Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM › from 2021.06
RM27T0E _58 Vehicle Interior _053733 METER / GAUGE / DISPLAY _0261082 METER / GAUGE SYSTEM C

METER / GAUGE / DISPLAY  METER / GAUGE SYSTEM  B1507  Open in Turn Signal Circuit  B1508  Short in Turn Signal / Hazard Flasher Circuit  


DESCRIPTION

DTC Code DTC Detection Condition Trouble Area
B1507 Open in turn signal light circuit.

for Halogen Headlight (w/ Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight cord

-

Side turn signal light assembly

-

Outer mirror retractor

-

Outer mirror control ECU assembly

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for Halogen Headlight (w/o Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight cord

-

Side turn signal light assembly

-

Outer mirror retractor

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for LED Headlight (w/ Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight unit assembly

-

No. 1 headlight ECU sub-assembly

-

Side turn signal light assembly

-

Outer mirror retractor

-

Outer mirror control ECU assembly

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for LED Headlight (w/o Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight unit assembly

-

No. 1 headlight ECU sub-assembly

-

Side turn signal light assembly

-

Outer mirror retractor

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



B1508 Short in turn signal light circuit or hazard warning light circuit.

for Halogen Headlight (w/ Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight cord

-

Side turn signal light assembly

-

Outer mirror retractor

-

Outer mirror control ECU assembly

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for Halogen Headlight (w/o Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight cord

-

Side turn signal light assembly

-

Outer mirror retractor

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for LED Headlight (w/ Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight unit assembly

-

No. 1 headlight ECU sub-assembly

-

Side turn signal light assembly

-

Outer mirror retractor

-

Outer mirror control ECU assembly

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly



for LED Headlight (w/o Reverse Shift-linked Mirror):

-

Harness or connector

-

Front turn signal light bulb socket

-

Headlight unit assembly

-

No. 1 headlight ECU sub-assembly

-

Side turn signal light assembly

-

Outer mirror retractor

-

Rear combination light socket and wire sub-assembly

-

Combination meter assembly




WIRING DIAGRAM

E379272E03
0.156,0.104 4.115,0.344 3.958,0.24 12 false for Halogen Headlight (w/ Reverse Shift-linked Mirror): 1.906,1.292 3.542,1.49 1.635,0.198 10 false Front Turn Signal Light 1.427,1.729 3.99,1.917 2.563,0.188 10 false Front Turn Signal Light Bulb Socket LH 1.281,2.188 3.802,2.885 2.521,0.698 10 false A110 1.271,2.344 2.51,2.521 1.24,0.177 10 false Headlight Cord LH 1.073,0.958 1.25,1.156 0.177,0.198 10 false 2 0.635,0.948 0.813,1.135 0.177,0.188 10 false E 0.427,0.958 0.604,1.135 0.177,0.177 10 false 3 4.073,0.948 4.25,1.146 0.177,0.198 10 false 1 4.656,0.958 4.833,1.146 0.177,0.188 10 false B 4.896,0.948 5.073,1.135 0.177,0.188 10 false 4 5.542,0.958 5.719,1.146 0.177,0.188 10 false 8 5.729,1.073 5.906,1.26 0.177,0.188 10 false LL 3.313,4.781 4.531,5.115 1.219,0.333 10 false Outer Mirror Control ECU Assembly LH 4.531,3.438 4.865,3.615 0.333,0.177 10 false K12 4.531,4.302 4.865,4.479 0.333,0.177 10 false K12 4.104,3.438 4.438,3.615 0.333,0.177 10 false TRNI 4.115,4.313 4.448,4.49 0.333,0.177 10 false GND 4.583,3.24 4.917,3.417 0.333,0.177 10 false 11 4.635,4.115 4.781,4.313 0.146,0.198 10 false 7 3.427,3.438 3.854,3.604 0.427,0.167 10 false TRN+ 3.438,4.313 3.865,4.479 0.427,0.167 10 false HTR- 3.052,3.448 3.385,3.625 0.333,0.177 10 false z18 3.052,4.313 3.385,4.49 0.333,0.177 10 false z18 3.104,3.24 3.323,3.427 0.219,0.188 10 false 16 3.073,4.104 3.292,4.292 0.219,0.188 10 false 12 0.531,3.813 2.896,4.031 2.365,0.219 10 false Side Turn Signal Light Assembly LH 0.583,4.781 2.26,4.969 1.677,0.188 10 false Outer Mirror Retractor LH 3.479,6.104 3.813,6.281 0.333,0.177 10 false TRN 3.875,6.094 4.021,6.292 0.146,0.198 10 false 3 1.427,6.094 1.646,6.271 0.219,0.177 10 false E 1.208,6.104 1.354,6.302 0.146,0.198 10 false 4 1.854,6.49 3.365,6.688 1.51,0.198 10 false Rear Turn Signal Light 1.458,7.281 1.792,7.458 0.333,0.177 10 false R22 1.448,7.448 3.375,7.802 1.927,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly LH 5.51,8.031 5.917,8.219 0.406,0.188 10 false G195 5.51,8.198 6.677,8.583 1.167,0.385 10 false Combination Meter Assembly

