Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P009300  Fuel System Leak Detected - Large Leak  P029D00  Cylinder 1 - Injector Leaking  P02A100  Cylinder 2 - Injector Leaking  P02A500  Cylinder 3 - Injector Leaking  P02A900  Cylinder 4 - Injector Leaking  


DESCRIPTION

A fuel pressure sensor, which is built into the injector assembly, converts the fuel pressure to an electrical signal which is sent to the ECM. Based on this signal, the ECM controls the fuel supply pump assembly and maintains the fuel pressure in the common rail assembly at the target pressure. Refer to System Description (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).

HINT:
·

If the drop in the internal fuel pressure is large when injecting fuel, the ECM interprets this as a fault and stores P009300, P029D00, P02A100, P02A500 and P02A900.

·

If P009300, P029D00, P02A100, P02A500 and P02A900 are present, refer to "Diagnostic Trouble Code (DTC) Table for Common Rail System" (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION).



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P009300 Fuel System Leak Detected - Large Leak While the engine is running, a large fuel pressure decrease occurs between injections (non-injection periods) or during a half-stroke of the engine.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on DTC stored SAE Code: P0093
P029D00 Cylinder 1 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on DTC stored SAE Code: P029D
P02A100 Cylinder 2 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on DTC stored SAE Code: P02A1
P02A500 Cylinder 3 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on DTC stored SAE Code: P02A5
P02A900 Cylinder 4 - Injector Leaking When the engine speed is at 650 rpm or more, the fuel pressure drop (slope of the line) is larger than the threshold and there is a time difference in the pressure drop of this cylinder compared to other cylinders for 1 second or more.
(1 trip detection logic)
·

Fuel line between fuel supply pump assembly and common rail assembly

·

Fuel line between common rail assembly and each injector assembly

·

Common rail assembly

·

Injector assembly

·

Pressure discharge valve (common rail assembly)

·

Fuel pressure sensor (built into injector assembly)

·

Crankshaft position sensor

·

Fuel filter element assembly

·

Open or short in injector assembly circuit

·

ECM


Comes on DTC stored SAE Code: P02A9

Related Data List
DTC No. Data List
P009300
P029D00
P02A100
P02A500
P02A900
·

Fuel Pressure (High)

·

Target Fuel Pressure (High)

·

i-ART Learning Status History #1 to #4

·

Injector Leaking Count #1 to #4



HINT:

When DTC P009300, P029D00, P02A100, P02A500 and P02A900 are set, check the internal fuel pressure of the common rail by entering the following menus on the GTS: Powertrain / Engine / Data List / Fuel Pressure (High).


Reference:
Engine Speed Fuel Pressure (High)
Idling Approximately 25000 to 50000 kPa
3000 rpm (No engine load) Approximately 36000 to 120000 kPa


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P009300
P029D00
P02A100
P02A500
P02A900
After idling for 60 seconds, run engine at 2500 rpm for 30 seconds.
Fully depress the accelerator pedal for 5 seconds, and then release it. [*A]
Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. [*B]
Repeat procedures [*A] and [*B] 5 times.

MONITOR DESCRIPTION

This DTC indicates that fuel leaks exist in high pressure areas in the common rail system. The ECM constantly monitors the internal fuel pressure of the common rail after the engine is started. The ECM stores this DTC if the drop in the internal fuel pressure is large when injecting fuel.

In the common rail system, high-pressure fuel is always supplied to the high-pressure areas including the fuel supply pump assembly, common rail assembly, injector assemblies and piping.

The ECM adjusts the timing of when the pre-stroke control valve is closed to obtain the target internal fuel pressure.

If this DTC is stored, the ECM enters fail-safe mode. In fail-safe mode, fuel supply pump assembly operation is limited. The ECM continues operating in fail-safe mode until the engine switch is turned off.

CAUTION / NOTICE / HINT

NOTICE:
·

Soon after starting the engine, visually check for fuel leaks in the fuel line.

·


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR FUEL LEAKS (IN HIGH-PRESSURE AREAS)
a.

Before starting the engine, visually check for fuel leaks from the fuel supply pump assembly, injector assembly, common rail assembly, and the fuel pipes in high-pressure areas.

