Cruise Control Switch Circuit
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The cruise control main switch is used to operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCELERATION), TAP-UP, and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCELERATION) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in each arrow direction and turns off after releasing it. The internal contact point of the cruise control main switch is turned on with the switch operation. Then the ECM reads the resistance value that has been changed by the switch operation to control SET, - (COAST), RES (RESUME), + (ACCELERATION) and CANCEL.WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (CRUISE CONTROL MAIN SWITCH) |
![]() ![]() |
Using the intelligent tester, read the Data List.
Cruise Control Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
CCS Main SW M-CPU
Cruise control main switch (Main CPU) / ON or OFF
ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch
CANCEL switch signal / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch signal / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch signal / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
CCS Main SW S-CPU
Cruise control main switch (Sub CPU) / ON or OFF
ON: Cruise control main switch (Sub CPU) on
OFF: Cruise control main switch (Sub CPU) off
-
- OK:
- The intelligent tester display changes according to operation of cruise control main switch.
|
|
||||
| OK | ||
| ||
| 2. INSPECT CRUISE CONTROL MAIN SWITCH |


Remove the cruise control main switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
1 - 3
Neutral
10 kΩ or higher
Pushed to +RES
216 to 264 Ω
Pushed to -SET
567 to 693 Ω
Pushed to CANCEL
1386 to 1694 Ω
Main switch pushed off
10 kΩ or higher
Main switch pushed on
Below 1 Ω
|
|
||||
| OK | |
| 3. INSPECT CRUISE CONTROL SWITCH WIRE |
![]() ![]() |
Remove the cruise control switch wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - 3
Always
Below 1 Ω
z37-4 - 1
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE |
![]() ![]() |
If there are any defects as follows, replace the spiral cable with a new one: scratches, cracks, dents or chips on the connector or the spiral cable.
Check spiral cable.
Set the spiral cable to the center position (Click here).
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise, and measure the resistance according to the value(s) in the table below. Then rotate the spiral cable 5 times counterclockwise, and measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - E12-1 (CCS)
Always
Below 1 Ω
z37-4 - E12-2 (ECC)
After setting the spiral cable to the center position, rotate the spiral cable 2.5 times clockwise. Then while rotating the spiral cable 5 times counterclockwise, measure the resistance according to the value(s) in the table below.
- NOTICE:
- As the spiral cable may break, do not rotate the spiral cable more than the specified amount.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
z37-3 - E12-1 (CCS)
Always
Below 1 Ω
z37-4 - E12-2 (ECC)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - ECM AND BODY GROUND) |
![]() ![]() |
Disconnect the E12 spiral cable connector.
Disconnect the A38*1 or A52*2 ECM connector.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for 2UZ-FE LHD, 3UR-FE LHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A38-45 (CCS)
Always
Below 1 Ω
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-2 (ECC) - Body ground
Always
Below 1 Ω
for 2UZ-FE RHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A52-45 (CCS)
Always
Below 1 Ω
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-2 (ECC) - Body ground
Always
Below 1 Ω
for 1GR-FE LHD, 1VD-FTV LHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A38-40 (CCS)
Always
Below 1 Ω
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-2 (ECC) - Body ground
Always
Below 1 Ω
for 1GR-FE RHD, 1VD-FTV RHD Tester Connection
Condition
Specified Condition
E12-1 (CCS) - A52-40 (CCS)
Always
Below 1 Ω
E12-1 (CCS) - Body ground
Always
10 kΩ or higher
E12-2 (ECC) - Body ground
Always
Below 1 Ω
Result Result
Proceed to
OK
(for 3UR-FE)
A
OK
(for 2UZ-FE)
B
OK
(for 1GR-FE)
C
OK
(for 1VD-FTV)
D
NG
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||




