The driver side squib 2nd step circuit consists of the center airbag sensor, spiral cable and steering pad.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.
| DTC Code | DTC Detection Condition | Trouble Area |
|---|---|---|
| B1810 | One of the following conditions is met:
·
The center airbag sensor detects a line short circuit signal 5 times in the driver side squib 2nd step circuit during the primary check. ·
A driver side squib 2nd step malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib 2nd step) ·
Center airbag sensor |
| B1811 | One of the following conditions is met:
·
The center airbag sensor detects open circuit signal in the driver side squib 2nd step circuit for 2 seconds. ·
A driver side squib 2nd step malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib 2nd step) ·
Center airbag sensor |
| B1812 | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to ground signal in the driver side 2nd step circuit for 0.5 seconds. ·
A driver side squib 2nd step malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib 2nd step) ·
Center airbag sensor |
| B1813 | One of the following conditions is met:
·
The center airbag sensor detects a short circuit to B+ signal in the driver side squib 2nd step circuit for 0.5 seconds. ·
A driver side squib 2nd step malfunction. ·
A spiral cable malfunction. ·
A center airbag sensor malfunction. |
·
Instrument panel wire ·
Spiral cable sub-assembly ·
Steering pad (Driver side squib 2nd step) ·
Center airbag sensor |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
When installing the spiral cable and steering wheel, be sure to adjust the spiral cable as it may break if the steering wheel is turned before adjusting the spiral cable (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSTALLATION).
When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).
After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).
To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Turn the ignition switch off.
| *A | w/o Side Airbag | *B | w/ Side Airbag |
| *1 | Driver Side Squib 2nd Step | *2 | Spiral Cable |
| *3 | Center Airbag Sensor | *4 | Connector E |
| *5 | SST | - | - |
| *a | Front view of wire harness connector
(to Driver Side Squib 2nd Step) |
*b | Color: Black |
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Never connect the tester to the steering pad (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1810, B1811, B1812 or B1813 is not output.
Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
| *A | w/o Side Airbag |
| *B | w/ Side Airbag |
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
Check that the spiral cable connectors (on the steering pad side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
OK
NG
| *A | w/o Side Airbag | *B | w/ Side Airbag |
| *1 | Driver Side Squib 2nd Step | *2 | Spiral Cable |
| *3 | Center Airbag Sensor | *4 | Connector E |
| *a | Front view of wire harness connector
(to Driver Side Squib 2nd Step) |
*b | Color: Black |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| z6-2 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| z6-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-2 (D2+) - z6-1 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z6-2 (D2+) - z6-1 (D2-) | Always | 1 MΩ or higher |
| z6-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| z6-1 (D2-) - Body ground | Always | 1 MΩ or higher |
OK
NG
| *A | w/o Side Airbag |
| *B | w/ Side Airbag |
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
Connect the connectors to the steering pad and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).
DTC B1810, B1811, B1812 or B1813 is not output.
Codes other than DTC B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.
OK
NG
Restore the released activation prevention mechanism of connector B to its original condition.
| *A | w/o Side Airbag | *B | w/ Side Airbag |
| *1 | Instrument Panel Wire | *2 | Spiral Cable |
| *3 | Center Airbag Sensor | *4 | Connector C |
| *a | Rear view of wire harness connector
(to Spiral Cable) |
- | - |
Disconnect the instrument panel wire connector from the spiral cable.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G41-4 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| G41-3 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G41-4 (D2+) - G41-3 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G41-4 (D2+) - G41-3 (D2-) | Always | 1 MΩ or higher |
| G41-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| G41-3 (D2-) - Body ground | Always | 1 MΩ or higher |
OK
NG