E379273E01
0.208,0.135 4.188,0.375 3.979,0.24 12 false for Halogen Headlight (w/ Reverse Shift-linked Mirror): 1.917,1.313 3.5,1.521 1.583,0.208 10 false Front Turn Signal Light 1.49,1.708 3.948,1.885 2.458,0.177 10 false Front Turn Signal Light Bulb Socket LH 1.323,2.188 1.729,2.365 0.406,0.177 10 false A112 1.313,2.344 2.604,2.531 1.292,0.188 10 false Headlight Cord RH 0.438,0.948 0.604,1.115 0.167,0.167 10 false 3 0.646,0.938 0.813,1.104 0.167,0.167 10 false E 1.083,0.958 1.25,1.125 0.167,0.167 10 false 2 4.083,0.948 4.25,1.115 0.167,0.167 10 false 1 4.667,0.948 4.833,1.115 0.167,0.167 10 false B 4.896,0.948 5.063,1.115 0.167,0.167 10 false 4 5.76,1.063 6.031,1.24 0.271,0.177 10 false LR 5.5,0.948 5.771,1.125 0.271,0.177 10 false 13 4.094,3.448 4.469,3.625 0.375,0.177 10 false TRNI 4.104,4.302 4.469,4.479 0.365,0.177 10 false GND 3.073,3.438 3.354,3.615 0.281,0.177 10 false z19 3.052,4.302 3.333,4.479 0.281,0.177 10 false z19 4.542,3.448 4.823,3.625 0.281,0.177 10 false J12 4.542,4.313 4.823,4.49 0.281,0.177 10 false J12 3.115,3.25 3.396,3.427 0.281,0.177 10 false 16 3.094,4.125 3.375,4.302 0.281,0.177 10 false 12 3.438,3.448 3.813,3.625 0.375,0.177 10 false TRN+ 3.448,4.313 3.823,4.49 0.375,0.177 10 false HTR- 0.5,3.813 2.771,3.99 2.271,0.177 10 false Side Turn Signal Light Assembly RH 0.51,4.781 2.292,4.958 1.781,0.177 10 false Outer Mirror Retractor RH 4.573,3.25 4.854,3.427 0.281,0.177 10 false 11 4.604,4.104 4.771,4.292 0.167,0.188 10 false 7 3.323,4.781 4.573,5.146 1.25,0.365 10 false Outer Mirror Control ECU Assembly RH 1.865,6.479 3.281,6.677 1.417,0.198 10 false Rear Turn Signal Light 3.49,6.104 3.854,6.281 0.365,0.177 10 false TRN 1.427,6.094 1.792,6.271 0.365,0.177 10 false E 3.854,6.104 4.021,6.292 0.167,0.188 10 false 3 1.229,6.104 1.396,6.292 0.167,0.188 10 false 4 1.438,7.271 2.458,7.448 1.021,0.177 10 false Q31*1, R21*2 1.448,7.448 3.385,7.813 1.938,0.365 10 false Rear Combination Light Socket and Wire Sub-assembly RH 5.563,7.771 5.969,7.948 0.406,0.177 10 false G195 5.563,7.948 6.813,8.302 1.25,0.354 10 false Combination Meter Assembly 0.302,8.156 1.427,8.344 1.125,0.188 10 false *1: for 3 Door 0.302,8.448 1.177,8.646 0.875,0.198 10 false *2: for 5 Door

E379274E01
0.281,0.125 4.385,0.354 4.104,0.229 12 false for Halogen Headlight (w/o Reverse Shift-linked Mirror): 1.948,1.302 3.521,1.479 1.573,0.177 10 false Front Turn Signal Light 1.458,1.719 3.969,1.896 2.51,0.177 10 false Front Turn Signal Light Bulb Socket LH 1.365,2.188 1.75,2.354 0.385,0.167 10 false A110 1.354,2.344 2.594,2.521 1.24,0.177 10 false Headlight Cord LH 4.063,0.958 4.292,1.135 0.229,0.177 10 false 1 4.688,0.948 4.917,1.125 0.229,0.177 10 false B 4.885,0.948 5.115,1.125 0.229,0.177 10 false 4 1.094,0.938 1.323,1.115 0.229,0.177 10 false 2 0.667,0.938 0.896,1.115 0.229,0.177 10 false E 0.448,0.958 0.677,1.135 0.229,0.177 10 false 3 5.75,1.073 5.979,1.25 0.229,0.177 10 false LL 5.552,0.958 5.781,1.135 0.229,0.177 10 false 8 0.594,3.813 2.896,4 2.302,0.188 10 false Side Turn Signal Light Assembly LH 0.396,4.771 0.781,4.938 0.385,0.167 10 false K1 0.375,4.927 2.229,5.125 1.854,0.198 10 false Outer Mirror Retractor LH 2.823,3.323 3.208,3.49 0.385,0.167 10 false B 3.021,3.313 3.406,3.479 0.385,0.167 10 false 10 2.823,4.208 3.208,4.375 0.385,0.167 10 false E 3.031,4.188 3.417,4.354 0.385,0.167 10 false 11 1.875,6.479 3.427,6.677 1.552,0.198 10 false Rear Turn Signal Light 1.479,7.271 2.052,7.438 0.573,0.167 10 false R22 1.479,7.438 3.469,7.813 1.99,0.375 10 false Rear Combination Light Socket and Wire Sub-assembly LH 1.427,6.104 1.698,6.302 0.271,0.198 10 false E 1.219,6.104 1.49,6.302 0.271,0.198 10 false 4 3.469,6.094 4.042,6.26 0.573,0.167 10 false TRN 3.854,6.094 4.156,6.271 0.302,0.177 10 false 3 5.583,7.979 6.156,8.146 0.573,0.167 10 false G195 5.573,8.146 6.781,8.521 1.208,0.375 10 false Combination Meter Assembly

E379275E01
0.344,0.104 4.531,0.323 4.188,0.219 12 false for Halogen Headlight (w/o Reverse Shift-linked Mirror): 1.906,1.302 3.604,1.49 1.698,0.188 10 false Front Turn Signal Light 1.458,1.719 4.083,1.906 2.625,0.188 10 false Front Turn Signal Light Bulb Socket LH 1.24,2.198 1.667,2.365 0.427,0.167 10 false A112 1.229,2.365 2.615,2.573 1.385,0.208 10 false Headlight Cord RH 4.083,0.958 4.271,1.146 0.188,0.188 10 false 1 4.677,0.958 4.865,1.146 0.188,0.188 10 false B 4.885,0.958 5.073,1.146 0.188,0.188 10 false 4 5.448,0.948 5.635,1.135 0.188,0.188 10 false 13 5.729,1.063 5.99,1.25 0.26,0.188 10 false LR 0.635,0.938 0.823,1.125 0.188,0.188 10 false E 1.094,0.958 1.281,1.146 0.188,0.188 10 false 2 0.438,0.948 0.625,1.135 0.188,0.188 10 false 3 2.792,3.313 2.979,3.5 0.188,0.188 10 false B 3.01,3.302 3.198,3.49 0.188,0.188 10 false 10 2.781,4.188 2.969,4.375 0.188,0.188 10 false E 3.021,4.188 3.208,4.375 0.188,0.188 10 false 11 0.552,3.813 2.885,4.01 2.333,0.198 10 false Side Turn Signal Light Assembly RH 0.5,4.76 0.708,4.938 0.208,0.177 10 false J2 0.49,4.927 2.323,5.115 1.833,0.188 10 false Outer Mirror Retractor RH 1.896,6.479 3.448,6.677 1.552,0.198 10 false Rear Turn Signal Light 1.448,7.281 2.521,7.479 1.073,0.198 10 false Q31*1, R21*2 1.448,7.448 3.448,7.813 2,0.365 10 false Rear Combination Light Socket and Wire Sub-assembly RH 3.479,6.104 3.844,6.281 0.365,0.177 10 false TRN 3.854,6.104 4,6.302 0.146,0.198 10 false 3 1.427,6.094 1.792,6.271 0.365,0.177 10 false E 1.219,6.104 1.583,6.281 0.365,0.177 10 false 4 5.5,7.792 5.865,7.969 0.365,0.177 10 false G195 5.5,7.948 6.823,8.313 1.323,0.365 10 false Combination Meter Assembly 0.365,8.125 1.49,8.313 1.125,0.188 10 false *1: for 3 Door 0.354,8.417 1.479,8.604 1.125,0.188 10 false *2: for 5 Door

