Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › LUBRICATION SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053690 1GD-FTV LUBRICATION _0260705 LUBRICATION SYSTEM G

1GD-FTV LUBRICATION  LUBRICATION SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT ENGINE OIL QUALITY

a.

Check the engine oil for deterioration, water contamination, discoloration or thinning. If the quality is visibly poor, replace the engine oil and oil filter sub-assembly.


Hide 2.INSPECT ENGINE OIL LEVEL

a.

Warm up the engine, and then stop the engine and wait 5 minutes.


b.

Check that the engine oil level is between the engine oil level dipstick low level mark and full level mark.

If the engine oil level is low, check for leaks and add engine oil to the full level mark.

NOTICE:

Do not fill engine oil above the full level mark.


HINT:

A certain amount of engine oil will be consumed while driving. In the following situations, oil consumption may increase, and engine oil may need to be refilled in between oil maintenance intervals.

·

When the engine is new, for example directly after purchasing the vehicle or after replacing the engine.


·

If low quality oil or oil of an inappropriate viscosity is used.


·

When driving at a high engine speed or with a heavy load, when towing, or when driving while accelerating or decelerating frequently.


·

When idling for a long time, or when driving frequently through heavy traffic.


When judging the amount of oil consumption, keep in mind that the oil may have become diluted, making it difficult to judge the true level accurately.



Hide 3.INSPECT OIL PRESSURE (w/ 2 Stage Hydraulic Switching Oil Pump System)

a.

Check the condition of the oil pressure warning light and oil level warning light.

NOTICE:

If the ignition switch is turned off, the warning lights do not illuminate the next time the engine is started. Therefore, checking the vehicle after it has been brought in for service will not be of any use for troubleshooting. It is essential to ask the customer whether the warning lights were illuminated or not when the malfunction occurred.


- Condition 1 Condition 2 Condition 3 Condition 4
Oil Pressure Warning Light Illuminated Illuminated Illuminated Illuminated
Oil Level Warning Light Illuminated Illuminated Not illuminated Not illuminated
DTC Output (MIL does not illuminate) P052477 None P052477 None
Possible Cause
·

Intake of air into an oil line due to a decrease in the amount of engine oil, or oil pressure stuck at low value (a DTC is stored as the oil pressure does not increase when the system switches to high oil pressure control mode)

·

Clogging in an oil line (the oil strainer, etc.), or a problem with the oil pump


·

Intake of air into an oil line due to a decrease in the amount of engine oil

·

Clogging in an oil line (the oil strainer, etc.), or a problem with the oil pump


·

Oil pressure stuck at low value (a DTC is stored as the oil pressure does not increase when the system switches to high oil pressure control mode)

·

Clogging in an oil line (the oil strainer, etc.), or a problem with the oil pump


Clogging in an oil line (the oil strainer, etc.), or a problem with the oil pump
Solution to Problem
·

Add engine oil so that the oil level is within the specified range and perform an oil pressure control system check. If the results of the check are normal, it is likely that the illumination of the warning light was caused by oil consumption (if the amount of oil consumption is large, check the oil consumption and perform repairs). If the results of the check are abnormal, it is likely that the problem was caused by the oil pressure control system being stuck in low pressure oil control mode.

-

(Click here)

-

w/ DPF:

(Click here)

-

w/ Urea SCR System:

(Click here)


·

Perform an oil pressure inspection. If the results are abnormal, repair the engine.


·

Perform the inspection procedure for DTC P052477.

-

(Click here)

-

w/ DPF:

(Click here)

-

w/ Urea SCR System:

(Click here)


·

Perform an oil pressure inspection. If the results are abnormal, repair the engine.


Perform an oil pressure inspection. If the results are abnormal, repair the engine.

HINT:
·

Under normal conditions, the oil pressure warning light and oil level warning light are not illuminated.

·

When performing a check of the oil pressure control system, if the system does not switch from high oil pressure control mode, one of the following may be the cause of the problem.

-

The sleeve valve is locked in the position for high oil pressure.

-

The EFI-MAIN No. 2 relay is malfunctioning.

-

The oil pressure switching valve is stuck off.


·

If a DTC is stored but the cause of the problem cannot be found, either of the following may be the cause of the problem.

-

Engine oil was added by the customer due to a lack of engine oil.

-

The system was temporarily stuck in low oil pressure control mode (foreign matter was stuck in the system, etc.)


·

Check the oil pressure control system using the following procedure.




b.

Check the oil pressure control system (when using the GTS).

Reference:
Purpose of Check When to Perform Check
This check is used to check whether the oil pressure control system is operating properly when the oil pressure switching valve is forcibly operated. Perform this check when DTC P052477 is output.


i.

Connect the GTS to the DLC3.


ii.

Start the engine and warm it up.

HINT:

Confirm that the engine coolant temperature is 70 to 89°C (158 to 192°F), as the oil pressure changes according to the engine coolant temperature.



iii.

Enter the following menus: Powertrain / Engine and Transmission / Utility / Engine Oil Pressure Control Check.

Powertrain > Engine and Transmission > Utility
Tester Display
Engine Oil Pressure Control Check
50005 372 4620

iv.

Check the following table and perform the oil pressure control system check.

HINT:
·

Even when the engine is warmed up, there are some instances where the oil pressure control system check cannot be performed.

·

The engine speed will increase during the oil pressure control system check.



Item Condition Content of Check System Operation
Oil Pressure Control System Check
·

Engine is idling

·

Vehicle is stopped

·

Shift lever is in P (for Automatic Transmission)

·

Shift lever is in neutral (for Manual Transmission)

·

Engine coolant temperature is in specified range


1.

Valve turns off (high oil pressure control mode)

2.

Valve turns on (low oil pressure control mode)

3.

Valve turns off (high oil pressure control mode)


The average oil pressure is over 1 second when the valve is operated is displayed.
Details:
The oil pressure is measured for 1 second when the valve is operated, and the value measured every 0.1 seconds is displayed for each valve state [(1) to (3)].


v.

Read the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values.

Reference Oil Pressure:
Item Specified Condition
Valve Off (High Pressure Control Mode) 250 to 510 kPa (2.5 to 5.2 kgf/cm2, 36 to 74 psi)
Valve On (Low Pressure Control Mode) 100 to 250 kPa (1.0 to 2.5 kgf/cm2, 15 to 36 psi)



vi.

Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.

Standard:

50 kPa (0.5 kgf/cm2, 7.3 psi) or higher


A246226C04
0.349,1.076 0.543,1.241 0.194,0.165 10 *a 1.404,0.769 1.598,0.934 0.194,0.165 10 *e 1.404,1.46 1.598,1.625 0.194,0.165 10 *f 1.404,2.024 1.598,2.189 0.194,0.165 10 *g 1.404,2.568 1.598,2.733 0.194,0.165 10 *h 1.418,3.141 1.612,3.306 0.194,0.165 10 *i 1.418,3.681 1.612,3.846 0.194,0.165 10 *j 1.404,4.509 1.598,4.674 0.194,0.165 10 *k 1.418,5.058 1.612,5.223 0.194,0.165 10 *l 3.092,4.025 3.286,4.190 0.194,0.165 10 *m 4.166,4.025 4.359,4.190 0.194,0.165 10 *m 5.278,4.025 5.472,4.190 0.194,0.165 10 *m 0.349,2.307 0.543,2.472 0.194,0.165 10 *b 0.349,3.425 0.543,3.590 0.194,0.165 10 *c 0.349,4.807 0.543,4.972 0.194,0.165 10 *d
*a Oil Pressure Sensor Output *b Engine Speed
*c Oil Pressure Control Mode (State of Oil Pressure Switching Valve) *d Active Test Activation Request
*e High Oil Pressure *f Low Oil Pressure
*g 2000 rpm *h Idle Speed
*i On (Low Oil Pressure Control Mode) *j Off (High Oil Pressure Control Mode)
*k On *l Off
*m Approximately 5 seconds - -




c.

Check the oil pressure control system (when not using the GTS).

HINT:

When not using the GTS, it is not possible to determine whether the system is stuck in high oil pressure control mode.


i.

