2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the power window regulator switch, front power window regulator motor RH or harness or connector.

WIRING DIAGRAM

B184409E04

INSPECTION PROCEDURE


1. CHECK LIN COMMUNICATION SYSTEM
  1. Check for LIN communication system DTCs related to the power window control system (Click here).

    OK:
    LIN communication system DTCs are not output



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


2. CHECK FOR DTC (B2312)
  1. Check if DTC B2312 is output (Click here).

    OK:
    DTC B2312 is not output.



NG
GO TO DTC B2312 (Click here)
OK


3. READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Up SW
    Front passenger side power window manual up signal / ON or OFF
    ON: Front passenger side power window manual up switch operated
    OFF: Front passenger side power window switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down signal / ON or OFF
    ON: Front passenger side power window manual down switch operated
    OFF: Front passenger side power window switch not operated
    -

    OK:
    The display changes according to operation of the power window regulator switch.

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A


4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND)

  1. B184452E04
    Disconnect the I3*1 or I25*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I3-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I25-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND)
B180291E07
  1. Disconnect the I4*1 or I12*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I4-2 (B) - Body ground
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I12-2 (B) - Body ground
    Always
    11 to 14 V


    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I4-1 (GND) - Body ground
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I12-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR)

  1. B184455E09
    Disconnect the I3*1 or I25*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Disconnect the I4*1 or I12*2 motor connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    I3-6 (UP) - I4-10 (UP)
    Always
    Below 1 Ω
    I3-7 (DOWN) - I4-7 (DOWN)
    Always
    Below 1 Ω
    I3-8 (AUTO) - I4-4 (AUTO)
    Always
    Below 1 Ω
    I3-6 (UP) or I4-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I3-7 (DOWN) or I4-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I3-8 (AUTO) or I4-4 (AUTO) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    I25-6 (UP) - I12-10 (UP)
    Always
    Below 1 Ω
    I25-7 (DOWN) - I12-7 (DOWN)
    Always
    Below 1 Ω
    I25-8 (AUTO) - I12-4 (AUTO)
    Always
    Below 1 Ω
    I25-6 (UP) or I12-10 (UP) - Body ground
    Always
    10 kΩ or higher
    I25-7 (DOWN) or I12-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    I25-8 (AUTO) or I12-4 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH ASSEMBLY
B184456E16
  1. Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I3-6 (UP) - I3-1 (GND)
    Manual up operation
    Below 1 Ω
    I3-7 (DOWN) - I3-1 (GND)
    Manual down operation
    Below 1 Ω
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    I25-6 (UP) - I11-1 (GND)
    Manual up operation
    Below 1 Ω
    I25-7 (DOWN) - I11-1 (GND)
    Manual down operation
    Below 1 Ω

    Result 
    Result
    Proceed to
    NG
    A
    OK (for LHD)
    B
    OK (for RHD)
    C



B
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)

C
REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
A

REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)


← Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch (Sep 2011 – Dec 2011)Rear Power Window LH does not Operate with Rear Power Window Switch LH (Sep 2011 – Dec 2011) →