E379276E03
0.365,0.135 4.115,0.365 3.75,0.229 12 false for LED Headlight (w/ Reverse Shift-linked Mirror): 0.927,1.281 2.396,1.469 1.469,0.188 10 false Front Turn Signal Light 0.448,1.656 2.906,1.844 2.458,0.188 10 false Front Turn Signal Light Bulb Socket LH 0.479,2.406 2.344,2.573 1.865,0.167 10 false Headlight Unit Assembly LH 2.615,0.958 2.865,1.135 0.25,0.177 10 false 1 0.594,0.969 0.844,1.146 0.25,0.177 10 false 2 3.125,1.063 3.375,1.24 0.25,0.177 10 false A 3.125,1.938 3.375,2.115 0.25,0.177 10 false A 3.135,0.875 3.281,1.063 0.146,0.188 10 false 9 3.083,1.74 3.271,1.917 0.188,0.177 10 false 13 3.448,1.063 4.01,1.25 0.563,0.188 10 false TURN+ 3.438,1.938 4,2.125 0.563,0.188 10 false TURN- 4.125,1.063 4.5,1.24 0.375,0.177 10 false TNS 4.104,1.927 4.479,2.104 0.375,0.177 10 false GND 4.5,1.073 4.875,1.25 0.375,0.177 10 false A130 4.49,1.938 4.865,2.115 0.375,0.177 10 false A130 4.583,0.865 4.792,1.021 0.208,0.156 10 false 11 4.583,1.74 4.792,1.917 0.208,0.177 10 false 12 5.531,0.958 5.74,1.135 0.208,0.177 10 false 8 5.75,1.073 5.958,1.229 0.208,0.156 10 false LL 3.313,2.396 4.604,2.76 1.292,0.365 10 false No. 1 Headlight ECU Sub-assembly LH 0.542,4.781 2.198,4.958 1.656,0.177 10 false Outer Mirror Retractor LH 0.5,3.802 2.969,3.979 2.469,0.177 10 false Side Turn Signal Light Assembly LH 3.063,3.438 3.313,3.615 0.25,0.177 10 false z18 3.042,4.313 3.292,4.49 0.25,0.177 10 false z18 3.427,3.448 3.865,3.635 0.438,0.188 10 false TRN+ 3.427,4.313 3.865,4.5 0.438,0.188 10 false HTR- 4.073,3.448 4.51,3.635 0.438,0.188 10 false TRNI 4.104,4.313 4.542,4.5 0.438,0.188 10 false GND 3.104,3.24 3.365,3.427 0.26,0.188 10 false 16 3.083,4.115 3.344,4.302 0.26,0.188 10 false 12 4.542,3.448 4.979,3.635 0.438,0.188 10 false K12 4.594,3.24 4.781,3.438 0.188,0.198 10 false 11 4.531,4.313 4.969,4.5 0.438,0.188 10 false K12 4.635,4.125 4.781,4.313 0.146,0.188 10 false 7 3.313,4.781 4.552,5.146 1.24,0.365 10 false Outer Mirror Control ECU Assembly LH 1.927,6.458 3.448,6.667 1.521,0.208 10 false Rear Turn Signal Light 1.458,7.281 1.833,7.469 0.375,0.188 10 false R22 1.458,7.448 3.385,7.802 1.927,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly LH 1.427,6.083 1.656,6.271 0.229,0.188 10 false E 1.208,6.083 1.438,6.271 0.229,0.188 10 false 4 3.49,6.094 3.865,6.281 0.375,0.188 10 false TRN 3.875,6.083 4.25,6.271 0.375,0.188 10 false 3 5.49,7.969 5.865,8.156 0.375,0.188 10 false G195 5.479,8.135 6.688,8.51 1.208,0.375 10 false Combination Meter Assembly

