Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1500  Fuel Sender Open Detected  


DESCRIPTION

This DTC is stored when the combination meter assembly detects a fuel sender gauge assembly malfunction via a direct line.

DTC Code DTC Detection Condition Trouble Area
B1500 Both conditions are met:
·

The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.

·

Average input signal of fuel sender gauge is 630 Ω or more 3 times consecutively.


·

Harness or connector

·

Combination meter assembly

·

Fuel suction with pump and gauge tube assembly

·

Fuel tank vent tube assembly

·

Fuel sender gauge assembly



WIRING DIAGRAM

except 5L-E (for 5Door):
E380648E09
0.615,2.896 2.531,3.177 1.917,0.281 10 false Fuel Sender Gauge Assembly 0.521,3.542 3.052,3.729 2.531,0.188 10 false Fuel Suction Plate Sub-assembly 3.896,4.021 5.813,4.302 1.917,0.281 10 false Combination Meter Assembly 3.896,3.833 5.813,4.115 1.917,0.281 10 false G304 0.521,3.365 3.052,3.552 2.531,0.188 10 false S5 0.615,2.698 1.063,3.01 0.448,0.313 10 false A 2.333,1.927 2.646,2.156 0.313,0.229 10 false FR 2.313,2.427 2.656,2.667 0.344,0.24 10 false FE 2.313,1.448 2.771,1.656 0.458,0.208 10 false FV 3.958,1.469 4.313,1.719 0.354,0.25 10 false FV 3.948,1.917 4.292,2.156 0.344,0.24 10 false FR 3.938,2.417 4.469,2.667 0.531,0.25 10 false FE&B 3.708,1.469 4.167,1.677 0.458,0.208 10 false 24 3.719,1.896 4.177,2.104 0.458,0.208 10 false 27 3.771,2.427 4.229,2.635 0.458,0.208 10 false 3 2.625,1.448 3.083,1.656 0.458,0.208 10 false 1 2.625,1.896 3.083,2.104 0.458,0.208 10 false 3 2.625,2.406 3.083,2.615 0.458,0.208 10 false 2 1.823,1.573 2.281,1.781 0.458,0.208 10 false 1 1.833,2.01 2.292,2.219 0.458,0.208 10 false 3 1.813,2.5 2.271,2.708 0.458,0.208 10 false 2

except 5L-E (for 3Door):
B598639E01
0.594,3.052 2.51,3.333 1.917,0.281 10 false Fuel Sender Gauge Assembly 3.896,4.021 5.813,4.302 1.917,0.281 10 false Combination Meter Assembly 3.896,3.833 5.813,4.115 1.917,0.281 10 false G304 0.583,2.875 1.031,3.188 0.448,0.313 10 false R51 3.958,1.469 4.313,1.719 0.354,0.25 10 false FV 3.948,1.917 4.292,2.156 0.344,0.24 10 false FR 3.938,2.417 4.469,2.667 0.531,0.25 10 false FE&B 3.708,1.469 4.167,1.677 0.458,0.208 10 false 24 3.719,1.896 4.177,2.104 0.458,0.208 10 false 27 3.771,2.427 4.229,2.635 0.458,0.208 10 false 3 2.063,1.469 2.521,1.677 0.458,0.208 10 false 1 2.073,1.927 2.531,2.135 0.458,0.208 10 false 3 2.063,2.417 2.521,2.625 0.458,0.208 10 false 2 1.719,1.552 2.177,1.76 0.458,0.208 10 false FV 1.729,2.031 2.188,2.24 0.458,0.208 10 false FR 1.74,2.521 2.198,2.729 0.458,0.208 10 false FE

for 5L-E:
E321084E15
5.177,0.781 5.385,1.042 0.208,0.26 10 false L 5.177,1.406 5.458,1.677 0.281,0.271 10 false E 5.021,3.906 5.344,4.125 0.323,0.219 10 false G6 5.177,3.25 5.49,3.479 0.313,0.229 10 false E2 4.906,3.24 5.156,3.49 0.25,0.25 10 false 21 4.979,0.823 5.188,1.083 0.208,0.26 10 false 9 4.906,1.396 5.135,1.677 0.229,0.281 10 false 24 3.5,0.813 3.677,1.073 0.177,0.26 10 false 2 3.5,1.406 3.708,1.667 0.208,0.26 10 false 3 5.031,4.094 6.875,4.333 1.844,0.24 10 false Combination Meter Assembly 2.771,1.396 2.938,1.646 0.167,0.25 10 false 3 1.635,1.417 1.906,1.74 0.271,0.323 10 false 2 1.01,2.417 1.323,2.646 0.313,0.229 10 false S5 1,2.615 3.167,2.844 2.167,0.229 10 false Fuel Tank Vent Tube Assembly 1.365,1.813 3.396,2.125 2.031,0.313 10 false Fuel Sender Gauge Assembly 3.208,1.406 3.531,1.635 0.323,0.229 10 false FE 3.208,0.813 3.542,1 0.333,0.188 10 false FS 1.365,1.646 1.635,1.969 0.271,0.323 10 false A

CAUTION / NOTICE / HINT

NOTICE:

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.


PROCEDURE

1.READ VALUE USING GTS (FUEL INPUT)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Data List.


e.

Read the Data List according to the display on the GTS.

Combination Meter
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Fuel Input Fuel input/Min.: 0, Max.: 127.5 Current fuel level displayed Unit: L


Result:
Result Proceed to
Fuel level data can be displayed on the GTS A
Fuel level data cannot be displayed on the GTS B



A

REPLACE COMBINATION METER ASSEMBLY

B

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
except 5L-E (for 5Door) A
except 5L-E (for 3Door) B
for 5L-E C



A

3.INSPECT FUEL SENDER GAUGE ASSEMBLY

B

6.INSPECT FUEL SENDER GAUGE ASSEMBLY

C

8.INSPECT FUEL SENDER GAGE ASSEMBLY
3.INSPECT FUEL SENDER GAUGE ASSEMBLY


Result:
Proceed to
OK
NG



OK

4.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY

NG

4.INSPECT FUEL SUCTION PLATE SUB-ASSEMBLY
B598640C05
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.313 1.958,0.563 0.5,0.25 2.083,1.271 2.542,1.948 2.542,1.948 2.74,1.948 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 1.354,1.26 1.021,0.927 1.021,0.927 0.771,0.927 true 0.115,0.177 1.552,0.344 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 0.49,0.854 0.823,1.104 0.333,0.25 10 false FR 2.583,0.781 2.917,1.031 0.333,0.25 10 false FE 2.875,1.865 3.208,2.115 0.333,0.25 10 false FV 1.594,0.344 2.031,0.573 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Suction Plate Sub-assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-1 (FV) - A-1 Always Below 1 Ω
S5-2 (FE) - A-2 Always Below 1 Ω
S5-3 (FR) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

5.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the S5 fuel suction plate sub-assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (for 5Door):
Tester Connection Condition Specified Condition
S5-3 (FR) - G304-27 (FR) Always Below 1 Ω
S5-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
S5-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT FUEL SENDER GAUGE ASSEMBLY

OK

7.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (FUEL SUCTION PLATE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Disconnect the R51 fuel suction plate sub-assembly connector.


b.

Disconnect the G304 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R51-3 (FR) - G304-27 (FR) Always Below 1 Ω
R51-2 (FE) - G304-3 (FE&B) Always Below 1 Ω
R51-1 (FV) - G304-24 (FV) Always Below 1 Ω
G304-27 (FR) - Body ground Always 10 kΩ or higher
G304-3 (FE&B) - Body ground Always 10 kΩ or higher
G304-24 (FV) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT FUEL SENDER GAGE ASSEMBLY
a.

Remove the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>REMOVAL


b.

Inspect the fuel sender gauge assembly.

Click hereEngine / Hybrid System>5L-E (FUEL)>FUEL SENDER GAUGE ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

9.INSPECT FUEL TANK VENT TUBE ASSEMBLY

NG

REPLACE FUEL SENDER GAUGE ASSEMBLY

9.INSPECT FUEL TANK VENT TUBE ASSEMBLY
B599354C01
0.333,3.667 0.75,3.917 0.417,0.25 1.458,0.229 1.958,0.479 0.5,0.25 1.417,1.323 0.958,1.823 0.958,1.823 0.698,1.823 true 1.729,1.219 2.281,0.844 2.281,0.844 2.479,0.844 true 0.125,0.188 1.563,0.354 1.438,0.167 10 false *a 0.51,3.729 0.844,3.979 0.333,0.25 10 false A 2.583,0.781 2.917,1.031 0.333,0.25 10 false FS 0.469,1.76 0.802,2.01 0.333,0.25 10 false FE 1.625,0.281 2.063,0.51 0.438,0.229 10 false S5
*a Component without harness connected
(Fuel Tank Vent Tube Assembly)


a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
S5-2 (FS) - A-2 Always Below 1 Ω
S5-3 (FE) - A-3 Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

10.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)

NG

REPLACE FUEL TANK VENT TUBE ASSEMBLY

10.CHECK HARNESS AND CONNECTOR (FUEL GAUGE CIRCUIT)
a.

Disconnect the G6 combination meter assembly connector.


b.

Disconnect the S5 fuel sender gauge assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-9 (L) - S5-2 (FS) Always Below 1 Ω
G6-24 (E) - S5-3 (FE) Always Below 1 Ω
G6-21 (E2) - Body ground Always Below 1 Ω
G6-9 (L) or S5-2 (FS) - Body ground Always 10 kΩ or higher
G6-21 (E) or S5-3 (FE) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR