Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1800  Short in D Squib Circuit  B1801  Open in D Squib Circuit  B1802  Short in D Squib Circuit (to Ground)  B1803  Short in D Squib Circuit (to +B)  


DESCRIPTION

The driver side squib circuit consists of the center airbag sensor, spiral cable and steering pad.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side squib circuit.


DTC Code DTC Detection Condition Trouble Area
B1800 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the driver side squib circuit during the primary check.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor


B1801 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the driver side squib circuit for 2 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor


B1802 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor


B1803 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the driver side squib circuit for 0.5 seconds.

·

A driver side squib malfunction.

·

A spiral cable malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Spiral cable sub-assembly

·

Steering pad (Driver side squib)

·

Center airbag sensor



WIRING DIAGRAM

U148201E01
2.124,1.582 2.349,1.738 0.225,0.156 10 D+ 2.159,2.422 2.335,2.578 0.177,0.156 10 D- 4.892,1.664 5.117,1.820 0.225,0.156 10 D+ 4.892,2.505 5.069,2.660 0.177,0.156 10 D- 3.232,1.57 3.457,1.761 0.225,0.191 10 1 3.232,2.418 3.408,2.609 0.177,0.191 10 2 2.475,2.995 2.826,3.158 0.350,0.163 10 G41 0.794,2.995 1.144,3.158 0.350,0.163 10 z5 2.475,3.15 3.284,3.320 0.809,0.170 10 Spiral Cable 0.78,3.17 1.950,3.340 1.170,0.170 10 Driver Side Squib 4.591,1.552 4.754,1.791 0.163,0.239 10 5 4.591,2.385 4.830,2.611 0.239,0.225 10 6 4.808,4.165 5.096,4.307 0.288,0.142 10 G1 4.808,4.327 6.186,4.497 1.378,0.170 10 Center Airbag Sensor 2.475,2.428 2.701,2.618 0.225,0.191 10 1 2.475,1.58 2.652,1.771 0.177,0.191 10 2

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK STEERING PAD (DRIVER SIDE SQUIB)
a.

Turn the ignition switch off.

C385394C02
5.875,2 5.521,1.573 false 6.01,1.521 5.719,1.219 false 0.771,0.896 0.771,0.635 false 0.771,2.396 0.771,2.135 false 0.271,0.104 0.583,0.26 0.313,0.156 10 false *A 1.219,0.927 1.531,1.083 0.313,0.156 10 false *2 2.385,1.25 2.698,1.406 0.313,0.156 10 false *3 6.042,0.781 6.354,0.938 0.313,0.156 10 false *4 6.052,1.5 6.365,1.656 0.313,0.156 10 false *5 5.313,0.281 5.625,0.438 0.313,0.156 10 false *a 5.927,2.021 6.24,2.188 0.313,0.167 10 false *b 0.292,1.438 0.604,1.594 0.313,0.156 10 false *B 4.417,1.052 4.729,1.25 0.313,0.198 10 false z5 0.698,0.927 1.01,1.083 0.313,0.156 10 false *1 2.521,0.479 2.75,0.677 0.229,0.198 10 false A 2.521,1.99 2.75,2.188 0.229,0.198 10 false A 0.833,0.729 0.99,0.938 0.156,0.208 10 false F 1.01,0.719 1.167,0.927 0.156,0.208 10 false E 1.958,0.708 2.115,0.917 0.156,0.208 10 false D 2.083,0.708 2.24,0.917 0.156,0.208 10 false C 0.844,2.24 1,2.448 0.156,0.208 10 false F 1.031,2.229 1.188,2.438 0.156,0.208 10 false E 1.958,2.208 2.115,2.417 0.156,0.208 10 false D 2.083,2.188 2.24,2.396 0.156,0.208 10 false C 0.719,2.406 1.031,2.563 0.313,0.156 10 false *1 1.229,2.417 1.542,2.573 0.313,0.156 10 false *2 2.406,2.49 2.719,2.646 0.313,0.156 10 false *3
*A w/o Side Airbag *B w/ Side Airbag
*1 Driver Side Squib *2 Spiral Cable
*3 Center Airbag Sensor *4 Connector E
*5 SST - -
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange



b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the steering pad.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).

CAUTION:

Never connect the tester to the steering pad (driver side squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector E.


d.
C385395C02
0.156,0.219 0.469,0.375 0.313,0.156 10 false *A 0.208,2.188 0.521,2.344 0.313,0.156 10 false *B 0.135,0.854 0.448,1.01 0.313,0.156 10 false *1 0.74,1.656 1.052,1.813 0.313,0.156 10 false *2 2.208,1.99 2.521,2.146 0.313,0.156 10 false *3 0.115,3.073 0.427,3.229 0.313,0.156 10 false *1 0.76,3.875 1.073,4.031 0.313,0.156 10 false *2 2.25,3.969 2.563,4.125 0.313,0.156 10 false *3 2.333,1.104 2.49,1.302 0.156,0.198 10 false A 2.344,3.375 2.5,3.573 0.156,0.198 10 false A 1.979,1.406 2.135,1.604 0.156,0.198 10 false B 1.635,1.406 1.792,1.604 0.156,0.198 10 false C 1.51,1.406 1.667,1.604 0.156,0.198 10 false D 0.51,1.396 0.667,1.594 0.156,0.198 10 false E 0.323,1.396 0.479,1.594 0.156,0.198 10 false F 0.302,3.615 0.458,3.813 0.156,0.198 10 false F 0.51,3.625 0.667,3.823 0.156,0.198 10 false E 1.51,3.604 1.667,3.802 0.156,0.198 10 false D 1.646,3.604 1.802,3.802 0.156,0.198 10 false C 1.99,3.615 2.146,3.813 0.156,0.198 10 false B
*A w/o Side Airbag
*B w/ Side Airbag
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor


Check that the spiral cable connectors (on the steering pad side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK DRIVER SIDE SQUIB CIRCUIT

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

3.CHECK DRIVER SIDE SQUIB CIRCUIT
a.

Disconnect the connectors from the center airbag sensor.

C385396C01
6.073,2.104 5.708,1.729 false 6.135,1.74 5.604,1.24 true 5.083,1.781 5.521,1.24 true 0.563,1.01 0.563,0.667 false 0.573,2.49 0.573,2.208 false 0.094,0.031 0.406,0.188 0.313,0.156 10 false *A 0.115,1.375 0.427,1.531 0.313,0.156 10 false *B 0.479,1.031 0.792,1.188 0.313,0.156 10 false *1 1.031,1.031 1.344,1.188 0.313,0.156 10 false *2 2.344,1.281 2.656,1.438 0.313,0.156 10 false *3 6.292,1.073 6.604,1.229 0.313,0.156 10 false *4 5.458,0.531 5.771,0.688 0.313,0.156 10 false *a 6.125,2.125 6.438,2.281 0.313,0.156 10 false *b 0.521,2.521 0.833,2.677 0.313,0.156 10 false *1 1.031,2.531 1.344,2.688 0.313,0.156 10 false *2 2.385,2.594 2.698,2.75 0.313,0.156 10 false *3 4.583,1.323 4.896,1.521 0.313,0.198 10 false z5 4.969,1.823 5.281,2.021 0.313,0.198 10 false D- 6.135,1.802 6.448,2 0.313,0.198 10 false D+ 2.51,0.521 2.667,0.719 0.156,0.198 10 false A 1.875,0.74 2.031,0.938 0.156,0.198 10 false C 1.76,0.74 1.917,0.938 0.156,0.198 10 false D 0.833,0.75 0.99,0.948 0.156,0.198 10 false E 0.646,0.76 0.802,0.958 0.156,0.198 10 false F 2.167,0.75 2.323,0.948 0.156,0.198 10 false B 0.656,2.292 0.813,2.49 0.156,0.198 10 false F 0.854,2.281 1.01,2.479 0.156,0.198 10 false E 1.76,2.281 1.917,2.479 0.156,0.198 10 false D 1.885,2.281 2.042,2.479 0.156,0.198 10 false C 2.188,2.292 2.344,2.49 0.156,0.198 10 false B 2.5,2.083 2.656,2.281 0.156,0.198 10 false A
*A w/o Side Airbag *B w Side Airbag
*1 Driver Side Squib *2 Spiral Cable
*3 Center Airbag Sensor *4 Connector E
*a Front view of wire harness connector
(to Driver Side Squib)
*b Color: Orange