E379277E01
0.396,0.104 4.115,0.344 3.719,0.24 12 false for LED Headlight (w/ Reverse Shift-linked Mirror): 0.99,1.292 2.51,1.479 1.521,0.188 10 false Front Turn Signal Light 0.438,1.688 3.021,1.865 2.583,0.177 10 false Front Turn Signal Light Bulb Socket RH 0.542,2.396 2.427,2.563 1.885,0.167 10 false Headlight Unit Assembly RH 2.625,0.969 2.75,1.156 0.125,0.188 10 false 1 0.604,0.979 0.729,1.167 0.125,0.188 10 false 2 3.125,1.063 3.25,1.25 0.125,0.188 10 false A 3.115,1.938 3.24,2.125 0.125,0.188 10 false A 3.135,0.875 3.26,1.063 0.125,0.188 10 false 9 3.094,1.729 3.281,1.885 0.188,0.156 10 false 13 3.438,1.073 3.948,1.25 0.51,0.177 10 false TURN+ 3.427,1.948 3.938,2.125 0.51,0.177 10 false TURN- 4.083,1.938 4.594,2.115 0.51,0.177 10 false GND 4.104,1.073 4.615,1.25 0.51,0.177 10 false TNS 4.5,1.073 5.01,1.25 0.51,0.177 10 false A103 4.49,1.938 5,2.115 0.51,0.177 10 false A103 4.573,0.865 5.083,1.042 0.51,0.177 10 false 11 4.573,1.729 5.083,1.906 0.51,0.177 10 false 12 5.76,1.073 6.271,1.25 0.51,0.177 10 false LR 5.49,0.958 6,1.135 0.51,0.177 10 false 13 3.292,2.406 4.552,2.76 1.26,0.354 10 false No. 1 Headlight ECU Sub-assembly RH 0.531,3.802 3,4 2.469,0.198 10 false Side Turn Signal Light Assembly RH 3.302,4.781 4.563,5.146 1.26,0.365 10 false Outer Mirror Control ECU Assembly RH 3.063,3.438 3.396,3.604 0.333,0.167 10 false z19 3.063,4.302 3.396,4.469 0.333,0.167 10 false z19 3.448,3.448 3.844,3.625 0.396,0.177 10 false TRN+ 3.427,4.302 3.823,4.479 0.396,0.177 10 false HTR- 4.104,3.438 4.5,3.615 0.396,0.177 10 false TRNI 4.552,3.438 4.948,3.615 0.396,0.177 10 false J12 4.573,3.24 4.969,3.417 0.396,0.177 10 false 11 4.104,4.302 4.5,4.479 0.396,0.177 10 false GND 4.531,4.313 4.927,4.49 0.396,0.177 10 false J12 4.635,4.115 5.031,4.292 0.396,0.177 10 false 7 1.906,6.479 3.458,6.688 1.552,0.208 10 false Rear Turn Signal Light 1.49,7.281 2.521,7.479 1.031,0.198 10 false Q31*1, R21*2 1.49,7.458 3.427,7.813 1.938,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly RH 3.469,6.104 3.865,6.281 0.396,0.177 10 false TRN 3.875,6.104 4.271,6.281 0.396,0.177 10 false 3 1.438,6.115 1.833,6.292 0.396,0.177 10 false E 1.219,6.115 1.615,6.292 0.396,0.177 10 false 4 5.563,7.781 5.958,7.958 0.396,0.177 10 false G195 5.563,7.958 6.865,8.323 1.302,0.365 10 false Combination Meter Assembly 0.448,8.125 1.479,8.323 1.031,0.198 10 false *1: for 3 Door 0.448,8.396 1.479,8.594 1.031,0.198 10 false *2: for 5 Door 0.594,4.771 3.063,4.969 2.469,0.198 10 false Outer Mirror Retractor RH 3.094,3.25 3.427,3.417 0.333,0.167 10 false 16 3.104,4.115 3.438,4.281 0.333,0.167 10 false 12

E379278E04
0.396,0.104 4.313,0.333 3.917,0.229 12 false for LED Headlight (w/o Reverse Shift-linked Mirror): 0.99,1.271 2.604,1.458 1.615,0.188 10 false Front Turn Signal Light 0.521,1.667 2.99,1.854 2.469,0.188 10 false Front Turn Signal Light Bulb Socket LH 0.49,2.406 2.469,2.594 1.979,0.188 10 false Headlight Unit Assembly LH 0.583,0.958 0.76,1.156 0.177,0.198 10 false 2 2.604,0.958 2.781,1.156 0.177,0.198 10 false 1 3.125,1.063 3.302,1.26 0.177,0.198 10 false A 3.115,1.917 3.292,2.115 0.177,0.198 10 false A 3.135,0.865 3.313,1.063 0.177,0.198 10 false 9 3.427,1.073 3.927,1.25 0.5,0.177 10 false TURN+ 3.427,1.927 3.927,2.104 0.5,0.177 10 false TURN- 3.083,1.729 3.313,1.906 0.229,0.177 10 false 13 4.125,1.063 4.625,1.24 0.5,0.177 10 false TNS 4.104,1.927 4.604,2.104 0.5,0.177 10 false GND 4.5,1.063 5,1.24 0.5,0.177 10 false A130 4.5,1.927 5,2.104 0.5,0.177 10 false A130 4.583,0.844 5.083,1.021 0.5,0.177 10 false 11 4.594,1.74 5.094,1.917 0.5,0.177 10 false 12 5.531,0.948 6.031,1.125 0.5,0.177 10 false 8 5.74,1.073 6.24,1.25 0.5,0.177 10 false LL 3.271,2.396 4.573,2.75 1.302,0.354 10 false No. 1 Headlight ECU Sub-assembly LH 0.521,3.833 2.823,4.021 2.302,0.188 10 false Side Turn Signal Light Assembly LH 0.354,4.771 0.698,4.948 0.344,0.177 10 false K1 0.344,4.938 1.99,5.125 1.646,0.188 10 false Outer Mirror Retractor LH 2.813,3.323 3,3.49 0.188,0.167 10 false B 3.021,3.313 3.208,3.479 0.188,0.167 10 false 10 2.813,4.198 3,4.365 0.188,0.167 10 false E 3.021,4.177 3.208,4.344 0.188,0.167 10 false 11 1.854,6.479 4.156,6.667 2.302,0.188 10 false Rear Turn Signal Light 1.427,6.094 1.844,6.271 0.417,0.177 10 false E 3.49,6.083 3.906,6.26 0.417,0.177 10 false TRN 3.865,6.083 4.281,6.26 0.417,0.177 10 false 3 1.208,6.094 1.625,6.271 0.417,0.177 10 false 4 1.438,7.281 1.844,7.479 0.406,0.198 10 false R22 1.438,7.448 3.365,7.802 1.927,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly LH 5.604,7.958 6.01,8.156 0.406,0.198 10 false G195 5.604,8.125 6.844,8.49 1.24,0.365 10 false Combination Meter Assembly

