Home › Vehicle Interior › SEAT › FRONT SEAT ASSEMBLY (for Manual Seat) › from 2021.06
RM27T0E _58 Vehicle Interior _053737 SEAT _0261114 FRONT SEAT ASSEMBLY(for Manual Seat) A

SEAT  FRONT SEAT ASSEMBLY(for Manual Seat)  REASSEMBLY  


CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1.INSTALL FRONT SEAT SIDE AIRBAG ASSEMBLY (w/ Front Seat Side Airbag)

Hide 82168 2.INSTALL NO. 2 SEAT WIRE (for Driver Side)

a.

Attach the 2 clamps to install the seat wire.


b.

Connect the connector.


Hide 71552S 3.INSTALL SEPARATE TYPE FRONT SEATBACK PAD

a.

Install the seatback pad.


Hide 87510N 4.INSTALL FRONT SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71074S 5.INSTALL SEPARATE TYPE FRONT SEATBACK COVER

a.

Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.



HINT:

The number of hog rings differs according to seat type.


B242231C02
6.531,0.219 6.458,0.219 false 6.458,0.219 6.135,1.25 false 0.354,0.146 0.76,0.458 0.406,0.313 12 false *A 2.563,0.146 3.219,0.531 0.656,0.385 12 false *B 6.563,0.146 6.792,0.344 0.229,0.198 10 false *a
*A for Type A *B for Type B
*a Hog Ring Pliers - -



b.

Attach the 4 claws to install the 2 headrest supports.


c.

w/ Front Seat Side Airbag:

i.

Connect the seatback cover bracket to the seatback pad.

B617503C02
0.594,0.24 0.969,0.479 0.375,0.24 12 false *A 3.958,0.25 4.333,0.49 0.375,0.24 12 false *B
*A for Type A *B for Type B



ii.

Install the seatback cover bracket to the seat frame with the nut.

Torque:
5.5 N*m (56 kgf*cm, 49 in.*lbf)

NOTICE:

After the seatback trim cover is assembled, make sure the side airbag strap is not twisted.




d.

Close the 2 fasteners, and then close the seatback cover.

B242233C06
0.875,0.052 1.333,0.385 0.458,0.333 12 false *A 4.281,0.052 4.75,0.5 0.469,0.448 12 false *B
*A for Cloth Seat *B for Leather Seat



e.
B239193C04
2.354,0.177 2.188,0.177 2.188,0.177 1.688,1.573 false 2.396,0.104 2.625,0.302 0.229,0.198 10 false *a
*a Hog Ring Pliers


Using hog ring pliers, install 3 new hog rings.


Hide 71876A 6.INSTALL RECLINING ADJUSTER INSIDE COVER LH

B239257

a.

Move the cover in the direction of the arrow to install the cover.


b.

Attach the guide.


Hide 71875A 7.INSTALL RECLINING ADJUSTER INSIDE COVER RH

HINT:

Use the same procedure described for the LH side.


Hide 82192 8.INSTALL FRONT SEAT WIRE LH

a.

Install the seat wire.


Hide 87501B 9.INSTALL SEAT HEATER CONTROL SUB-ASSEMBLY LH (w/ Seat Heater System)

Hide 71537D 10.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR LH

B239189

a.

Move the protector in the direction of the arrow to attach the hook and install the protector.


b.

Install the screw.


Hide 71537C 11.INSTALL FRONT SEAT CUSHION EDGE PROTECTOR RH

HINT:

Use the same procedure described for the LH side.


Hide 71874 12.INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

a.

Attach the hook and clip to install the cushion shield.


b.

Install the screw.


Hide 71873 13.INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

a.

Attach the hook and clip to install the cushion shield.


b.

Install the screw.


Hide 71876 14.INSTALL RECLINING ADJUSTER INSIDE COVER LH

a.

Attach the claw and guide to install the cover.


Hide 87510L 15.INSTALL FRONT SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

Hide 71072S 16.INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

B239183C06
2.333,0.292 2.177,0.292 2.177,0.292 1.677,1.688 false 2.385,0.208 2.615,0.406 0.229,0.198 10 false *a
*a Hog Ring Pliers


a.

Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

NOTICE:
·

Be careful not to damage the cover.

·

When installing the hog rings, avoid wrinkling the cover.




b.
B372265C05
2.01,2.479 1.875,2.479 1.875,2.479 1.833,2.833 false 2.052,2.396 2.26,2.594 0.208,0.198 10 false *a
*a Hog Ring Pliers


Type A:

i.

Using hog ring pliers, connect the straps with new hog rings.



c.
B372267C06
2.281,1.5 2.979,1.5 true 2.979,1.396 3.177,1.583 0.198,0.188 10 false *a
*a Tack Pin


Type B:

i.

Connect the straps with new tack pins.



Hide 17.INSTALL SEAT CUSHION COVER WITH PAD

a.

Install the seat cushion cover with pad.


b.

for Front Passenger Side:

Attach the claw to connect the connector.


c.

Attach the hooks.


d.

w/ Seat Heater System:

Connect the seat heater connector and attach the 3 wire harness clamps.


Hide 71149A 18.INSTALL FRONT SEAT LEG COVER LH

B239172

a.

Move the cover in the direction of the arrow to install the cover.


b.

Attach the 2 claws.


Hide 62476E 19.INSTALL CAP

a.

Install the 2 caps.


Hide 71440S 20.INSTALL SEPARATE TYPE FRONT SEATBACK ASSEMBLY

a.

Install the seatback assembly with the 4 bolts.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


b.

w/ Front Seat Side Airbag:

i.

Connect the airbag wire harness.


ii.

Attach the fastening tape to close the cover.


iii.

Attach the hook and 3 airbag wire harness clamps.


iv.

Attach the claw and connect the airbag connector.



c.

for Clip Type:

Install the 2 clips.


d.

for Hook Type:

Attach the 2 hooks.


e.

w/ Seat Heater System:

Connect the seat heater connector and attach the wire harness clamp.


f.

for Driver Side:

Attach the clamp to connect the No. 2 seat wire.


g.

Install the rubber band to the seat cushion spring.


Hide 73240 21.INSTALL FRONT SEAT INNER BELT ASSEMBLY LH

Hide 71862 22.INSTALL FRONT SEAT INNER CUSHION SHIELD LH

B239168

a.

Attach the 3 claws to install the cushion shield.


Hide 71861 23.INSTALL FRONT SEAT INNER CUSHION SHIELD RH (for Front Passenger Side)

a.

Attach the 4 claws to install the cushion shield.


Hide 84920 24.INSTALL LUMBAR SWITCH ASSEMBLY (for Driver Side)

Hide 71812D 25.INSTALL FRONT SEAT CUSHION SHIELD LH

a.

for Driver Side:

Attach the 5 wire harness clamps and connect the 2 connectors.


b.
B239164

Attach the 4 claws and clip to install the cushion shield.


c.

Install the screw.


Hide 72495 26.INSTALL VERTICAL ADJUSTING HANDLE LH (for Driver Side)

a.

Install the handle with the screw.


Hide 72526 27.INSTALL RECLINING ADJUSTER RELEASE HANDLE LH

B238106

a.

Attach the claw to install the handle.