Home › Engine / Hybrid System › 1GD-FTV (LUBRICATION) › OIL AND OIL FILTER › from 2020.08
RM27T0E _51 Engine / Hybrid System _053690 1GD-FTV LUBRICATION _0260706 OIL AND OIL FILTER A

1GD-FTV LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


PROCEDURE

Hide 51450 1.REMOVE REAR ENGINE UNDER COVER ASSEMBLY

Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap assembly.


b.

Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.


c.

Clean and install a new gasket and the oil pan drain plug.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)


Hide 3.REMOVE WIRING HARNESS CLAMP BRACKET (w/ Urea SCR System)

Hide 15601 4.REMOVE OIL FILTER SUB-ASSEMBLY

a.
A339689E01
2.271,0.865 2.688,0.865 true 2.75,0.781 3.083,0.979 0.333,0.198 10 true SST

Using SST, remove the oil filter sub-assembly.

SST
09228-07502  

HINT:
·

Before removing the oil filter sub-assembly, place cloth where the oil may splash.


·

Use a container to catch the draining engine oil.




Hide 15601 5.INSTALL OIL FILTER SUB-ASSEMBLY

a.

Check and clean the oil filter sub-assembly installation surface.


b.

Apply clean engine oil to the gasket of a new oil filter sub-assembly.


c.

Lightly screw the oil filter sub-assembly into place by hand. Tighten it until the gasket contacts the seat.


d.
A339683E02
2.583,0.167 2.74,0.167 2.74,0.167 2.792,0.625 true 2.229,0.083 2.583,0.26 0.354,0.177 10 true SST

Using SST, tighten the oil filter sub-assembly.

Text in Illustration
V100135

3/4 Turn

SST
09228-07502  


e.

Depending on the space available, choose from the following.

If enough space is available, use a torque wrench to tighten the oil filter sub-assembly.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


f.

If enough space is not available to use a torque wrench, tighten the oil filter sub-assembly 3/4 of a turn by hand or with a common wrench.


Hide 6.INSTALL WIRING HARNESS CLAMP BRACKET (w/ Urea SCR System)

Hide 7.ADD ENGINE OIL

a.

Add new engine oil and install the oil filler cap assembly.

Standard Oil Grade:
Item Oil Grade Oil Viscosity (SAE)

*: Using engine oil other than ACEA C2 or ACEA C5 may damage the catalytic converter

w/ DPF ACEA C2* - 0W-30
- 5W-30
ACEA C5* - 0W-20
w/o DPF API CF-4, CF or ACEA B3, B4, B5 or JASO DL-0 - 5W-30
- 10W-30


Standard Capacity:
Item Specified Condition
Drain and refill without oil filter sub-assembly change 7.2 liters (7.6 US qts, 6.3 Imp. qts)
Drain and refill with oil filter sub-assembly change 7.7 liters (8.1 US qts, 6.8 Imp. qts)
Dry fill 8.6 liters (9.1 US qts, 7.6 Imp. qts)



Hide 8.INSPECT FOR OIL LEAK

a.

Start the engine. Make sure that there are no oil leaks from the areas that were worked on.