OK:

No fuel leaks in high-pressure areas.



Result:
Proceed to
OK
NG



OK

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P009300) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)

NG

REPAIR FUEL LEAK POINT

2.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P009300) AND RECORD STORED DTC AND FREEZE FRAME DATA (PROCEDURE 2)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs and freeze frame data.

Result:
Result Proceed to
P009300 and "P13A011, P13A015, P13A02A, P13A511, P13A515, P13A52A, P13AA11, P13AA15, P13AA2A, P13B011, P13B015, P13B02A, P13E011, P13E015, P13E511 and/or P13E515" are output C
P009300 and "P033511, P033515, P03351F, P03352A and/or P033531" are output B
Except above A




A

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)

B

GO TO DTC CHART (CRANKSHAFT POSITION SENSOR CIRCUIT)

C

3.CHECK FUEL RECEIVER GAUGE (AMOUNT OF FUEL)
a.

Check if the fuel level is low.

Result:
Result Proceed to
The indicator (fuel warning light) is illuminated A
The indicator (fuel warning light) is not illuminated B




A

4.ADD FLUID

B

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #4)
4.ADD FLUID
a.

Add fuel.


Result:
Proceed to
NEXT



NEXT

5.CHECK WHETHER DTC OUTPUT RECURS
5.CHECK WHETHER DTC OUTPUT RECURS
a.
A360347

Using the hand pump mounted on the fuel filter cap, bleed the air from the fuel system. Continue pumping until the pump resistance increases.

NOTICE:
·

Hand pump pumping speed: Max. 2 strokes/sec.

·

The hand pump must be pushed with a full stroke during pumping.

·

When the fuel pressure at the supply pump inlet port reaches a saturated pressure, the hand pump resistance increases.

·

If pumping is interrupted during the air bleeding process, fuel in the fuel line may return to the fuel tank. Continue pumping until the hand pump resistance increases.

·

If the hand pump resistance does not increase despite consecutively pumping 200 times or more, there may be a fuel leak between the fuel tank and fuel filter element sub-assembly, the hand pump may be malfunctioning, or the vehicle may have run out of fuel.

·

If a large amount of air remains inside the fuel system, the common rail pressure does not rise to the pressure range necessary for normal use, and the engine cannot be started.




b.

Start the engine.

NOTICE:
·

If a large amount of air remains inside the fuel system, the starter may need to be cranked for 10 seconds or more to start the engine.

·

Do not crank the engine continuously for more than 20 seconds. The battery may be discharged.

·

Use a fully-charged battery.



i.

When the engine can be started, proceed to the next step.


ii.

If the engine cannot be started, bleed the air again using the hand pump until the hand pump resistance increases. Then start the engine.



c.

Turn the engine switch off.


d.

Connect the GTS to the DLC3.


e.

Turn the engine switch on (IG) and turn the GTS on.


f.

Clear the DTCs.


g.

Start the engine. [*A]


h.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak. [*B]


i.

Perform the following test 5 times with on/off intervals of 10 seconds: Active Test / Test the Fuel Leak. [*C]


j.

Allow the engine to idle for 3 minutes or more after performing the Active Test for the fifth time. [*D]

A192848E03
0.177,1.313 1.583,1.583 1.406,0.271 10 false Active Test Operation 6.5,2.313 6.896,2.49 0.396,0.177 10 false Time 1.677,0.969 2.042,1.167 0.365,0.198 10 false ON 1.646,1.625 2.073,1.823 0.427,0.198 10 false OFF 2.563,1.927 3.375,2.094 0.813,0.167 10 false 10 seconds 3.188,0.656 4,0.823 0.813,0.167 10 false 10 seconds 2.635,0.24 3.229,0.417 0.594,0.177 10 false 1st time 3.896,0.24 4.5,0.427 0.604,0.188 10 false 2nd time 5.198,0.24 5.792,0.406 0.594,0.167 10 false 5th time 5.99,1.865 6.75,2.083 0.76,0.219 10 false 3 minutes


k.

Enter the following menus: Powertrain / Engine / Trouble Codes.


l.

Read Current DTCs.

i.

When no DTCs are output, the air bleeding is completed.


ii.

If any DTCs are output, proceed to the next step.



m.

Repeat steps [*A] to [*D].


n.

Clear the DTCs.


o.

Start the engine and warm it up.


p.

Confirm that the shift lever is in neutral and securely apply the parking brake.


q.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*E]


r.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. [*F]


s.

Repeat procedures [*E] and [*F] 5 times.

A220593E68
1.656,1.844 2.042,2.021 0.385,0.177 10 false 5000 1.51,0.583 2.01,0.76 0.5,0.177 10 false 160000 5.135,2.125 5.771,2.302 0.635,0.177 10 false 3000 rpm 1.865,2.563 1.99,2.74 0.125,0.177 10 false 0 1.854,1.24 1.979,1.417 0.125,0.177 10 false 0 0.073,0.823 1.021,1.073 0.948,0.25 10 false Fuel Pressure 0.083,2.167 1.01,2.438 0.927,0.271 10 false Engine Speed 0.083,3.458 1.25,3.656 1.167,0.198 10 false Accelerator Pedal 0.948,3.083 2.115,3.281 1.167,0.198 10 false Fully Depressed 1.021,3.719 2,3.917 0.979,0.198 10 false Fully Released 2.875,4.24 3.573,4.427 0.698,0.188 10 false 5 seconds 6.448,4.135 6.854,4.323 0.406,0.188 10 false Time 3.104,2.958 3.729,3.198 0.625,0.24 10 false Step [*E] 6.208,2.948 6.813,3.188 0.604,0.24 10 false Step [*E] 4.75,2.958 5.375,3.198 0.625,0.24 10 false Step [*F] 2.104,0.573 2.375,0.76 0.271,0.188 10 false kPa 2.073,1.771 2.385,1.938 0.313,0.167 10 false rpm


t.

Enter the following menus: Powertrain / Engine / Trouble Codes.


u.

Read Current DTCs.

Result:
Result Proceed to
DTC is output A
No DTC is output B




A

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #4)

B

DTC CAUSED BY RUNNING OUT OF FUEL

6.CHECK FREEZE FRAME DATA (INJECTION FEEDBACK VALUE #1 TO #4)
a.

Read the value of Injection Feedback Value #1 to #4 in the freeze frame data recorded in Procedure 2.

Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is 5 mm3/st in at least 1 set of freeze frame data B
Except above A


HINT:

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.




A

7.READ VALUE USING GTS (FUEL PRESSURE (HIGH))

B

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
7.READ VALUE USING GTS (FUEL PRESSURE (HIGH))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).


e.

Start the engine.


f.

Read the value of Fuel Pressure (High) while cranking and idling the engine.

Result:
Result Proceed to
The engine cannot be started or the engine can be started but Fuel Pressure (High) is below 20000 kPa 2 seconds after the starter signal changes from OFF to ON B
Except above A




A

8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
8.READ VALUE USING GTS (INJECTION FEEDBACK VALUE #1 TO #4)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Start the engine and warm it up.


d.

Enter the following menus: Powertrain / Engine / Data List / Injection Feedback Value #1 to #4.


e.

Read the values.

Standard:
GTS Display Engine Condition* Normal Value
Injection Feedback Value #1
Injection Feedback Value #2
Injection Feedback Value #3
Injection Feedback Value #4
Idling -5.0 mm3/st to 5.0 mm3/st


HINT:

*: The A/C switch and all accessory switches should be off, the engine coolant temperature should be 75°C (167°F) or higher and the engine should be idled for 1 minute or more.


Result:
Result Proceed to
Injection Feedback Value for at least one cylinder is more than 5 mm3/st and engine vibration is abnormally large B
Except above A


HINT:
·

When there is a problem with the operation of an injector assembly due to foreign matter in the inside of the injector assembly, etc., the fuel injection volume decreases. As a result, the ECM gives instructions to increase the fuel injection volume, which causes Injection Feedback Value to increase.

·

The ECM controls the system so that the sum of Injection Feedback Value for all of the cylinders is approximately 0 mm3/st. Even if the value of Injection Feedback Value for a cylinder is less than -5.0 mm3/st (-5.0 mm3/st is the lowest normal value), as long as the value of Injection Feedback Value for each of the other cylinders is 5.0 mm3/st or less, the injector assemblies are not malfunctioning.