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
z5-2 (D+) - Body ground Ignition switch ON Below 1 V
z5-1 (D-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z5-2 (D+) - z5-1 (D-) Always 1 MΩ or higher
z5-2 (D+) - Body ground Always 1 MΩ or higher
z5-1 (D-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
4.CHECK CENTER AIRBAG SENSOR
a.
C385397C01
0.083,0.115 0.396,0.271 0.313,0.156 10 false *A 0.208,2.281 0.521,2.438 0.313,0.156 10 false *B 0.24,1.198 0.552,1.354 0.313,0.156 10 false *1 0.75,1.573 1.063,1.729 0.313,0.156 10 false *2 2.125,1.917 2.438,2.073 0.313,0.156 10 false *3 0.26,3.635 0.573,3.792 0.313,0.156 10 false *1 0.75,4.021 1.063,4.177 0.313,0.156 10 false *2 2.167,4.063 2.479,4.219 0.313,0.156 10 false *3 0.406,1.292 0.563,1.49 0.156,0.198 10 false F 0.521,1.292 0.677,1.49 0.156,0.198 10 false E 1.604,1.281 1.76,1.479 0.156,0.198 10 false D 1.719,1.281 1.875,1.479 0.156,0.198 10 false C 0.438,3.698 0.594,3.896 0.156,0.198 10 false F 0.552,3.698 0.708,3.896 0.156,0.198 10 false E 1.604,3.708 1.76,3.906 0.156,0.198 10 false D 1.729,3.708 1.885,3.906 0.156,0.198 10 false C
*A w/o Side Airbag
*B w/ Side Airbag
*1 Driver Side Squib
*2 Spiral Cable
*3 Center Airbag Sensor


Connect the connectors to the steering pad and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1800, B1801, B1802 or B1803 is not output.


HINT:

Codes other than DTC B1800, B1801, B1802 and B1803 may be output at this time, but they are not related to this check.




OK

NG

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE)
a.

Restore the released activation prevention mechanism of connector B to its original condition.

C385398C01
5.208,1.938 5.833,1.458 true 6.521,1.896 5.948,1.458 true 0.104,0.083 0.417,0.24 0.313,0.156 10 false *A 0.135,1.271 0.448,1.427 0.313,0.156 10 false *B 2.052,0.25 2.365,0.406 0.313,0.156 10 false *1 1.135,0.906 1.448,1.063 0.313,0.156 10 false *2 2.375,1.188 2.688,1.344 0.313,0.156 10 false *3 6.417,1.01 6.729,1.167 0.313,0.156 10 false *4 5.688,0.75 6,0.906 0.313,0.156 10 false *a 4.771,1.344 5.229,1.542 0.458,0.198 10 false G41 1.146,2.406 1.458,2.563 0.313,0.156 10 false *2 2.073,1.76 2.385,1.917 0.313,0.156 10 false *1 2.417,2.479 2.729,2.635 0.313,0.156 10 false *3 2.5,0.479 2.656,0.677 0.156,0.198 10 false A 2.5,1.979 2.656,2.177 0.156,0.198 10 false A 0.969,0.729 1.125,0.927 0.156,0.198 10 false E 1.802,0.719 1.958,0.917 0.156,0.198 10 false D 1.948,2.198 2.104,2.396 0.156,0.198 10 false C 1.948,0.719 2.104,0.917 0.156,0.198 10 false C 2.177,0.729 2.333,0.927 0.156,0.198 10 false B 2.219,2.198 2.375,2.396 0.156,0.198 10 false B 1.781,2.208 1.938,2.406 0.156,0.198 10 false D 0.979,2.219 1.135,2.417 0.156,0.198 10 false E 0.771,0.74 0.927,0.938 0.156,0.198 10 false F 0.802,2.208 0.958,2.406 0.156,0.198 10 false F 5.073,1.948 5.385,2.104 0.313,0.156 10 false D- 6.5,1.969 6.813,2.125 0.313,0.156 10 false D+
*A w/o Side Airbag *B w/ Side Airbag
*1 Instrument Panel Wire *2 Spiral Cable
*3 Center Airbag Sensor *4 Connector C
*a Rear view of wire harness connector
(to Spiral Cable)
- -



b.

Disconnect the instrument panel wire connector from the spiral cable.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G41-1 (D+) - Body ground Ignition switch ON Below 1 V
G41-2 (D-) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-1 (D+) - G41-2 (D-) Always Below 1 Ω



h.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G41-1 (D+) - G41-2 (D-) Always 1 MΩ or higher
G41-1 (D+) - Body ground Always 1 MΩ or higher
G41-2 (D-) - Body ground Always 1 MΩ or higher




OK

REPLACE SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE INSTRUMENT PANEL WIRE