E379279E01
0.479,0.125 4.385,0.365 3.906,0.24 12 false for LED Headlight (w/o Reverse Shift-linked Mirror): 0.99,1.302 2.521,1.5 1.531,0.198 10 false Front Turn Signal Light 0.521,1.656 3.094,1.844 2.573,0.188 10 false Front Turn Signal Light Bulb Socket RH 0.573,2.406 2.875,2.625 2.302,0.219 10 false Headlight Unit Assembly RH 3.302,2.417 4.594,2.781 1.292,0.365 10 false No. 1 Headlight ECU Sub-assembly RH 3.438,1.083 3.948,1.26 0.51,0.177 10 false TURN+ 3.438,1.948 3.948,2.125 0.51,0.177 10 false TURN- 3.125,1.063 3.313,1.24 0.188,0.177 10 false A 3.115,1.938 3.302,2.115 0.188,0.177 10 false A 2.635,0.958 2.823,1.135 0.188,0.177 10 false 1 3.094,1.74 3.281,1.917 0.188,0.177 10 false 13 4.115,1.063 4.625,1.24 0.51,0.177 10 false TNS 4.104,1.938 4.615,2.115 0.51,0.177 10 false GND 4.5,1.063 5.01,1.24 0.51,0.177 10 false A103 4.5,1.938 5.01,2.115 0.51,0.177 10 false A103 4.583,0.854 5.094,1.031 0.51,0.177 10 false 11 4.583,1.74 5.094,1.917 0.51,0.177 10 false 12 5.458,0.948 5.969,1.125 0.51,0.177 10 false 13 5.75,1.073 6.26,1.25 0.51,0.177 10 false LR 0.531,3.813 2.833,4.031 2.302,0.219 10 false Side Turn Signal Light Assembly RH 0.521,4.938 2.823,5.156 2.302,0.219 10 false Outer Mirror Retractor RH 0.531,4.771 0.823,4.938 0.292,0.167 10 false J2 2.781,3.323 3.073,3.49 0.292,0.167 10 false B 3.01,3.313 3.302,3.479 0.292,0.167 10 false 10 2.813,4.208 3.104,4.375 0.292,0.167 10 false E 3.021,4.198 3.313,4.365 0.292,0.167 10 false 11 3.865,6.104 4.156,6.271 0.292,0.167 10 false 3 3.469,6.115 3.76,6.281 0.292,0.167 10 false TRN 1.927,6.479 3.563,6.688 1.635,0.208 10 false Rear Turn Signal Light 1.417,6.094 1.708,6.26 0.292,0.167 10 false E 1.208,6.104 1.5,6.271 0.292,0.167 10 false 4 1.521,7.271 2.49,7.458 0.969,0.188 10 false Q31*1, R21*2 1.521,7.448 3.469,7.802 1.948,0.354 10 false Rear Combination Light Socket and Wire Sub-assembly RH 5.563,7.781 6.052,7.958 0.49,0.177 10 false G195 5.563,7.948 6.854,8.333 1.292,0.385 10 false Combination Meter Assembly 0.281,8.146 1.396,8.333 1.115,0.188 10 false *1: for 3 Door 0.271,8.448 1.385,8.635 1.115,0.188 10 false *2: for 5 Door 0.594,0.969 0.781,1.146 0.188,0.177 10 false 2 3.135,0.865 3.323,1.042 0.188,0.177 10 false 9

CAUTION / NOTICE / HINT

NOTICE:

Inspect the bulbs for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK FOR DTC

b.

Recheck for DTCs and check that no DTCs are output.

Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DTC CHECK / CLEAR

OK:

B1507 and B1508 are not output.



Result:
Proceed to
OK
NG



OK

NG

2.CHECK VEHICLE TYPE
2.CHECK VEHICLE TYPE
a.

Check the vehicle type.


Result:
Result Proceed to
for Halogen Headlight (w/ Reverse Shift-linked Mirror) A
for Halogen Headlight (w/o Reverse Shift-linked Mirror) B
for LED Headlight (w/ Reverse Shift-linked Mirror) C
for LED Headlight (w/o Reverse Shift-linked Mirror) D



A

3.INSPECT LIGHTS

B

24.INSPECT LIGHTS

C

37.INSPECT LIGHTS

D

52.INSPECT LIGHTS
3.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

4.CHECK TURN SIGNAL LIGHTS (LH SIDE)

B

14.CHECK TURN SIGNAL LIGHTS (RH SIDE)
4.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light (LH side) does not blink. A
Side turn signal light (LH side) does not blink. B
Rear turn signal light (LH side) does not blink. C



A

5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

12.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
5.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A110-4 (B) - J195-8 (LL) Always Below 1 Ω
A110-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A110-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT HEADLIGHT CORD LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.INSPECT HEADLIGHT CORD LH

b.
E379280E01
1.25,0.948 0.927,0.344 0.927,0.344 0.781,0.344 true 1.625,0.938 1.823,0.292 1.823,0.292 1.948,0.292 true 0.635,0.281 0.792,0.458 0.156,0.177 10 false B 2.01,0.219 2.188,0.406 0.177,0.188 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
4 (B) - 1 Always Below 1 Ω
3 (E) - 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4 (B) - 3 (E) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET LH

NG

7.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET LH
a.

Remove the front turn signal light bulb socket LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>DISASSEMBLY


b.
E379281

Apply battery voltage and check the operation of the front turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 1
Negative (-) → 2
Front turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FRONT TURN SIGNAL LIGHT BULB SOCKET LH

8.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
K12-11 (TRNI) - G195-8 (LL) Always Below 1 Ω
K12-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
K12-11 (TRNI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

10.CHECK OUTER MIRROR RETRACTOR LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

10.CHECK OUTER MIRROR RETRACTOR LH
a.

Disconnect the z18 outer mirror retractor LH connector.


b.
B487974C06
1.542,0.26 1.875,0.49 0.333,0.229 2.104,1.448 2.302,1.813 2.302,1.813 2.438,1.813 true 1.667,1.469 1.865,1.833 1.865,1.833 1.75,1.833 true 0.188,0.125 0.375,0.333 0.188,0.208 10 false *a 2.469,1.74 2.906,1.917 0.438,0.177 10 false TRN+ 1.385,1.75 1.885,1.927 0.5,0.177 10 false HTR- 1.594,0.292 1.885,0.458 0.292,0.167 10 false z18
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly LH)


Apply battery voltage and check the operation of the side turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → z18-16 (TRN+)
Negative (-) → z18-12 (HTR-)
Side turn signal light illuminates



Result:
Proceed to
OK
NG



OK

11.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH

NG

REPLACE OUTER MIRROR RETRACTOR LH

11.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY LH
B343031E32
4.656,1.26 5.01,0.198 5.01,0.198 5.167,0.198 true 4.021,1.042 4.26,0.177 4.26,0.177 4.104,0.177 true 2.719,1.229 2.844,0.198 2.844,0.198 3,0.198 true 1.875,1.24 1.333,0.719 1.333,0.719 1.208,0.719 true 0.813,0.646 1.271,0.823 0.458,0.177 10 false TRN+ 3.063,0.115 3.521,0.292 0.458,0.177 10 false HTR- 5.219,0.125 5.677,0.292 0.458,0.167 10 false TRNI 3.771,0.104 4.229,0.271 0.458,0.167 10 false GND

a.

