Home › Engine / Hybrid System › 1GD-FTV (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.08
RM27T0E _51 Engine / Hybrid System _053665 1GD-FTV ENGINE MECHANICAL _0260529 ENGINE ASSEMBLY A

1GD-FTV ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 12361 1.INSTALL FRONT ENGINE MOUNTING INSULATOR (for LH Side)

a.

Install the front engine mounting insulator to the front engine mounting bracket with the nut.

Torque:
86 N*m (877 kgf*cm, 63 ft.*lbf)


b.

Connect the vacuum hose to the front engine mounting insulator.


Hide 82121 2.INSTALL ENGINE WIRE

a.

Install the engine wire to the engine assembly.


Hide 4.REMOVE ENGINE ASSEMBLY TO ENGINE STAND

NOTICE:
·

Pay attention to the angle of the sling device as the engine assembly or engine hangers may be damaged or deformed if the angle is incorrect.

·

With the exception of installing the engine assembly to an engine stand or removing the engine assembly from an engine stand, do not perform any work on the engine assembly while it is suspended, as doing so is dangerous.



a.

Attach the engine sling device and hang the engine assembly with the chain block.


b.

Remove the engine assembly from the engine stand.


Hide 5.INSTALL ENGINE ASSEMBLY

a.

Slowly lower the engine assembly into the engine compartment.


b.
A246132E02
0.479,3.313 0.719,3.313 0.719,3.313 1.01,3.615 true 1.885,3.313 2.042,3.313 2.042,3.313 2.25,3.615 true 1.115,3.927 1.375,4.188 1.375,4.188 1.563,4.188 true 2.375,3.969 2.635,4.219 2.635,4.219 2.823,4.219 true 1.125,2.729 1.281,2.906 0.156,0.177 10 false *a 2.375,2.719 2.531,2.896 0.156,0.177 10 false *b 0.208,3.229 0.365,3.406 0.156,0.177 10 false *1 1.656,3.208 1.813,3.385 0.156,0.177 10 false *1 1.604,4.094 1.76,4.271 0.156,0.177 10 false *2 2.844,4.104 3,4.281 0.156,0.177 10 false *2

Install the engine assembly to the body with the 4 bolt and 4 nuts.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)

HINT:

For RHD vehicles only:

When tightening the nut closer to the rear of the vehicle for the engine mounting bracket on the right side, make sure that the claw (stopper) of the bolt does not protrude past the rear edge of the bracket.


Text in Illustration
*1 Claw (Stopper)
*2 Bracket
*a Correct
*b Incorrect


c.

Remove the 3 bolts, No. 1 engine hanger upper and No. 2 engine hanger.


Hide 11355 6.INSTALL REAR END PLATE

a.

Install the rear end plate to the cylinder block sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13405 7.INSTALL FLYWHEEL SUB-ASSEMBLY

a.

Clean the bolts and their holes.


b.
A349457E02
2.019,0.794 2.5,1.123 2.5,1.123 2.918,1.123 false 1.194,0.9 0.81,1.283 0.81,1.283 0.5,1.283 false 2.947,1.033 3.234,1.214 0.287,0.181 10 SST 0.145,1.199 0.432,1.380 0.287,0.181 10 SST

Using SST, hold the crankshaft pulley.

SST
09213-58014  
09330-00021  


c.

for Manual Transmission:

Install the flywheel sub-assembly to the crankshaft with the 8 bolts.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)

NOTICE:

Do not start the engine for at least 1 hour after installation.



d.
A346662E01
0.094,0.746 0.250,0.927 0.156,0.181 10 *a 3.061,0.682 3.217,0.864 0.156,0.181 10 *b 0.157,0.075 0.313,0.256 0.156,0.181 10 *1 2.784,0.324 2.939,0.506 0.156,0.181 10 *3 0.362,0.148 0.557,0.148 0.557,0.148 0.82,0.377 false 2.165,0.141 2.321,0.322 0.156,0.181 10 *2 2.104,0.24 1.995,0.24 1.995,0.24 1.805,0.43 false 2.76,0.426 2.651,0.426 2.651,0.426 2.461,0.616 false

for Automatic Transmission:

Install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft with the 8 bolts.

