198,0.167 10 false 19 6.167,2.656 6.417,2.865 0.25,0.208 10 false RC 6.177,3.875 6.573,4.083 0.396,0.208 10 false RM+ 6.177,4.969 6.573,5.177 0.396,0.208 10 false RM- 5.844,4.781 6.042,4.948 0.198,0.167 10 false 17 1.083,6.083 1.385,6.271 0.302,0.188 10 false S11 5.833,3.885 6.125,4.042 0.292,0.156 10 false A14 5.833,4.979 6.125,5.135 0.292,0.156 10 false A14 3.458,1.896 3.792,2.063 0.333,0.167 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the suspension control ECU, perform registration (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>REGISTRATION).

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:

If DTC C1782 is output at the same time as C1752, perform the inspection necessary for DTC C1782 first (See page Suspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782).


PROCEDURE

1.INSPECT SUSPENSION CONTROL RELAY (AIR SUS)

OK

2.CHECK TERMINAL VOLTAGE (POWER SUPPLY)

NG

REPLACE SUSPENSION CONTROL RELAY (AIR SUS)

2.CHECK TERMINAL VOLTAGE (POWER SUPPLY)
a.

Remove the AIR SUS relay from the engine room relay block.


b.
E371104C06
0.104,0.083 0.417,0.24 0.313,0.156 10 false *a

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Engine room relay block AIR SUS relay terminal 5 - Body ground Always 11 to 14 V


Text in Illustration
*a Component without AIR SUS Relay
(Engine Room Relay Block)



OK

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL COMPRESSOR - AIR SUS RELAY/SUSPENSION CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (HEIGHT CONTROL COMPRESSOR - AIR SUS RELAY/SUSPENSION CONTROL ECU)
a.

Disconnect the S11 height control compressor connector.


b.

Remove the AIR SUS relay from the engine room relay block.


c.

Disconnect the A14 suspension control ECU connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S11-1 (B) - Engine room relay block AIR SUS relay terminal 3 Always Below 1 Ω
S11-1 (B) - Body ground Always 10 kΩ or higher
S11-2 (E) - Body ground Always Below 1 Ω
A14-19 (RM+) - S11-3 (RM+) Always Below 1 Ω
A14-19 (RM+) - Body ground Always 10 kΩ or higher
A14-17 (RM-) - S11-4 (RM-) Always Below 1 Ω
A14-17 (RM-) - Body ground Always 10 kΩ or higher




OK

4.INSPECT HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT HEIGHT CONTROL COMPRESSOR (COMPRESSOR MOTOR)
a.

Remove the height control compressor (See page Suspension>SUSPENSION CONTROL>HEIGHT CONTROL COMPRESSOR>REMOVAL).


b.

Apply 12 V battery voltage to the compressor motor and check the operation of the motor.


C214513E09
1.458,1.115 1.094,0.75 1.094,0.75 0.927,0.75 true 1.969,1.104 2.333,0.75 2.333,0.75 2.5,0.75 true 0.083,0.073 0.354,0.25 0.271,0.177 10 false *a 2.531,0.677 2.677,0.865 0.146,0.188 10 false B 0.813,0.677 0.979,0.865 0.167,0.188 10 false E

OK:
Measurement Condition Specified Condition
12 V battery positive (+) voltage → Terminal 1 (B)
12 V battery negative (-) voltage → Terminal 2 (E)
Motor operates


Text in Illustration
*a Component without harness connected
(Height Control Compressor)

NOTICE:
·

Do not allow the compressor motor to operate for approximately 90 seconds or more.

·

If the compressor is shorted, locked or has a similar type of malfunction, a large amount of current is flowing. Therefore, if the motor does not operate, immediately stop this inspection.




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPLACE HEIGHT CONTROL COMPRESSOR ASSEMBLY