Remove the outer mirror control ECU assembly LH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
16 (TRN+) - 11 (TRNI) Always Below 1 Ω
12 (HTR-) - 7 (GND) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
16 (TRN+) - 12 (HTR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY LH

12.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
R22-3 (TRN) - G195-8 (LL) Always Below 1 Ω
R22-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
R22-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH
a.

Remove the rear combination light socket and wire sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.
E379285E01
1,0.375 1.177,0.375 1.177,0.375 1.427,0.969 true 2.5,1.729 2.344,1.729 2.344,1.729 1.896,1.281 true 2.563,1.656 2.708,1.833 0.146,0.177 10 false E 0.688,0.302 1.01,0.479 0.323,0.177 10 false TRN

Apply battery voltage and check the operation of the rear turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 3 (TRN)
Negative (-) → 4 (E)
Rear turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

14.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light (RH side) does not blink. A
Side turn signal light (RH side) does not blink. B
Rear turn signal light (RH side) does not blink. C



A

15.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

18.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

22.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
15.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A112-4 (B) - J195-13 (LR) Always Below 1 Ω
A112-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A112-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT HEADLIGHT CORD RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT HEADLIGHT CORD RH

b.
E379280E01
1.25,0.948 0.927,0.344 0.927,0.344 0.781,0.344 true 1.625,0.938 1.823,0.292 1.823,0.292 1.948,0.292 true 0.635,0.281 0.792,0.458 0.156,0.177 10 false B 2.01,0.219 2.188,0.406 0.177,0.188 10 false E

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
4 (B) - 1 Always Below 1 Ω
3 (E) - 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
4 (B) - 3 (E) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET RH

NG

17.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET RH
a.

Remove the front turn signal light bulb socket RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for Halogen Headlight)>DISASSEMBLY


b.
E379281

Apply battery voltage and check the operation of the front turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 1
Negative (-) → 2
Front turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE FRONT TURN SIGNAL LIGHT BULB SOCKET RH

18.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J12-11 (TRNI) - G195-13 (LR) Always Below 1 Ω
J12-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J12-11 (TRNI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

20.CHECK OUTER MIRROR RETRACTOR RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

20.CHECK OUTER MIRROR RETRACTOR RH
a.

Disconnect the z19 outer mirror retractor RH connector.


b.
B487974C07
1.542,0.26 1.875,0.49 0.333,0.229 2.104,1.448 2.302,1.813 2.302,1.813 2.438,1.813 true 1.667,1.469 1.865,1.833 1.865,1.833 1.75,1.833 true 0.188,0.125 0.375,0.333 0.188,0.208 10 false *a 2.469,1.74 2.906,1.917 0.438,0.177 10 false TRN+ 1.385,1.75 1.885,1.927 0.5,0.177 10 false HTR- 1.594,0.292 1.885,0.458 0.292,0.167 10 false z19
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Apply battery voltage and check the operation of the side turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → z19-16 (TRN+)
Negative (-) → z19-12 (HTR-)
Side turn signal light illuminates



Result:
Proceed to
OK
NG



OK

21.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPLACE OUTER MIRROR RETRACTOR RH

21.INSPECT OUTER MIRROR CONTROL ECU ASSEMBLY RH
B343031E32
4.656,1.26 5.01,0.198 5.01,0.198 5.167,0.198 true 4.021,1.042 4.26,0.177 4.26,0.177 4.104,0.177 true 2.719,1.229 2.844,0.198 2.844,0.198 3,0.198 true 1.875,1.24 1.333,0.719 1.333,0.719 1.208,0.719 true 0.813,0.646 1.271,0.823 0.458,0.177 10 false TRN+ 3.063,0.115 3.521,0.292 0.458,0.177 10 false HTR- 5.219,0.125 5.677,0.292 0.458,0.167 10 false TRNI 3.771,0.104 4.229,0.271 0.458,0.167 10 false GND

a.

Remove the outer mirror control ECU assembly RH.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER MIRROR CONTROL ECU>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
16 (TRN+) - 11 (TRNI) Always Below 1 Ω
12 (HTR-) - 7 (GND) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
16 (TRN+) - 12 (HTR-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

22.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - G195-13 (LR)*1 Always Below 1 Ω
R21-3 (TRN) - G195-13 (LR)*2 Always Below 1 Ω
Q31-4 (E) - Body ground*1 Always Below 1 Ω
R21-4 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - Body ground*1 Always 10 kΩ or higher
R21-3 (TRN) - Body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH
a.

Remove the rear combination light socket and wire sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>REAR COMBINATION LIGHT ASSEMBLY>DISASSEMBLY


b.
E379285E01
1,0.375 1.177,0.375 1.177,0.375 1.427,0.969 true 2.5,1.729 2.344,1.729 2.344,1.729 1.896,1.281 true 2.563,1.656 2.708,1.833 0.146,0.177 10 false E 0.688,0.302 1.01,0.479 0.323,0.177 10 false TRN

Apply battery voltage and check the operation of the rear turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 3 (TRN)
Negative (-) → 4 (E)
Rear turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

24.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

25.CHECK TURN SIGNAL LIGHTS (LH SIDE)

B

31.CHECK TURN SIGNAL LIGHTS (RH SIDE)
25.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light (LH side) does not blink. A
Side turn signal light (LH side) does not blink. B
Rear turn signal light (LH side) does not blink. C



A

26.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

27.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

30.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
26.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A110-4 (B) - J195-8 (LL) Always Below 1 Ω
A110-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A110-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT HEADLIGHT CORD LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

27.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
K1-10 (B) - G195-8 (LL) Always Below 1 Ω
K1-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
K1-10 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

28.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

28.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH
a.

