Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260523 ENGINE G

1GD-FTV ENGINE MECHANICAL  ENGINE  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 16620 4.INSPECT V-RIBBED BELT TENSIONER ASSEMBLY

Hide 5.CHECK VALVE LASH ADJUSTER NOISE

a.

Rev the engine several times. Check that the engine does not emit unusual noises.

If unusual noises occur, warm up the engine and idle it for more than 30 minutes. Then perform the inspection above again.

If any defects or problems are found during the inspection above, perform a valve lash adjuster inspection (See page Engine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>ENGINE UNIT>INSPECTION).


Hide 17801 6.INSPECT AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Remove the air cleaner cap.


b.

Remove the air cleaner filter element sub-assembly from the air cleaner case.


c.

Visually check that the air filter sub-assembly is not excessively damaged or oily.

If necessary, replace the air cleaner filter element sub-assembly.


d.

Reinstall the air cleaner filter element sub-assembly to the air cleaner case.


e.

Reinstall the air cleaner cap.


Hide 7.INSPECT ENGINE IDLE SPEED

a.

Warm up and stop the engine.


b.

Connect the GTS to the DLC3.


c.

Start the engine and idle it.


d.

Enter the following menus: Powertrain / Engine and Transmission / Data List / Engine Speed.


e.

Inspect the engine idle speed.

Standard idle speed:

610 to 750 rpm


NOTICE:
·

Turn all the electrical systems and A/C off.

·

When checking the idle speed, move the shift lever to neutral.



HINT:
·

For more information about the GTS, refer to its operator's manual.

·

If the GTS is not available, use a tachometer as a substitute.




f.

Turn the ignition switch off.


g.

Disconnect the GTS from the DLC3.


Hide 8.INSPECT MAXIMUM SPEED

a.

Start the engine.


b.

Fully depress the accelerator pedal.


c.

Check the maximum engine speed.

Maximum engine speed:

4450 to 4750 rpm



Hide 9.INSPECT COMPRESSION

a.

Warm up and stop the engine.


b.

Remove the 4 injector assemblies (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL).


c.

Inspect the cylinder compression pressure.

i.
A340280E02
1.479,0.802 0.781,0.802 false 1.521,0.344 0.823,0.344 false 2.438,1.417 1.74,1.417 false 1.344,1.313 1.021,1.552 1.021,1.552 0.75,1.552 false 1.729,1.896 2.042,1.656 2.042,1.656 2.188,1.656 false 1.719,2.198 2.177,2.385 2.177,2.385 2.406,2.385 true 1.76,2.917 2.219,3.104 2.219,3.104 2.458,3.104 true 0.563,0.24 0.719,0.417 0.156,0.177 10 false *1 0.552,0.698 0.708,0.875 0.156,0.177 10 false *2 0.51,1.458 0.667,1.635 0.156,0.177 10 false *3 2.469,1.323 2.625,1.5 0.156,0.177 10 false *a 2.229,1.552 2.385,1.729 0.156,0.177 10 false *b 2.427,2.271 2.583,2.448 0.156,0.177 10 true *c 2.479,3 2.635,3.177 0.156,0.177 10 true *d

Install a new nozzle holder gasket, new injection nozzle seat, new O-ring, SST (attachment I), nozzle holder clamp and washer to the cylinder head cover sub-assembly with the bolt.

SST
09992-19015  (09992-10120)

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)

Text in Illustration
*1 Bolt
*2 Washer
*3 Nozzle Holder Clamp
*a SST (Attachment I)
*b New O-Ring
*c New Injection Nozzle Seat
*d New Nozzle Holder Gasket


ii.
A340281E01
0.83,0.433 1.438,0.433 false 2.101,1.491 2.413,0.942 2.413,0.942 2.575,0.942 false 1.46,0.334 1.650,0.506 0.190,0.173 10 *a 2.587,0.852 2.777,1.024 0.190,0.173 10 *b

Connect SST (gauge assembly), SST (packing set) and SST (L-joint) to SST (attachment I).

SST
09992-19015  (09992-10010, 09992-10020, 09992-10030)

Text in Illustration
*a SST (Compression Gauge)
*b SST (L-Joint)


iii.

While cranking the engine, measure the compression pressure.

Standard compression pressure:

2700 kPa (27.5 kgf/cm2, 392 psi) or higher


Minimum pressure:

2200 kPa (22.4 kgf/cm2, 319 psi)


Difference between each cylinder:

500 kPa (5.1 kgf/cm2, 73 psi) or less


NOTICE:
·

Use a fully-charged battery so the engine speed can be increased to 280 rpm or more.

·

Inspect the other cylinders in the same way.

·

Measure the compression as quickly as possible.




iv.

If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the injector holes, and then inspect it again.

If adding oil increases the compression pressure, the piston rings and/or cylinder bore may be worn or damaged.

If the pressure stays low, the valve may be stuck or seated improperly, or there may be leakage from the gasket.



d.

Remove SST.


e.

Install the 4 injector assemblies (See page Engine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>INSTALLATION).