If there is a short in a speaker circuit, the radio and display receiver assembly detects it and stops output to the speakers.
As a result, sound cannot be heard from the speakers even if there is no malfunction in the radio and display receiver assembly or speakers.
If there is a short in a speaker circuit, the stereo component amplifier assembly detects it and stops output to the speakers.
As a result, sound cannot be heard from the speakers even if there is no malfunction in the stereo component amplifier assembly, DCM (telematics transceiver)* or speakers.
*: w/ Telematics Transceiver
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Audio and Visual System.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for 6 Speakers | A |
| for 9 Speakers | B |
A
B
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly or front No. 2 speaker assembly | A |
| Rear speaker assembly | B |
If sound cannot be heard from any speaker, inspect all of them.
A
B
Disconnect the H95 radio and display receiver assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Disconnect the H34 and H35 front No. 2 speaker assembly connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H95-1 (FR+) - H34-3 (TWR+) | Always | Below 1 Ω |
| H95-6 (FR-) - H34-1 (TWR-) | Always | Below 1 Ω |
| H95-2 (FL+) - H35-3 (TWL+) | Always | Below 1 Ω |
| H95-7 (FL-) - H35-1 (TWL-) | Always | Below 1 Ω |
| H34-4 (+) - J4-1 | Always | Below 1 Ω |
| H34-2 (-) - J4-2 | Always | Below 1 Ω |
| H35-4 (+) - K3-1 | Always | Below 1 Ω |
| H35-2 (-) - K3-2 | Always | Below 1 Ω |
| H95-1 (FR+) - Body ground | Always | 10 kΩ or higher |
| H95-6 (FR-) - Body ground | Always | 10 kΩ or higher |
| H95-2 (FL+) - Body ground | Always | 10 kΩ or higher |
| H95-7 (FL-) - Body ground | Always | 10 kΩ or higher |
| H34-4 (+) - Body ground | Always | 10 kΩ or higher |
| H34-2 (-) - Body ground | Always | 10 kΩ or higher |
| H35-4 (+) - Body ground | Always | 10 kΩ or higher |
| H35-2 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 2 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 2 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H95 radio and display receiver assembly connector.
Disconnect the L1 and M1 rear speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H95-4 (RR+) - L1-1 | Always | Below 1 Ω |
| H95-9 (RR-) - L1-2 | Always | Below 1 Ω |
| H95-3 (RL+) - M1-1 | Always | Below 1 Ω |
| H95-8 (RL-) - M1-2 | Always | Below 1 Ω |
| H95-4 (RR+) - Body ground | Always | 10 kΩ or higher |
| H95-9 (RR-) - Body ground | Always | 10 kΩ or higher |
| H95-3 (RL+) - Body ground | Always | 10 kΩ or higher |
| H95-8 (RL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>REMOVAL
Inspect the rear speaker set.
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>INSPECTION
Malfunction disappears.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>REMOVAL
Enter the "System Check Mode" screen. Refer to Check Speaker in Operation Check.
Perform the operation check above and determine the speaker that is not operating.
| Not Operating Speaker | Proceed to |
|---|---|
| Front No. 1 speaker assembly | A |
| Front No. 2 speaker assembly or front No. 3 speaker assembly | B |
| Front No. 4 speaker assembly | C |
| Rear speaker set | D |
If sound cannot be heard from any speaker, inspect all of them.
A
B
C
D
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the J4 and K3 front No. 1 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-5 (WFR+) - J4-1 | Always | Below 1 Ω |
| H67-20 (WFR-) - J4-2 | Always | Below 1 Ω |
| H67-4 (WFL+) - K3-1 | Always | Below 1 Ω |
| H67-19 (WFL-) - K3-2 | Always | Below 1 Ω |
| H67-5 (WFR+) - Body ground | Always | 10 kΩ or higher |
| H67-20 (WFR-) - Body ground | Always | 10 kΩ or higher |
| H67-4 (WFL+) - Body ground | Always | 10 kΩ or higher |
| H67-19 (WFL-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>REMOVAL
Inspect the front No. 1 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>FRONT DOOR SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*: w/ Telematics Transceiver
Disconnect the G187 telematics transceiver connector*.
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H10 and H13 front No. 2 speaker assembly connectors.
Disconnect the H21 and H22 front No. 3 speaker assembly connectors.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-12 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H67-27 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H67-13 (FR+) - G187-2 (SPI+) | Always | Below 1 Ω |
| H67-28 (FR-) - G187-3 (SPI-) | Always | Below 1 Ω |
| G187-5 (SPO+) - H21-1 (TWR+) | Always | Below 1 Ω |
| G187-6 (SPO-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H67-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| H67-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| H67-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| H67-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| G187-5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| G187-6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-12 (FL+) - H22-1 (TWL+) | Always | Below 1 Ω |
| H67-27 (FL-) - H22-2 (TWL-) | Always | Below 1 Ω |
| H67-13 (FR+) - H21-1 (TWR+) | Always | Below 1 Ω |
| H67-28 (FR-) - H21-2 (TWR-) | Always | Below 1 Ω |
| H21-3 (+) - H10-2 | Always | Below 1 Ω |
| H21-4 (-) - H10-1 | Always | Below 1 Ω |
| H22-3 (+) - H13-2 | Always | Below 1 Ω |
| H22-4 (-) - H13-1 | Always | Below 1 Ω |
| H67-12 (FL+) - Body ground | Always | 10 kΩ or higher |
| H67-27 (FL-) - Body ground | Always | 10 kΩ or higher |
| H67-13 (FR+) - Body ground | Always | 10 kΩ or higher |
| H67-28 (FR-) - Body ground | Always | 10 kΩ or higher |
| H21-3 (+) - Body ground | Always | 10 kΩ or higher |
| H21-4 (-) - Body ground | Always | 10 kΩ or higher |
| H22-3 (+) - Body ground | Always | 10 kΩ or higher |
| H22-4 (-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 2 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the front No. 3 speaker assembly with a new or known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>PILLAR SPEAKER>REMOVAL
Check the malfunction disappears.
Malfunction disappears.
Connect all the connectors to the front No. 3 speaker assemblies that were disconnected.
When there is a possibility that either the right or left front speaker is defective, inspect by interchanging the right one with the left one.
Perform the above inspection on both the LH and RH sides.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(DCM [Telematics Transceiver]) |
Remove the DCM (telematics transceiver).
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 (SPO+) - 2 (SPI+) | Always | Below 1 Ω |
| 6 (SPO-) - 3 (SPI-) | Always | Below 1 Ω |
| 5 (SPO+) - Body ground | Always | 10 kΩ or higher |
| 6 (SPO-) - Body ground | Always | 10 kΩ or higher |
| 2 (SPI+) - 3 (SPI-) | Always | 10 kΩ or higher |
| 5 (SPO+) - 6 (SPO-) | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the H14 front No. 4 speaker assembly connector.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-7 (CTR+) - H14-2 | Always | Below 1 Ω |
| H67-22 (CTR-) - H14-1 | Always | Below 1 Ω |
| H67-7 (CTR+) - Body ground | Always | 10 kΩ or higher |
| H67-22 (CTR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>REMOVAL
Inspect the front No. 4 speaker assembly.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>INSTRUMENT PANEL SPEAKER>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
*1: for 5 Door
*2: for 3 Door
Disconnect the H67 stereo component amplifier assembly connector.
Disconnect the L1 and M1 rear speaker set connectors*1.
Disconnect the Q32 and R37 rear speaker set connectors*2.
Measure the resistance according to the value (s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-8 (RL+) - M1-1 | Always | Below 1 Ω |
| H67-23 (RL-) - M1-2 | Always | Below 1 Ω |
| H67-9 (RR+) - L1-1 | Always | Below 1 Ω |
| H67-24 (RR-) - L1-2 | Always | Below 1 Ω |
| H67-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| H67-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| H67-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| H67-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H67-8 (RL+) - R37-1 | Always | Below 1 Ω |
| H67-23 (RL-) - R37-2 | Always | Below 1 Ω |
| H67-9 (RR+) - Q32-1 | Always | Below 1 Ω |
| H67-24 (RR-) - Q32-2 | Always | Below 1 Ω |
| H67-8 (RL+) - Body ground | Always | 10 kΩ or higher |
| H67-23 (RL-) - Body ground | Always | 10 kΩ or higher |
| H67-9 (RR+) - Body ground | Always | 10 kΩ or higher |
| H67-24 (RR-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the rear speaker set.
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>REMOVAL
Inspect the rear speaker set.
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>INSPECTION
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for 5 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>REAR DOOR SPEAKER>REMOVAL
for 3 Doors: Click hereAudio / Visual / Telematics>AUDIO / VIDEO>QUARTER TRIM SPEAKER (for 3 Door)>REMOVAL