Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION ASSEMBLY (for 1GR-FE) › from 2020.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260788 AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE) A

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION ASSEMBLY(for 1GR-FE)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effects/Inoperative when not Performed Link
Battery terminal is disconnected/reconnected Correction of steering angle neutral point Multi-terrain monitor system (Click here)
Gas leaks from exhaust system Inspection after repair Poor idle, engine starting, etc. (Click here)
Automatic transmission assembly Reset memory
·

Large shift shock

·

Engine overruns


(Click here)
Automatic transmission fluid ATF thermal degradation estimate reset The value of the Data List item "ATF Thermal Degradation Estimate" is not estimated correctly.

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane departure alert system Drive the vehicle straight ahead at 40 km/h (25 mph) or more for 10 seconds or more. (Click here)
Pre-collision system
Lighting system (EXT) (for LED Headlight)
Vehicle stability control system (for Hydraulic brake booster) Drive the vehicle straight ahead at 40 km/h (25 mph) or more for at least 10 seconds. (Click here)


CAUTION:
·
A350542

To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.

·
C313282C04
2.573,0.583 2.906,0.583 false 2.948,0.479 3.26,0.677 0.313,0.198 10 false *a
*a Object Exceeding Weight Limit of Transmission Jack


The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

(See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)


Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

Hide 17129 3.REMOVE INTAKE AIR SURGE TANK

Hide 51405A 4.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

Hide 51450 5.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 8.DRAIN ENGINE COOLANT (w/o Air Cooled Transmission Oil Cooler)

Hide 37110 9.REMOVE PROPELLER SHAFT ASSEMBLY

Hide 37140 10.REMOVE FRONT PROPELLER SHAFT ASSEMBLY

Hide 17105 11.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

Hide 17104 12.REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

Hide 28100 13.REMOVE STARTER ASSEMBLY

Hide 11363A 14.REMOVE FLYWHEEL HOUSING SIDE COVER

a.
U148189E01
2.113,0.98 2.055,1.014 false 2.108,0.954 2.074,0.974 false

Remove the flywheel housing side cover from the engine assembly.


Hide 32101A 15.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT

a.
U148190E01
2.117,0.982 2.059,1.015 false 2.112,0.955 2.079,0.976 false

Turn the crankshaft to gain access to the removable locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.

HINT:

There will be one black colored bolt.



Hide 33820B 16.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY

a.
C323981

Remove the clip and nut and disconnect the transmission control cable assembly from the transmission control shaft lever LH and transmission control cable bracket.


Hide 35979B 17.REMOVE TRANSMISSION INSULATOR RH

Hide 18.DISCONNECT OIL COOLER TUBE (w/ ATF Warmer)

a.
C333219

Slide the 2 clips and disconnect the 2 oil cooler hoses from the transmission oil thermostat.

HINT:

Use a container to catch any ATF.



b.
C218114

Remove the 2 bolts and disconnect the 2 oil cooler tubes from the automatic transmission assembly and engine assembly.


Hide 19.DISCONNECT OIL COOLER TUBE (w/o ATF Warmer)

a.
C324534

Disconnect the 2 oil cooler tubes from the automatic transmission assembly.

HINT:

Use a container to catch any ATF.



b.

Remove the 2 bolts and disconnect the 2 oil cooler tubes from the automatic transmission assembly and engine assembly.

C333110


Hide 20.DISCONNECT WATER BY-PASS PIPE (w/ ATF Warmer)

a.
C333095

Slide the 2 clips and disconnect the 2 water by-pass hoses from the transmission oil cooler assembly.

HINT:

Use a container to catch any coolant.



b.

Remove the 2 bolts and disconnect the water by-pass pipe from the automatic transmission assembly.


Hide 51226A 21.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH

a.
C330300

Remove the 8 bolts, front suspension member bracket LH and RH from the No. 3 frame crossmember sub-assembly and vehicle body.


Hide 22.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

a.
C333111

Support the automatic transmission assembly with a transmission jack.

NOTICE:
·

In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.

·

Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.

·

To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.

·

Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.




Hide 51203 23.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C330302

Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.


b.
C213724

Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly from the vehicle body.


Hide 12371 24.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

a.
C330292

Remove the bolt and engine mounting heat insulator from the rear No. 1 engine mounting insulator.


b.
C330291

Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.


Hide 36478A 25.REMOVE TRANSMISSION BREATHER BRACKET

a.
C333112

Tilt down the automatic transmission assembly.

NOTICE:

Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.



b.
C333113

Disconnect the 2 breather hoses and detach the wire harness clamp from the transmission breather bracket.


c.
C333114

Remove the bolt and transmission breather bracket from the automatic transmission assembly.


d.

Remove the clamp from the transmission breather bracket.

HINT:

It is not necessary to remove the transmission clamps they are being replaced.



Hide 26.DISCONNECT WIRE HARNESS

a.
C333126

Disconnect the breather hose from the wire harness.


b.

Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer connector.

C333115

HINT:

Detach the claw, press down the lever, and then disconnect the transmission wire connector.



c.

Detach the heated oxygen sensor connector from the wire harness clamp bracket.


d.

Detach 2 wire harness clamps.


e.

Remove the 4 bolts and disconnect the wire harness from the automatic transmission assembly.


Hide 35000 27.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

a.

Disconnect the breather hose from the engine assembly.


b.
C171497

Remove the 9 bolts and automatic transmission assembly from the engine assembly.

NOTICE:

To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.



Hide 36100 28.REMOVE TRANSFER ASSEMBLY

Hide 33490F 29.REMOVE TRANSMISSION OIL COOLER ASSEMBLY (w/ ATF Warmer)

HINT:

It is not necessary to remove the transmission oil cooler assembly unless it is being replaced.


a.
C333220

Slide the 2 clips and disconnect the 2 oil cooler hoses from the automatic transmission assembly.

HINT:

Use a container to catch any ATF.



b.

Remove the 3 bolts and transmission oil cooler assembly with transmission oil thermostat.


Hide 33823 30.REMOVE TRANSMISSION CONTROL CABLE BRACKET

HINT:

It is not necessary to remove the transmission control cable bracket unless it is being replaced.


a.
C324529

Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.


Hide 3516A 31.REMOVE TRANSMISSION OIL PAN HEAT INSULATOR

HINT:

It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.


a.
C330312

Remove the 3 bolts and transmission oil pan heat insulator from the automatic transmission assembly.


Hide 32.REMOVE TORQUE CONVERTER ASSEMBLY

a.
C324532E02
1.719,0.24 1.125,0.146 1.125,0.146 1.719,0.438 true 0.927,0.021 1.083,0.198 0.156,0.177 10 false *a

Put matchmarks on the automatic transmission assembly and the torque converter assembly.

Text in Illustration
*a Matchmark


b.

Remove the torque converter assembly from the automatic transmission assembly.

NOTICE:

Remove the torque converter assembly from the input shaft horizontally.



Hide 33.REMOVE WIRE HARNESS CLAMP BRACKET

HINT:

It is not necessary to remove the wire harness clamp brackets unless they are being replaced.


a.
C333116

Detach the 8 wire harness clamps and claw and remove the 4 wire harness clamp brackets from the wire harness.


b.
C333121

w/o ATF Warmer:

Remove the bolt and wire harness clamp bracket from the automatic transmission assembly.