Home › Steering › STEERING GEAR / LINKAGE › STEERING GEAR › from 2020.08
RM27T0E _55 Steering _053719 STEERING GEAR / LINKAGE _0260966 STEERING GEAR A

STEERING GEAR / LINKAGE  STEERING GEAR  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 1.PLACE FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.REMOVE FRONT WHEELS

Hide 3.REMOVE ENGINE ASSEMBLY

Hide 45203 4.DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT

a.

for Manual Tilt and Manual Telescopic Steering Column:

Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Manual Tilt and Manual Telescopic Steering Column)>REMOVAL).


b.

for Power Tilt and Power Telescopic Steering Column:

Disconnect the No. 2 steering intermediate shaft (See page Steering>STEERING COLUMN>STEERING COLUMN ASSEMBLY (for Power Tilt and Power Telescopic Steering Column)>REMOVAL).


Hide 45047 5.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.
C215754E01
2.154,1.938 2.617,2.759 2.617,2.759 2.8,2.759 false 2.846,2.682 3.248,2.83 0.402,0.148 10 SST

Using SST, disconnect the tie rod end assembly.

SST
09610-20012  


Hide 45046 6.DISCONNECT TIE ROD END SUB-ASSEMBLY RH

HINT:

Use the same procedures described for the LH side.


Hide 44410 7.DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for LHD)

a.
C215750

Remove the clamp and disconnect the pressure feed tube (return tube side) from the steering gear.


b.
C215751

Using a union nut wrench, disconnect the pressure feed tube (pressure feed tube side) from the steering gear.


c.

Remove the bolt and disconnect the pressure feed tube clamp.

C449320C01
3.833,0.917 4.083,1.125 0.25,0.208 10 true *B 0.042,0.917 0.292,1.125 0.25,0.208 10 true *A 0.052,3.917 0.302,4.125 0.25,0.208 10 true *C 3.802,3.917 4.052,4.125 0.25,0.208 10 true *D

Text in Illustration
*A for 1GR-FE: *B for 2TR-FE:
*C for 5L-E: *D for 1GD-FTV:


Hide 44410 8.DISCONNECT PRESSURE FEED TUBE ASSEMBLY (for RHD)

a.
C218256

Remove the clamp and disconnect the pressure feed tube (return tube side) from the steering gear.


b.
C218257

Using a union nut wrench, disconnect the pressure feed tube (pressure feed tube side) from the steering gear.


c.

Remove the bolt and disconnect the pressure feed tube clamp.

C449321C01
0.25,1.25 0.469,1.448 0.219,0.198 10 true *A 3.833,1.25 4.052,1.448 0.219,0.198 10 true *B 0.281,4.333 0.5,4.531 0.219,0.198 10 true *C 3.833,4.302 4.052,4.5 0.219,0.198 10 true *D

Text in Illustration
*A for 1GR-FE: *B for 2TR-FE:
*C for 5L-E: *D for 1GD-FTV:


Hide 44250 9.REMOVE RACK AND PINION POWER STEERING GEAR ASSEMBLY

a.
C215749

Remove the 2 bolts, 2 nuts and steering gear assembly.

NOTICE:

Because the nut has its own stopper, do not turn the nut. Tighten the bolt with the nut fixed in place.