A

9.CHECK ENGINE SPEED

B

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
9.CHECK ENGINE SPEED
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

While checking the tachometer, fully depress the accelerator pedal for 5 seconds, and then release it.*1


d.

Repeat procedure *1 5 times.

Result:
Result Proceed to
No problems such as sluggishness or variations in the tachometer reading A
Except above B




A

10.CHECK FREEZE FRAME DATA

B

18.READ VALUE USING GTS (ENGINE SPEED)
10.CHECK FREEZE FRAME DATA
a.

Read the value of Injector Leaking Count #1 to #4, and i-ART Learning Status History #1 to #4 in the freeze frame data recorded in Procedure 2.

Result:

If Injector Leaking Count #1 to #4 displays a value of 1 or higher, or i-ART Learning Status History #1 to #4 displays 1 Trip or more, the injector assembly for that cylinder needs to be replaced.


NOTICE:

In order to prevent foreign matter from entering the fuel lines, do not replace the injectors at this time. Replace the injectors after performing step 16.



Result:
Proceed to
NEXT



NEXT

11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
11.CLEAN FUEL FILTER CASE AND REPLACE FUEL FILTER ELEMENT
a.

Clean the fuel filter case and replace the fuel filter element assembly.

HINT:

Be sure to clean the inside of the fuel filter case as the injector assemblies may not operate properly if the fuel filter element assembly is installed with foreign matter remaining inside the fuel filter case.



Result:
Proceed to
NEXT



NEXT

12.BLEED AIR FROM FUEL SYSTEM
12.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
13.PERFORM ACTIVE TEST USING GTS (TEST THE FUEL LEAK)
a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Test the Fuel Leak / Data List / Fuel Pressure (High) and Target Fuel Pressure (High).


d.

Take a snapshot with the GTS during the Active Test.


e.

Measure the difference between the target fuel pressure (Target Fuel Pressure (High)) and the actual fuel pressure (Fuel Pressure (High)) when the "Test the Fuel Leak" Active Test is performed.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>DATA LIST / ACTIVE TEST

HINT:

In order to obtain an exact measurement, perform the Active Test 5 times and measure the difference once each time the Active Test is performed.


A227749E67
3.604,2.427 3.719,1.948 3.719,1.948 3.792,1.948 false 4.604,2.583 4.948,2.323 4.948,2.323 5.031,2.323 false 3.438,2.635 3.479,1.833 3.479,1.833 3.427,1.833 false 3.583,3.25 3.833,4.323 3.833,4.323 3.979,4.323 false 0.083,1.417 1.448,1.573 1.365,0.156 10 false Active Test Operation 0.083,0.583 1.479,0.781 1.396,0.198 10 false Engine Speed (rpm) 0.313,3.198 1.854,3.469 1.542,0.271 10 false Fuel Pressure (High) 3.802,1.865 5.74,2.031 1.938,0.167 10 false Target Fuel Pressure (High) 6.469,4.125 6.865,4.302 0.396,0.177 10 false Time 2.125,2.406 2.875,3.094 0.75,0.688 10 false Less than 10000 kPa 3,4.26 3.688,4.427 0.688,0.167 10 false 2 seconds 5.073,2.208 6.583,2.719 1.51,0.51 10 false Abnormal Fuel Pressure (High) 2.677,1.042 3.354,1.24 0.677,0.198 10 false Test Start 4.458,1.042 5.125,1.24 0.667,0.198 10 false Test Stop 5.885,1.042 6.563,1.24 0.677,0.198 10 false Test Start 2.073,1.76 3.427,2.188 1.354,0.427 10 false Normal Fuel Pressure (High) 1.646,0.271 2.021,0.438 0.375,0.167 10 false 2000 1.885,0.833 2.052,1 0.167,0.167 10 false 0 1.75,1.302 2.073,1.469 0.323,0.167 10 false ON 1.698,1.552 2.021,1.719 0.323,0.167 10 false OFF 4.021,4.25 5.948,4.708 1.927,0.458 10 false Pressure Discharge Valve Abnormal Fuel Pressure (High)

Standard:

The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa.


HINT:
·

"Target Fuel Pressure (High)" is the target fuel pressure controlled by the ECM.

·

"Fuel Pressure (High)" is the actual fuel pressure.



Result:
Result Proceed to
The difference between the target fuel pressure and the actual fuel pressure 2 seconds after the Active Test starts is less than 10000 kPa A
Except above B




A

14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)

B

15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
14.PERFORM ACTIVE TEST USING GTS (CONTROL THE SELECT CYLINDER FUEL CUT)
HINT:

Use this Active Test to determine the malfunctioning cylinder.


a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Active Test / Control the Select Cylinder Fuel Cut.

HINT:
·

If the engine idle speed does not change when an injector assembly is disabled, the cylinder being tested is malfunctioning. Record any malfunctioning cylinders.

·

If the cylinder being tested is normal, there will be a significant change in idle speed when the fuel injection is stopped for that cylinder.




Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
15.INSPECT INJECTOR ASSEMBLY (INSPECTION FOR VALVE CLOSING PROBLEM)
a.

Remove the glow plug for all the cylinders.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>GLOW PLUG>REMOVAL


b.

Visually check if there is fuel on the glow plugs.

HINT:
·

If there is fuel on a glow plug, fuel may be leaking from an injector assembly.

·

After replacing an injector assembly, make sure that the common rail pressure (fuel pressure) is within 5000 kPag (51.0 kgf/cm2, 725 psi) of the target fuel pressure while cranking the engine.

·

If there is fuel on a glow plug, fuel may have mixed with the engine oil. Check the engine oil amount and whether the engine oil smells of diesel fuel. If the oil level is above the full line or the engine oil smells of diesel fuel, replace the engine oil.





Result:
Proceed to
NEXT



NEXT

16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
16.REPLACE INJECTOR ASSEMBLY OF MALFUNCTIONING CYLINDER
NOTICE:
·

Replace the injector assembly of the cylinder which displays a value of 5.0 mm3/st or higher for Injection Feedback Value #1 to #4 in step 8.

·

Replace the injector assembly determined to be the problem in step 10 and any other injector assemblies which were determined to be malfunctioning in the steps up until this point.



a.

Replace the injector assembly of the malfunctioning cylinder.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL INJECTOR>REMOVAL

NOTICE:
·

When replacing the injector assembly for a cylinder, always be sure to use a new No. 1 injection pipe sub-assembly and a new No. 2 injection pipe sub-assembly.

·

Follow the procedure in the repair manual and temporarily install the No. 1 injection pipe sub-assembly, No. 2 injection pipe sub-assembly and No. 1 nozzle leakage pipe assembly, and then correctly position the injector assemblies. After that, tighten parts according to the torque specifications.

·

If the installation procedure is not performed correctly, injector assemblies may become out of position, which may cause the injector assemblies to deteriorate, resulting in malfunctions.

·

If an injector assembly deteriorates and malfunctions, other problems such as knocking, rough idle, etc. may occur.

·

If an injector assembly becomes out of position, it is possible that the seal between the injector assembly and injection pipe sub-assembly may become incomplete, resulting in a fuel leak.




Result:
Proceed to
NEXT



NEXT

17.BLEED AIR FROM FUEL SYSTEM
17.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
18.READ VALUE USING GTS (ENGINE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Engine Speed.


d.

Read the value while cranking and idling the engine.

Standard:
GTS Display Engine Condition Specified Condition
Engine Speed Cranking 50 to 400 rpm
Idling with warm engine
(L4 detection switch not in L4)
610 to 750 rpm


HINT:

The value should be the same as the actual engine speed and displayed with no interruption on the GTS.



Result:
Proceed to
OK
NG



OK

19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)

NG

26.REPLACE CRANKSHAFT POSITION SENSOR
19.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A460802C27
1.813,0.521 2.208,0.792 0.396,0.271 1.26,0.521 1.656,0.792 0.396,0.271 0.573,2.583 1.615,1.635 true 1.917,1.635 2.604,0.438 2.604,0.438 2.708,0.438 true 2.313,2.583 1.906,1.688 true 2.74,2.594 1.958,1.698 true 1.781,1.635 1.646,3.083 1.646,3.083 1.51,3.083 true 1.823,1.688 2.01,3.083 2.01,3.083 2.156,3.083 true 1.99,1.625 2.5,0.938 2.5,0.938 2.604,0.938 true 1.188,2.583 1.656,1.635 true 1.313,0.573 1.771,0.771 0.458,0.198 10 false C151 1.865,0.573 2.323,0.771 0.458,0.198 10 false C152 0.333,2.594 0.979,2.823 0.646,0.229 10 false 19 (EIJ1) 0.99,2.604 1.635,2.813 0.646,0.208 10 false 18 (PIJ1) 2.115,2.594 2.76,2.802 0.646,0.208 10 false 30 (EIJ2) 2.729,2.594 3.375,2.823 0.646,0.229 10 false 29 (PIJ2) 2.208,3 2.854,3.229 0.646,0.229 10 false 32 (EIJ3) 2.75,0.375 3.396,0.583 0.646,0.208 10 false 23 (PIJ4) 0.938,2.99 1.583,3.198 0.646,0.208 10 false 26 (PIJ3) 2.646,0.865 3.292,1.094 0.646,0.229 10 false 21 (EIJ4) 0.135,0.146 0.781,0.375 0.646,0.229 10 false *a
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the injector assembly and ECM.

A192849E07
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.417 5.854,1.969 2,0.552 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.396,1.125 2.177,0.521 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.573,0.281 2.302,0.604 0.729,0.323 10 false Example: 4.385,2.615 6.656,2.844 2.271,0.229 10 false Tester Range (Reference): 4.385,2.885 6.781,3.188 2.396,0.302 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C151-18 (PIJ1) - C151-19 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C152-29 (PIJ2) - C152-30 (EIJ2)
C152-26 (PIJ3) - C152-32 (EIJ3)
C152-23 (PIJ4) - C152-21 (EIJ4)



Result:
Result Proceed to
MIL comes on or noise present in the waveform B
Except above A



A

20.CHECK FOR INTERMITTENT PROBLEMS

B

22.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INJECTOR ASSEMBLY)
20.CHECK FOR INTERMITTENT PROBLEMS

Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
21.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn theengine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Clear the DTCs.


e.

Start the engine.


f.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


g.

Confirm that the shift lever is in neutral and securely apply the parking brake.


h.

Fully depress the accelerator pedal for 5 seconds, and then release it. [*A]


i.

Rev the engine to 3000 rpm and fully release the accelerator pedal immediately after the engine reaches 3000 rpm. [*B]


j.

Repeat procedures [*A] and [*B] 5 times.

A220593E69
1.635,1.854 2.021,2.125 0.385,0.271 10 false 5000 1.469,0.583 1.958,0.854 0.49,0.271 10 false 160000 5.135,2.115 5.781,2.417 0.646,0.302 10 false 3000 rpm 1.865,2.542 1.99,2.719 0.125,0.177 10 false 0 1.854,1.208 1.979,1.385 0.125,0.177 10 false 0 0.073,0.823 1,1.094 0.927,0.271 10 false Fuel Pressure 0.104,2.156 1.146,2.458 1.042,0.302 10 false Engine Speed 0.073,3.448 1.24,3.688 1.167,0.24 10 false Accelerator Pedal 0.948,3.083 2.031,3.313 1.083,0.229 10 false Fully Depressed 1.021,3.719 1.969,3.979 0.948,0.26 10 false Fully Released 2.917,4.219 3.667,4.458 0.75,0.24 10 false 5 seconds 6.448,4.125 6.854,4.313 0.406,0.188 10 false Time 3.104,2.958 3.865,3.198 0.76,0.24 10 false Step [*A] 6.208,2.958 6.813,3.198 0.604,0.24 10 false Step [*A] 4.75,2.958 5.458,3.188 0.708,0.229 10 false Step [*B] 2.104,0.573 2.49,0.844 0.385,0.271 10 false kPa 2.073,1.76 2.417,2.01 0.344,0.25 10 false rpm


k.

Enter the following menus: Powertrain / Engine / Trouble Codes


l.

Read the DTCs.

OK:

No DTCs are output.



Result:
Proceed to
NEXT



NEXT

END

22.REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - INJECTOR ASSEMBLY)
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

23.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
23.INSPECT ECM (FUEL PRESSURE SENSOR OUTPUT VOLTAGE)
a.
A460802C27
1.813,0.521 2.208,0.792 0.396,0.271 1.26,0.521 1.656,0.792 0.396,0.271 0.573,2.583 1.615,1.635 true 1.917,1.635 2.604,0.438 2.604,0.438 2.708,0.438 true 2.313,2.583 1.906,1.688 true 2.74,2.594 1.958,1.698 true 1.781,1.635 1.646,3.083 1.646,3.083 1.51,3.083 true 1.823,1.688 2.01,3.083 2.01,3.083 2.156,3.083 true 1.99,1.625 2.5,0.938 2.5,0.938 2.604,0.938 true 1.188,2.583 1.656,1.635 true 1.313,0.573 1.771,0.771 0.458,0.198 10 false C151 1.865,0.573 2.323,0.771 0.458,0.198 10 false C152 0.333,2.594 0.979,2.823 0.646,0.229 10 false 19 (EIJ1) 0.99,2.604 1.635,2.813 0.646,0.208 10 false 18 (PIJ1) 2.115,2.594 2.76,2.802 0.646,0.208 10 false 30 (EIJ2) 2.729,2.594 3.375,2.823 0.646,0.229 10 false 29 (PIJ2) 2.208,3 2.854,3.229 0.646,0.229 10 false 32 (EIJ3) 2.75,0.375 3.396,0.583 0.646,0.208 10 false 23 (PIJ4) 0.938,2.99 1.583,3.198 0.646,0.208 10 false 26 (PIJ3) 2.646,0.865 3.292,1.094 0.646,0.229 10 false 21 (EIJ4) 0.135,0.146 0.781,0.375 0.646,0.229 10 false *a
*a Component with harness connected
(ECM)


Connect the positive (+) probe of an oscilloscope to the PIJ terminal of the ECM connector and the negative (-) probe to the EIJ terminal of the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check for any noise in the waveform when vibration is applied to the wire harness and connectors between the injector assembly and ECM.

A192849E07
2.115,1.875 3.073,0.688 3.073,0.688 3.167,0.688 false 3.104,1.875 3.74,1.51 3.74,1.51 3.823,1.51 false 3.854,1.417 5.854,1.969 2,0.552 10 false Sensor Output Signal with Noise (Problem with Wire Connection) 3.219,0.604 5.396,1.125 2.177,0.521 10 false Sensor Output Signal without Noise (Normal Wire Connection) 1.573,0.281 2.302,0.604 0.729,0.323 10 false Example: 4.385,2.615 6.656,2.844 2.271,0.229 10 false Tester Range (Reference): 4.385,2.885 6.781,3.188 2.396,0.302 10 false 200 mV/DIV., 500 μsec./DIV. or less

Standard Voltage:
Tester Connection Condition Specified Condition
C151-18 (PIJ1) - C151-19 (EIJ1) Vibration is applied to the wire harness and connectors No noise in the waveform
C152-29 (PIJ2) - C152-30 (EIJ2)
C152-26 (PIJ3) - C152-32 (EIJ3)
C152-23 (PIJ4) - C152-21 (EIJ4)



Result:
Result Proceed to
MIL comes on or noise present in the waveform A
Except above B



A

24.REPLACE COMMON RAIL ASSEMBLY

B

21.CHECK WHETHER DTC OUTPUT RECURS
24.REPLACE COMMON RAIL ASSEMBLY
a.

Replace the common rail assembly.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>COMMON RAIL>REMOVAL

HINT:

Before replacing the common rail assembly, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

25.BLEED AIR FROM FUEL SYSTEM
25.BLEED AIR FROM FUEL SYSTEM
a.

Bleed the air from the fuel system.

Click hereEngine / Hybrid System>1GD-FTV (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION


Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS
26.REPLACE CRANKSHAFT POSITION SENSOR
a.

Replace the crankshaft position sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL

HINT:

Before replacing the crankshaft position sensor, perform a wire harness inspection and if there are any problems with the wire harness, repair or replace it.



Result:
Proceed to
NEXT



NEXT

21.CHECK WHETHER DTC OUTPUT RECURS