Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P008800  Fuel Rail/System Pressure - Too High  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P008800 Fuel Rail/System Pressure - Too High The fuel pressure of the common rail exceeds 275000 kPa (2804 kgf/cm2, 39875 psi).
(1 trip detection logic)
·

Pre-stroke control valve (fuel supply pump assembly)

·

Pressure discharge valve (common rail assembly)

·

Open or short in pre-stroke control valve circuit

·

No. 1 injector assembly (fuel pressure sensor)

·

No. 4 injector assembly (fuel pressure sensor)

·

ECM


Comes on DTC stored SAE Code: P0088

Related Data List
DTC No. Data List
P008800
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)

·

Fuel Pressure #1

·

Fuel Pressure #4



HINT:
·

For more information on the common rail system, refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>SYSTEM DESCRIPTION).

·

When DTC P008800 is stored, check the internal fuel pressure of the common rail assembly by entering the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).

Reference
Engine Speed Fuel Pressure (High)
Idling Approximately 25000 to 50000 kPa
3000 rpm (No engine load) Approximately 36000 to 120000 kPa

·

Check "Fuel Pressure (High)" and "Target Fuel Pressure (High)" in the freeze frame data.



CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P008800 After idling for 60 seconds, quickly increase engine speed to 2500 rpm repeatedly for 30 seconds

MONITOR DESCRIPTION

The ECM stores this DTC if the fuel pressure inside the common rail assembly is higher than 275000 kPa (2804 kgf/cm2, 39875 psi). This DTC indicates that: 1) the pre-stroke control valve may be stuck open, or 2) there may be a short in the pre-stroke control valve circuit.

If this DTC is stored, the ECM enters fail-safe mode and limits the engine power. The ECM continues operating in fail-safe mode until the ignition switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P008800)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read Current DTCs.

Result:
Result Proceed to
P008800 is output A
P008800 and DTCs related to the fuel pressure sensor circuit* are output B


HINT:
·

*: Fuel pressure sensor circuit DTC: P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13E011, P13E015, P13E511, P13E515.

·

When there is an open circuit in the fuel pressure sensor circuit, the fuel pressure sensor outputs the maximum value. Therefore, P008800 may be stored together with DTCs which indicate common rail fuel pressure sensor circuit malfunctions.





A

2.CHECK FREEZE FRAME DATA (COMMON RAIL PRESSURE)

B

GO TO FUEL RAIL PRESSURE SENSOR CIRCUIT

2.CHECK FREEZE FRAME DATA (COMMON RAIL PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Record the stored DTCs and freeze frame data.

Result:
Result Proceed to
Value of Fuel Pressure (High) is shifting towards 160000 kPag or higher in 3rd and 4th set of freeze frame data B
Except above A




A

3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

B

5.REPLACE FUEL SUPPLY PUMP ASSEMBLY
3.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A460802C25
1.271,0.854 1.667,1.125 0.396,0.271 1.802,0.854 2.198,1.125 0.396,0.271 0.802,2.583 1.625,1.635 true 1.375,2.573 1.667,1.635 true 2.01,2.573 1.906,1.635 true 2.51,2.594 1.99,1.635 true 1.323,0.917 1.781,1.115 0.458,0.198 10 false C151 1.854,0.917 2.313,1.115 0.458,0.198 10 false C152 0.396,2.583 1.042,2.813 0.646,0.229 10 false 19 (EIJ1) 1.042,2.573 1.688,2.781 0.646,0.208 10 false 18 (PIJ1) 1.729,2.573 2.375,2.781 0.646,0.208 10 false 23 (PIJ4) 2.365,2.583 3.01,2.813 0.646,0.229 10 false 21 (EIJ4) 0.135,0.135 0.594,0.333 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the No. 1 or No. 4 injector assembly and ECM.

A192849E06
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.396 5.865,1.958 2.01,0.563 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.406,1.094 2.188,0.49 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.583,0.292 2.333,0.531 0.75,0.24 10 false Example: 4.375,2.583 6.417,2.813 2.042,0.229 10 false Tester Range (Reference): 4.375,2.844 6.771,3.156 2.396,0.313 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C151-18 (PIJ1) - C151-19 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C152-23 (PIJ4) - C152-21 (EIJ4)


Result:
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A




A

4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)

B

9.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE PRE-STROKE CONTROL VALVE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Activate the Pre-stroke Control Valve


d.

Perform the Active Test and check that operation sounds can be heard from the pre-stroke control valve.

HINT:
·

Perform this procedure with the engine stopped and check the operation sounds from outside the vehicle.

·

Check in a quiet location with the hood opened, as the operation sound is difficult to hear.

·

In order to distinguish between the operation sounds of other actuators, check by using the GTS to turn the Active Test open and close several times.



OK:

The operation sound is generated when performing the Active Test, and stops when finished.



Result:
Proceed to
OK
NG



NG

5.REPLACE FUEL SUPPLY PUMP ASSEMBLY

OK

8.REPLACE ECM
5.REPLACE FUEL SUPPLY PUMP ASSEMBLY
a.

Replace the fuel supply pump assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SUPPLY PUMP>REMOVAL


Result:
Proceed to
NEXT



NEXT

6.BLEED AIR FROM FUEL SYSTEM
6.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC OUTPUT
7.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P008800.


iii.

Check the DTC judgment result.

Result:
GTS Display Result Proceed to
Pending DTC P008800 is output A
All Readiness NORMAL B
ABNORMAL A


HINT:

If STATUS is INCOMPLETE, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.





A

8.REPLACE ECM

B

END

8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
10.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A460802C26
1.271,0.854 1.667,1.125 0.396,0.271 1.802,0.854 2.198,1.125 0.396,0.271 0.802,2.583 1.625,1.635 true 1.375,2.573 1.667,1.635 true 2.01,2.573 1.906,1.635 true 2.51,2.594 1.99,1.635 true 1.323,0.917 1.781,1.115 0.458,0.198 10 false C151 1.844,0.917 2.302,1.115 0.458,0.198 10 false C152 0.396,2.583 1.042,2.813 0.646,0.229 10 false 19 (EIJ1) 1.042,2.573 1.688,2.781 0.646,0.208 10 false 18 (PIJ1) 1.729,2.573 2.375,2.781 0.646,0.208 10 false 23 (PIJ4) 2.365,2.583 3.01,2.813 0.646,0.229 10 false 21 (EIJ4) 0.135,0.135 0.594,0.333 0.458,0.198 10 false *a
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM connector.


b.

Turn the ignition switch to ON.


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the No. 1 or No. 4 injector assembly and ECM.

A192849E06
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.396 5.865,1.958 2.01,0.563 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.406,1.094 2.188,0.49 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.583,0.292 2.333,0.531 0.75,0.24 10 false Example: 4.375,2.583 6.417,2.813 2.042,0.229 10 false Tester Range (Reference): 4.375,2.844 6.771,3.156 2.396,0.313 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C151-18 (PIJ1) - C151-19 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C152-23 (PIJ4) - C152-21 (EIJ4)


Result:
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B




A

11.REPLACE INJECTOR ASSEMBLY

B

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
11.REPLACE INJECTOR ASSEMBLY
a.

Replace the No. 1 or No. 4 injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly pipe, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
13.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the ignition switch to ON and start the engine.


e.

After idling for 60 seconds, increase the engine speed from idling to 2500 rpm repeatedly for 30 seconds.


f.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P008800.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, race the engine to 2500 rpm repeatedly for 30 seconds and increase the idling time.



Result:
Proceed to
NEXT



NEXT

END