Inspect the oil pressure according to the procedure listed below under "Inspect Engine Oil Pressure".

Standard Oil Pressure:
Condition Specified Condition
Idling 50 kPa (0.5 kgf/cm2, 7.3 psi) or higher
Engine running at 2500 rpm 250 kPa (2.5 kgf/cm2, 36 psi) or higher
Engine running at 3500 rpm 350 kPa (3.6 kgf/cm2, 51 psi) or higher


HINT:

The possible cause can be determined based on the results of the oil pressure inspection (refer to the following table).


Measurement Results:
- Condition 1 Condition 2
Idling Normal Abnormal
2500 rpm Abnormal Abnormal
3500 rpm Abnormal Abnormal
Possible Cause Oil pressure control stuck in low oil pressure control mode Clogging in an oil line (the oil strainer, etc.), or a problem with the oil pump




Hide 4.INSPECT ENGINE OIL PRESSURE (w/ 2 Stage Hydraulic Switching Oil Pump System)

CAUTION:
·

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not remove the oil pressure sender gauge assembly while the engine is hot.



a.

Remove the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL


b.
A339684C01
1.917,0.531 2.385,0.531 true 0.844,0.448 1.01,0.448 1.01,0.448 1.417,1.104 true 1.698,0.448 1.906,0.635 0.208,0.188 10 true *a 0.594,0.365 0.844,0.552 0.25,0.188 10 true *b
*a Oil Pressure Gauge
*b Adapter


Install an oil pressure gauge with the adapter.

NOTICE:

Before and after measurement, clean equipment and hoses.



c.

Warm up the engine.

HINT:

Confirm that the engine coolant temperature is 70°C (158°F) or higher after the engine is warmed up, as the oil pressure changes according to the engine coolant temperature.



d.

Measure the engine oil pressure.

Standard Engine Oil Pressure:
Condition Specified Condition
Idle 50 kPa (0.5 kgf/cm2, 7.3 psi) or higher
2500 rpm 250 kPa (2.5 kgf/cm2, 36 psi) or higher
3500 rpm 350 kPa (3.6 kgf/cm2, 51 psi) or higher


HINT:

When the oil pressure sender gauge assembly is removed, the oil pressure control system operates in high oil pressure control mode.



e.

Remove the oil pressure gauge and adapter.


f.

Install the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SENSOR>INSTALLATION



Hide 5.INSPECT ENGINE OIL PRESSURE (w/o 2 Stage Hydraulic Switching Oil Pump System)

CAUTION:
·

To prevent injury due to contact with an operating fan and generator V-belt or cooling fan, keep your hands and clothing away from the fan and generator V-belt and cooling fans when working in the engine compartment with the engine running.

·

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.

·

To prevent burns, do not remove the engine oil pressure switch assembly while the engine is hot.



a.

Remove the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCH>REMOVAL


b.
A339684C01
1.917,0.531 2.385,0.531 true 0.844,0.448 1.01,0.448 1.01,0.448 1.417,1.104 true 1.698,0.448 1.906,0.635 0.208,0.188 10 true *a 0.594,0.365 0.844,0.552 0.25,0.188 10 true *b
*a Oil Pressure Gauge
*b Adapter


Install an oil pressure gauge with the adapter.

NOTICE:

Before and after measurement, clean equipment and hoses.



c.

Warm up the engine.


d.

Measure the engine oil pressure, and check that it is within the standard range.

Standard Engine Oil Pressure:
Condition Specified Condition
Idle 29 kPa (0.3 kgf/cm2, 4.2 psi) or higher
3000 rpm 245 kPa (2.5 kgf/cm2, 36 psi) or higher


If the result is not as specified, check the quality of the engine oil and check the oil paths for clogging. Repair or replace if necessary. If the engine oil pressure is still not as specified, replace the timing chain case assembly.

HINT:

Replace the timing chain case assembly as the engine oil pump is built into the timing chain case assembly.



e.

Remove the oil pressure gauge and adapter.


f.

Install the engine oil pressure switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCH>INSTALLATION