NOTICE:
·

Align either hole in the pump impeller drive plate and either hole in the rear drive plate spacer with the knock pin of the flywheel sub-assembly, and then install the flywheel sub-assembly, the pump impeller drive plate and the rear drive plate spacer to the crankshaft.

·

Do not start the engine for at least 1 hour after installation.



HINT:

As the rear drive plate spacer and pump impeller drive plate are not reversible, be sure to install them in the direction shown in the illustration.


Text in Illustration
*1 Flywheel Sub-assembly
*2 Pump Impeller Drive Plate
*3 Rear Drive Plate Spacer
*a Engine Side
*b Transmission Side


e.
A344484E02
1.74,1.76 1.865,1.958 0.125,0.198 10 true 1 1.813,0.365 1.948,0.542 0.135,0.177 10 true 2 1.094,1.146 1.219,1.344 0.125,0.198 10 true 3 2.406,0.938 2.531,1.125 0.125,0.188 10 true 4 1.281,0.563 1.406,0.74 0.125,0.177 10 true 5 2.198,1.531 2.333,1.719 0.135,0.188 10 true 6 2.26,0.552 2.385,0.729 0.125,0.177 10 true 7 1.219,1.604 1.365,1.792 0.146,0.188 10 true 8

for Automatic Transmission:

Install and uniformly tighten and tighten the 8 bolts in several steps in the sequence shown in the illustration.

Torque:
178 N*m (1815 kgf*cm, 131 ft.*lbf)


f.

w/o Viscous Heater:

Install the crankshaft pulley cover to the crankshaft pulley with the 4 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


g.

w/ Viscous Heater:

Install the crankshaft pulley cover and viscous heater crankshaft pulley to the crankshaft pulley with the 4 bolts.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


Hide 31250 8.INSTALL CLUTCH DISC ASSEMBLY (for Manual Transmission)

Hide 31210 9.INSTALL CLUTCH COVER ASSEMBLY (for Manual Transmission)

Hide 31210 10.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 35000 11.INSTALL AUTOMATIC TRANSMISSION ASSEMBLY (for Automatic Transmission)

Hide 32101A 12.INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT (for Automatic Transmission)

Hide 33030 13.INSTALL MANUAL TRANSMISSION UNIT ASSEMBLY (for Manual Transmission)

Hide 37110 14.INSTALL PROPELLER SHAFT ASSEMBLY

Hide 37140 15.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 17410 16.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 87120G 17.INSTALL VISCOUS HEATER WITH MAGNET CLUTCH ASSEMBLY (w/ Viscous Heater)

a.

Install the viscous heater with magnet clutch assembly to the No. 1 viscous heater bracket with the 2 bolts.

Torque:
39 N*m (398 kgf*cm, 29 ft.*lbf)


b.

Connect the connector to the viscous heater with magnet clutch assembly.


Hide 87209B 18.INSTALL WATER HOSE SUB-ASSEMBLY B (w/ Viscous Heater)

a.

Install the water hose sub-assembly B to the No. 2 water pipe and water outlet sub-assembly, slide the 4 clamps secure the hoses.


b.

Connect the water hose sub-assembly B to the water inlet with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 88320 19.CONNECT COOLER COMPRESSOR ASSEMBLY

a.

Temporarily install the cooler compressor assembly and stud bolt to the compressor mounting bracket.


b.

Using an E8 "TORX" socket wrench, tighten the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Install the 3 bolts and nut.

Torque:
25 N*m (250 kgf*cm, 18 ft.*lbf)


d.

Connect the connector to the cooler compressor assembly.


Hide 44310 21.CONNECT VANE PUMP ASSEMBLY

a.

Connect the vane pump assembly to the generator bracket with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


b.

w/ Power Steering Oil Pressure Switch:

Connect the 2 connectors to the vane pump assembly.


Hide 87209 22.INSTALL WATER HOSE SUB-ASSEMBLY

Hide 74431 23.INSTALL BATTERY TRAY

Hide 28800 24.INSTALL BATTERY

Hide 74481 25.INSTALL BATTERY HOLD DOWN CLAMP

a.