Remove the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

29.INSPECT OUTER MIRROR RETRACTOR LH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY LH

29.INSPECT OUTER MIRROR RETRACTOR LH
a.

Remove the outer mirror retractor LH connector.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.
E379284E01
1.406,1.833 1.729,1.479 true 2.083,1.865 1.844,1.458 true 1.292,1.833 1.448,2 0.156,0.167 10 false B 2.104,1.865 2.26,2.031 0.156,0.167 10 false E

Apply battery voltage and check the operation of the side turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 10 (B)
Negative (-) → 11 (E)
Side turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OUTER MIRROR RETRACTOR LH

30.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A110 headlight cord LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
R22-3 (TRN) - G195-8 (LL) Always Below 1 Ω
R22-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
R22-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

31.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light (RH side) does not blink. A
Side turn signal light (RH side) does not blink. B
Rear turn signal light (RH side) does not blink. C



A

32.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

33.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

36.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
32.CHECK HARNESS AND CONNECTOR (HEADLIGHT CORD RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A112-4 (B) - J195-13 (LR) Always Below 1 Ω
A112-3 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A112-4 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT HEADLIGHT CORD RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

33.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J2-10 (B) - G195-13 (LR) Always Below 1 Ω
J2-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J2-10 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

34.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH
a.

Remove the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>REMOVAL


b.

Inspect the side turn signal light assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>SIDE TURN SIGNAL LIGHT ASSEMBLY>INSPECTION


Result:
Proceed to
OK
NG



OK

35.INSPECT OUTER MIRROR RETRACTOR RH

NG

REPLACE SIDE TURN SIGNAL LIGHT ASSEMBLY RH

35.INSPECT OUTER MIRROR RETRACTOR RH
a.

Remove the outer mirror retractor RH connector.

Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL


b.
E379284E01
1.406,1.833 1.729,1.479 true 2.083,1.865 1.844,1.458 true 1.292,1.833 1.448,2 0.156,0.167 10 false B 2.104,1.865 2.26,2.031 0.156,0.167 10 false E

Apply battery voltage and check the operation of the side turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 10 (B)
Negative (-) → 11 (E)
Side turn signal light illuminates



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE OUTER MIRROR RETRACTOR RH

36.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A112 headlight cord RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - G195-13 (LR)*1 Always Below 1 Ω
R21-3 (TRN) - G195-13 (LR)*2 Always Below 1 Ω
Q31-4 (E) - Body ground*1 Always Below 1 Ω
R21-4 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - Body ground*1 Always 10 kΩ or higher
R21-3 (TRN) - Body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

37.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

38.CHECK TURN SIGNAL LIGHTS (LH SIDE)

B

45.CHECK TURN SIGNAL LIGHTS (RH SIDE)
38.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light (LH side) does not blink. A
Side turn signal light (LH side) does not blink. B
Rear turn signal light (LH side) does not blink. C



A

39.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

43.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

44.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
39.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A130-11 (TNS) - J195-8 (LL) Always Below 1 Ω
A130-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A130-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

40.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

40.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET LH
a.

Remove the front turn signal light bulb socket LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY


b.
E379281

Apply battery voltage and check the operation of the front turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 1
Negative (-) → 2
Front turn signal light illuminates



Result:
Proceed to
OK
NG



OK

41.INSPECT HEADLIGHT UNIT ASSEMBLY LH

NG

REPLACE FRONT TURN SIGNAL LIGHT BULB SOCKET LH

41.INSPECT HEADLIGHT UNIT ASSEMBLY LH
a.
E379282E01
1.521,0.26 1.906,0.5 0.385,0.24 2.302,1.375 2.427,0.438 2.427,0.438 2.594,0.438 true 1.281,1.583 1.135,2.219 1.135,2.219 0.99,2.219 true 1.677,0.292 1.823,0.469 0.146,0.177 10 false A 2.656,0.365 3.26,0.542 0.604,0.177 10 false TURN+ 0.531,2.135 1.083,2.313 0.552,0.177 10 false TURN-

Remove the headlight unit assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A-9 (TURN+) - 1 Always Below 1 Ω
A-13 (TURN-) - 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A-9 (TURN+) - A-13 (TURN-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

42.INSPECT NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

NG

42.INSPECT NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH
E379283E01
5.333,0.969 5.385,0.302 5.385,0.302 5.25,0.302 true 6.042,1.135 6.188,1.542 6.188,1.542 6.052,1.542 true 1.625,0.854 1.344,0.229 1.344,0.229 1.208,0.229 true 3.135,0.958 3.5,1.469 3.5,1.469 3.635,1.469 true 4.75,0.229 5.281,0.396 0.531,0.167 10 false TURN+ 5.583,1.448 6.115,1.615 0.531,0.167 10 false TURN- 0.906,0.156 1.25,0.333 0.344,0.177 10 false TNS 3.688,1.396 4.031,1.573 0.344,0.177 10 false GND

a.

Remove the No. 1 headlight ECU sub-assembly LH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
11 (TNS) - 9 (TURN+) Always Below 1 Ω
12 (GND) - 13 (TURN-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
11 (TNS) - 12 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH

43.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
K12-11 (TRNI) - G195-8 (LL) Always Below 1 Ω
K12-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
K12-11 (TRNI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

44.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K12 outer mirror control ECU assembly LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
R22-3 (TRN) - G195-8 (LL) Always Below 1 Ω
R22-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
R22-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

45.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light (RH side) does not blink. A
Side turn signal light (RH side) does not blink. B
Rear turn signal light (RH side) does not blink. C



A

46.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

50.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

51.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
46.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A103-11 (TNS) - J195-13 (LR) Always Below 1 Ω
A103-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A103-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

47.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

47.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET RH
a.

Remove the front turn signal light bulb socket RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY


b.
E379281

Apply battery voltage and check the operation of the front turn signal light.

