16547
1.INSTALL NO. 1 RADIATOR SUPPORT BUSH
Install the 6 No. 1 radiator support bushes to the radiator assembly.
16548
2.INSTALL NO. 2 RADIATOR SUPPORT BUSH
Install the 2 No. 2 radiator support bushes to the radiator assembly.
16400S
3.INSTALL RADIATOR COLLAR
Install the 4 radiator collars to the radiator assembly.
12209F
4.INSTALL OIL RETURN PIPE SUB-ASSEMBLY (w/o Urea SCR System)
Attach the 2 clamps to install the oil return pipe sub-assembly to the radiator assembly.
17940D
5.INSTALL INTERCOOLER ASSEMBLY (w/o Urea SCR System)
16550
6.INSTALL INTERCOOLER COOLING RADIATOR ASSEMBLY (w/ Urea SCR System)
16562
7.INSTALL NO. 2 RADIATOR TO SUPPORT SEAL
16593
8.INSTALL NO. 1 RADIATOR AIR GUIDE
Install the No. 1 radiator air guide with the 2 bolts.
16563
9.INSTALL NO. 3 RADIATOR TO SUPPORT SEAL
Install a new No. 3 radiator to support seal to the No. 1 radiator guide.
16400
10.INSTALL RADIATOR ASSEMBLY
Insert the tabs of the radiator collar into the radiator service holes.
Install the radiator assembly with the 4 bolts.
53294C
11.INSTALL RADIATOR SIDE DEFLECTOR LH
Attach the 3 claws to install the radiator side deflector LH, and install the clip.
53293C
12.INSTALL RADIATOR SIDE DEFLECTOR RH
Attach the 3 claws to install the radiator side deflector RH, and install the clip.
52521
13.INSTALL FRONT BUMPER CENTER UPPER RETAINER
52119A
14.INSTALL FRONT BUMPER COVER
52129B
15.INSTALL FRONT BUMPER LOWER COVER
16711
16.INSTALL FAN SHROUD
Install the fan pulley.
Place the fan shroud together with the fan with fluid coupling assembly between the engine and radiator assembly.
Be careful not to damage the radiator core.
w/o Urea SCR System:
Attach the 2 guides and install the fan shroud with the 2 bolts.
w/ Urea SCR System:
Attach the 2 guides and install the fan shroud with the 4 bolts.
Temporarily install the fan with fluid coupling assembly to the engine water pump assembly with the 4 nuts.
Make sure to match the paint mark colors on the fan with fluid coupling assembly with the stud bolts of the same color on the engine water pump assembly.
When installing the fan and generator V belt, make sure to securely tighten the nuts of the fan with fluid coupling assembly so that the fan pulley is properly aligned.
Install the fan and generator V belt.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION
Tighten the 4 nuts holding the fan with fluid coupling assembly.
88359
17.INSTALL VISCOUS HEATER V BELT (w/ Viscous Heater)
18.CONNECT OIL COOLER HOSE (for Automatic Transmission)
Connect the oil cooler hose to the radiator assembly and slide the 2 hose clamps to secure the hose.
Attach the 2 clamps and connect the oil cooler hose to the fan shroud with the bolt.
16470
19.INSTALL RADIATOR RESERVOIR ASSEMBLY
Install the radiator reservoir assembly with the 3 bolts.
Attach the 2 clamps to connect the No. 1 water by-pass hose to the fan shroud.
Connect the No. 1 water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.
Connect the No. 2 water by-pass hose to the water inlet and slide the hose clamp to secure the hose.
Attach the 2 clamps to connect the No. 2 water by-pass hose to the fan shroud.
16640
20.INSTALL INTERCOOLER RESERVOIR ASSEMBLY (w/ Urea SCR System)
Install the intercooler reservoir assembly with the 3 bolts.
16554B
21.INSTALL NO. 4 SUB-RADIATOR HOSE (w/ Urea SCR System)
Connect the No. 4 sub-radiator hose to the intercooler reservoir assembly and intercooler cooling water pipe, and slide the 2 hose clamps to secure the hose.
Attach the clamp.
16553B
22.INSTALL NO. 3 SUB-RADIATOR HOSE (w/ Urea SCR System)
Connect the No. 3 sub-radiator hose to the intercooler cooling radiator assembly and intercooler cooling water pipe, and slide the 2 hose clamps to secure the hose.
Attach the clamp.
161B0
23.INSTALL ELECTRIC WATER PUMP ASSEMBLY (w/ Urea SCR System)
Install the electric water pump assembly to the fan shroud with the 2 bolts.
Connect the connector and attach the 4 wire harness clamps, to the electric water pump assembly and fan shroud.
16551B
24.INSTALL NO. 1 SUB-RADIATOR HOSE (w/ Urea SCR System)
Connect the No. 1 sub-radiator hose to the intercooler reservoir assembly and electric water pump assembly, and slide the 2 hose clamps to secure the hose.
Attach the clamp.
16552B
25.INSTALL NO. 2 SUB-RADIATOR HOSE (w/ Urea SCR System)
Connect the No. 2 sub-radiator hose to the intercooler cooling radiator assembly and electric water pump assembly, and slide the 2 hose clamps to secure the hose.
17341K
26.INSTALL INTERCOOLER AIR HOSE (w/o Urea SCR System)
Install the intercooler air hose and tighten the 2 hose bands to secure the hose.
17342F
27.INSTALL NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)
16572D
28.INSTALL NO. 2 RADIATOR HOSE
Install the No. 2 radiator hose and slide the 2 hose clamps to secure the hose.
16571C
29.INSTALL NO. 1 RADIATOR HOSE
Install the No. 1 radiator hose and slide the 2 hose clamps to secure the hose.
82123
30.INSTALL NO. 3 ENGINE WIRE (for Cold Area Specification Vehicles)
Attach the 3 wire harness clamps to connect the No. 3 engine wire to the fan shroud.
Connect the 2 cables to the positive battery terminals.
31.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (for Cold Area Specification Vehicles)
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
32.ADD ENGINE COOLANT (for Urea SCR System)
33.ADD ENGINE COOLANT
34.INSPECT FOR ENGINE COOLANT LEAK (for Urea SCR System)
35.INSPECT FOR ENGINE COOLANT LEAK
51405A
36.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
53292A
37.INSTALL UPPER RADIATOR SUPPORT SEAL
Install the upper radiator support seal with the 13 clips.