Install the battery hold down clamp with the 2 nuts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 82121 26.CONNECT ENGINE WIRE

a.

Connect the engine room main wire to the battery with the nut.

Torque:
7.5 N*m (76 kgf*cm, 66 in.*lbf)


b.

Attach the clamp.


c.

Connect the No. 2 engine wire to the body with the bolt.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


d.

Attach the 2 claws and install the nut.

Torque:
11 N*m (112 kgf*cm, 8 ft.*lbf)


e.

Attach the 3 claws to install the No. 1 relay block cover upper.


Hide 23273H 27.CONNECT NO. 2 FUEL HOSE

a.

Connect the No. 2 fuel hose to the No. 3 nozzle leakage pipe, slide the clamp to secure the hose.


b.

Install the 2 clamps to the No. 2 fuel hose.


Hide 23271H 28.CONNECT NO. 1 FUEL HOSE

a.

Connect the No. 1 fuel hose to the No. 2 fuel pipe, slide the clamp to secure the hose.


b.

Install the clamp to the No. 1 fuel hose.


Hide 44306 29.CONNECT VANE PUMP OIL RESERVOIR SUB-ASSEMBLY

Hide 77820 30.CONNECT UREA TANK FILLER PIPE ASSEMBLY (w/ Urea SCR System)

Hide 17342F 31.INSTALL NO. 2 INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17341K 32.INSTALL INTERCOOLER AIR HOSE (w/o Urea SCR System)

Hide 17801 34.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

Hide 17940D 36.INSTALL INTERCOOLER ASSEMBLY (w/ Urea SCR System)

Hide 12601B 37.INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY (w/o Urea SCR System)

Hide 82121 38.CONNECT ENGINE WIRE

a.
A226129E03
3.007,0.331 3.191,0.510 0.184,0.179 10 *1 2.912,1.633 3.096,1.812 0.184,0.179 10 *2 2.975,0.427 2.841,0.427 2.841,0.427 2.611,0.751 false 2.414,1.25 2.68,1.725 2.68,1.725 2.895,1.725 false

Attach the grommet to the wire harness support.

Text in Illustration
*1 Grommet
*2 Wire Harness Support


b.
A225402E04
0.031,0 0.265,0.188 0.235,0.188 10 *A 1.83,0 2.064,0.188 0.235,0.188 10 *B

Pass the wire harness into the vehicle and install the wire harness support.

Text in Illustration
*A for LHD
*B for RHD


c.

Attach the clamp and connect the engine wire to the bracket.



Hide 16400 39.INSTALL RADIATOR ASSEMBLY

Hide 55781E 40.INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

Hide 53301 41.INSTALL HOOD SUB-ASSEMBLY

a.
A358217

Install the hood sub-assembly with the 8 bolts.

Torque:
Bolt A : 13 N*m (133 kgf*cm, 10 ft.*lbf)
Bolt B : 18 N*m (178 kgf*cm, 13 ft.*lbf)

Text in Illustration
V100135

Bolt A
V100136

Bolt B


b.

Connect the washer nozzle hose.


Hide 53301 42.ADJUST HOOD SUB-ASSEMBLY

Hide 43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 44. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 46.ADD AUTOMATIC TRANSMISSION FLUID (for Automatic Transmission)

Hide 47.ADD MANUAL TRANSMISSION OIL (for Manual Transmission)

Hide 48.PERFORM REGISTRATION

a.

Perform registration of injector compensation codes. (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION)


b.

Perform registration of pilot quantity learning. (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>REGISTRATION)


Hide 55.INSPECT ENGINE IDLE SPEED AND MAXIMUM SPEED

Hide 51450 56.INSTALL REAR ENGINE UNDER COVER ASSEMBLY

a.

Install the rear engine under cover with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51495 57.INSTALL TRANSMISSION UNDER COVER

a.

Install the transmission under cover with the 2 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 51405A 58.INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

a.

Install the No. 1 engine under cover with the 4 bolts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 52129B 59.INSTALL FRONT BUMPER LOWER COVER

a.

Install the front bumper lower cover with the clip and 5 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)