OK:
Battery Connection Specified Condition
Positive (+) → 1
Negative (-) → 2
Front turn signal light illuminates



Result:
Proceed to
OK
NG



OK

48.INSPECT HEADLIGHT UNIT ASSEMBLY RH

NG

REPLACE FRONT TURN SIGNAL LIGHT BULB SOCKET RH

48.INSPECT HEADLIGHT UNIT ASSEMBLY RH
a.
E379282E01
1.521,0.26 1.906,0.5 0.385,0.24 2.302,1.375 2.427,0.438 2.427,0.438 2.594,0.438 true 1.281,1.583 1.135,2.219 1.135,2.219 0.99,2.219 true 1.677,0.292 1.823,0.469 0.146,0.177 10 false A 2.656,0.365 3.26,0.542 0.604,0.177 10 false TURN+ 0.531,2.135 1.083,2.313 0.552,0.177 10 false TURN-

Remove the headlight unit assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>REMOVAL


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A-9 (TURN+) - 1 Always Below 1 Ω
A-13 (TURN-) - 2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A-9 (TURN+) - A-13 (TURN-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

49.INSPECT NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

NG

49.INSPECT NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH
E379283E01
5.333,0.969 5.385,0.302 5.385,0.302 5.25,0.302 true 6.042,1.135 6.188,1.542 6.188,1.542 6.052,1.542 true 1.625,0.854 1.344,0.229 1.344,0.229 1.208,0.229 true 3.135,0.958 3.5,1.469 3.5,1.469 3.635,1.469 true 4.75,0.229 5.281,0.396 0.531,0.167 10 false TURN+ 5.583,1.448 6.115,1.615 0.531,0.167 10 false TURN- 0.906,0.156 1.25,0.333 0.344,0.177 10 false TNS 3.688,1.396 4.031,1.573 0.344,0.177 10 false GND

a.

Remove the No. 1 headlight ECU sub-assembly RH.

Click hereVehicle Exterior>LIGHTING (EXT)>HEADLIGHT ASSEMBLY(for LED Headlight)>DISASSEMBLY


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
11 (TNS) - 9 (TURN+) Always Below 1 Ω
12 (GND) - 13 (TURN-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
11 (TNS) - 12 (GND) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH

50.CHECK HARNESS AND CONNECTOR (OUTER MIRROR CONTROL ECU ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J12-11 (TRNI) - G195-13 (LR) Always Below 1 Ω
J12-7 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J12-11 (TRNI) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

51.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J12 outer mirror control ECU assembly RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - G195-13 (LR)*1 Always Below 1 Ω
R21-3 (TRN) - G195-13 (LR)*2 Always Below 1 Ω
Q31-4 (E) - Body ground*1 Always Below 1 Ω
R21-4 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - Body ground*1 Always 10 kΩ or higher
R21-3 (TRN) - Body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

52.INSPECT LIGHTS
a.

Inspect the illumination of each turn signal light.


Result:
Result Proceed to
LH side turn signal light does not illuminate. A
RH side turn signal light does not illuminate. B



A

53.CHECK TURN SIGNAL LIGHTS (LH SIDE)

B

57.CHECK TURN SIGNAL LIGHTS (RH SIDE)
53.CHECK TURN SIGNAL LIGHTS (LH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the left turn switch position.


c.

Check the operation of the turn signal lights (LH side).


Result:
Result Proceed to
Front turn signal light (LH side) does not blink. A
Side turn signal light (LH side) does not blink. B
Rear turn signal light (LH side) does not blink. C



A

54.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

55.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR LH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

56.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
54.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A130-11 (TNS) - J195-8 (LL) Always Below 1 Ω
A130-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A130-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

40.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

55.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
K1-10 (B) - G195-8 (LL) Always Below 1 Ω
K1-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
K1-10 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

28.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

56.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A130 No. 1 headlight ECU sub-assembly LH connector.


c.

Disconnect the K1 outer mirror retractor LH connector.


d.

Disconnect the R22 rear combination light socket and wire sub-assembly LH connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
R22-3 (TRN) - G195-8 (LL) Always Below 1 Ω
R22-4 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
R22-3 (TRN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY LH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

57.CHECK TURN SIGNAL LIGHTS (RH SIDE)
a.

Turn the ignition switch to ON.


b.

Set the headlight dimmer switch assembly to the right turn switch position.


c.

Check the operation of the turn signal lights (RH side).


Result:
Result Proceed to
Front turn signal light (RH side) does not blink. A
Side turn signal light (RH side) does not blink. B
Rear turn signal light (RH side) does not blink. C



A

58.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

B

59.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR RH - COMBINATION METER ASSEMBLY AND BODY GROUND)

C

60.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
58.CHECK HARNESS AND CONNECTOR (NO. 1 HEADLIGHT ECU SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A103-11 (TNS) - J195-13 (LR) Always Below 1 Ω
A103-12 (GND) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A103-11 (TNS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

47.INSPECT FRONT TURN SIGNAL LIGHT BULB SOCKET RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

59.CHECK HARNESS AND CONNECTOR (OUTER MIRROR RETRACTOR RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
J2-10 (B) - G195-13 (LR) Always Below 1 Ω
J2-11 (E) - Body ground Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
J2-10 (B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

34.INSPECT SIDE TURN SIGNAL LIGHT ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

60.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH - COMBINATION METER ASSEMBLY AND BODY GROUND)
a.

Disconnect the G195 combination meter assembly connector.


b.

Disconnect the A103 No. 1 headlight ECU sub-assembly RH connector.


c.

Disconnect the J2 outer mirror retractor RH connector.


d.

Disconnect the Q31*1 or R21*2 rear combination light socket and wire sub-assembly RH connector.

*1: for 3 Door

*2: for 5 Door



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - G195-13 (LR)*1 Always Below 1 Ω
R21-3 (TRN) - G195-13 (LR)*2 Always Below 1 Ω
Q31-4 (E) - Body ground*1 Always Below 1 Ω
R21-4 (E) - Body ground*2 Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition

*1: for 3 Door

*2: for 5 Door

Q31-3 (TRN) - Body ground*1 Always 10 kΩ or higher
R21-3 (TRN) - Body ground*2 Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

23.INSPECT REAR COMBINATION LIGHT SOCKET AND WIRE SUB-ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR