1.INSPECT ENGINE COOLANT
2.INSPECT ENGINE OIL
28800
3.INSPECT BATTERY
17801
4.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
Remove the air cleaner cap sub-assembly.
Remove the air cleaner filter element sub-assembly from the air cleaner case.
Visually check that the air filter sub-assembly is not excessively damaged or oily.
If necessary, replace the air cleaner filter element sub-assembly.
Reinstall the air cleaner filter element sub-assembly to the air cleaner case.
Reinstall the air cleaner cap sub-assembly.
19100P
5.INSPECT SPARK PLUG
16361A
6.INSPECT FAN AND GENERATOR V BELT
16620D
7.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY
13750
8.INSPECT VALVE LASH ADJUSTER NOISE
Rev the engine several times. Check that the engine does not emit unusual noises.
If unusual noises occur, warm up the engine and idle it for 30 minutes or more, then perform the preceding inspection.
If any defects or problems are found during the preceding inspection, perform valve lash adjuster assembly inspection (See page Engine / Hybrid System>2TR-FE (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).
9.INSPECT IGNITION TIMING
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Start the engine and idle it.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / IGN Advance.
5 to 15° BTDC @ idle
Refer to the GTS operator's manual for further details.
When checking the ignition timing, the transmission should be in N or P.
Switch off all the accessories and the A/C before connecting the GTS.
Check that the ignition timing advances immediately when the engine speed is increased.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Connect the TC and TE1.
Monitor IGN Advance.
Perform the Active Test.
3 to 7° BTDC @ idle
When checking the ignition timing, the transmission should be in N or P.
Refer to the GTS operator's manual for further details.
When not using the GTS:
Loosen the hose clamp from the throttle body side.
Remove the 3 bolts and disconnect the intake air connector.
Move the intake air connector so that the tester probe of a timing light can be connected to the wire of the ignition coil for the No. 1 cylinder.
Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.
Use a timing light that detects primary signals.
Connect the intake air connector.
Return the parts to their original positions so that the engine can be started.
Start the engine and idle it.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
| *a | Front view of DLC3 |
Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
When checking the ignition timing, the shift lever should be in N or P.
Using the timing light, check the ignition timing.
3 to 7° BTDC @ idle
Turn all the electrical systems and the A/C off.
When checking the ignition timing, the shift lever should be in N or P.
Remove SST from the DLC3.
Check the ignition timing.
5 to 15° BTDC @ idle
Check that the ignition timing advances immediately when the engine speed is increased.
Turn the ignition switch off.
Disconnect the timing light from the engine.
Connect the intake air connector with the 3 bolts.
Tighten the hose clamp.
10.INSPECT ENGINE IDLE SPEED
Warm up and stop the engine.
When using the GTS:
Connect the GTS to the DLC3.
Start the engine and idle it.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
600 to 700 rpm
Turn all the electrical systems and the A/C off.
When checking the idling speed, the shift lever should be in N or P.
Refer to the GTS operator's manual for further details.
Turn the ignition switch off.
Disconnect the GTS from the DLC3.
When not using the GTS:
| *a | Front view of DLC3 |
Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.
Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
Turn all the electrical systems and the A/C off.
When checking the idling speed, the shift lever should be in N or P.
Check the idle speed.
600 to 700 rpm
Disconnect the tachometer probe from the DLC3.
If the engine speed is not as specified, update the idle speed control (ISC) learned value using either procedure 1 or procedure 2 below, and then check the engine speed again.
Procedure 1:
After completely warming up the engine, drive the vehicle at 30 km/h (19 mph) for 30 seconds or more and idle the engine for 30 seconds or more. Repeat this pattern 5 times or more.
| *a | Engine completely warmed up | *b | Vehicle being driven at 30 km/h (19 mph) |
| *c | Idling | *d | 1 time |
Procedure 2:
After completely warming up the engine, stop the engine and then idle it. Repeat this pattern 5 times or more.
| *a | Engine completely warmed up | *b | Engine stopped |
| *c | Engine started | *d | Idling |
| *e | 1 time | - | - |
Be sure to idle the engine for 150 seconds or more for each time the pattern is repeated.
If the engine speed is not as specified after performing the procedure above, inspect the idle speed control system as it is malfunctioning.
11.INSPECT COMPRESSION
Warm up and stop the engine.
Check for DTCs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
Disconnect the 4 fuel injector connectors.
Remove the 4 spark plugs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>REMOVAL).
Inspect the cylinder compression pressure.
Fully open the throttle.
While cranking the engine, measure the compression pressure.
1230 kPa (12.5 kgf/cm2, 178 psi) or higher
880 kPa (9.0 kgf/cm2, 128 psi)
98 kPa (1.0 kgf/cm2, 14.2 psi) or less
Use a fully-charged battery so the engine speed can be increased to 250 rpm or more.
Inspect the other cylinders in the same way.
Measure the compression in as short a time as possible.
If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and inspect it again.
If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.
If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.
Install the 4 spark plugs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>IGNITION COIL AND SPARK PLUG>INSTALLATION).
Connect the 4 fuel injector connectors.
Clear the DTCs (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).
12.INSPECT CO/HC
Start the engine.
Run the engine at 2500 rpm for approximately 180 seconds.
Insert a CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe while idling the engine.
Check the CO/HC concentration during idling and when the engine is running at 2500 rpm.
When doing the 2 mode (with the engine idling/ running at 2500 rpm) test, the measuring procedures are determined by applicable local regulations.
If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.
Check the air fuel ratio sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION) and heated oxygen sensor (See page Engine / Hybrid System>2TR-FE (ENGINE CONTROL)>HEATED OXYGEN SENSOR>INSPECTION).
Refer to the table below for possible causes, and then inspect the applicable parts and repair them if necessary.
| CO | HC | Problems | Possible Causes |
|---|---|---|---|
| Normal | High | Rough idling | 1.
Faulty ignition: -
Incorrect timing -
Plugs are contaminated or shorted, or gaps are incorrect 2.
Incorrect valve clearance (valve lash adjuster assembly) 3.
Leakage from intake or exhaust valves 4.
Leakage from cylinders |
| Low | High | Rough idling
(Fluctuating HC reading) |
1.
Vacuum leaks: -
PCV hoses -
Intake manifold -
Throttle body with motor assembly -
Brake booster line 2.
Lean mixture causing misfire |
| High | High | Rough idling
(Black smoke from exhaust) |
1.
Restricted air cleaner filter element sub-assembly 2.
Plugged PCV valve sub-assembly 3.
Faulty SFI system: -
Faulty fuel pressure regulator assembly -
Faulty engine coolant temperature sensor -
Faulty mass air flow meter sub-assembly -
Faulty ECM -
Faulty fuel injector assemblies -
Faulty throttle body with motor assembly |