Front Passenger Side Power Window does not Operate with Front Passenger Side Power Window Switch
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- If the manual up/down function does not operate, there may be a malfunction in the power window regulator switch, front power window regulator motor RH or harness or connector.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK LIN COMMUNICATION SYSTEM |
Check for LIN communication system DTCs related to the power window control system (Click here).
- OK:
- LIN communication system DTCs are not output
|
|
||||
| OK | |
| 2. CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
- OK:
- DTC B2312 is not output.
|
|
||||
| OK | |
| 3. READ VALUE USING INTELLIGENT TESTER (FRONT PASSENGER SIDE POWER WINDOW REGULATOR MOTOR) |
Use the Data List to check if the power window regulator motor is functioning properly (Click here).
P-Door Motor Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
P Door P/W Up SW
Front passenger side power window manual up signal / ON or OFF
ON: Front passenger side power window manual up switch operated
OFF: Front passenger side power window switch not operated
-
P Door P/W Down SW
Front passenger side power window manual down signal / ON or OFF
ON: Front passenger side power window manual down switch operated
OFF: Front passenger side power window switch not operated
-
- OK:
- The display changes according to operation of the power window regulator switch.
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - BODY GROUND) |
Disconnect the I3*1 or I25*2 switch connector.

- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I3-1 (GND) - Body ground
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
I25-1 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (FRONT POWER WINDOW REGULATOR MOTOR - BATTERY AND BODY GROUND) |
![]() ![]() |
Disconnect the I4*1 or I12*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the voltage and resistance according to the value(s) in the table below.
- Standard Voltage:
for LHD Tester Connection
Condition
Specified Condition
I4-2 (B) - Body ground
Always
11 to 14 V
for RHD Tester Connection
Condition
Specified Condition
I12-2 (B) - Body ground
Always
11 to 14 V
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I4-1 (GND) - Body ground
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
I12-1 (GND) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH - FRONT POWER WINDOW REGULATOR MOTOR) |
Disconnect the I3*1 or I25*2 switch connector.

- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Disconnect the I4*1 or I12*2 motor connector.
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Condition
Specified Condition
I3-6 (UP) - I4-10 (UP)
Always
Below 1 Ω
I3-7 (DOWN) - I4-7 (DOWN)
Always
Below 1 Ω
I3-8 (AUTO) - I4-4 (AUTO)
Always
Below 1 Ω
I3-6 (UP) or I4-10 (UP) - Body ground
Always
10 kΩ or higher
I3-7 (DOWN) or I4-7 (DOWN) - Body ground
Always
10 kΩ or higher
I3-8 (AUTO) or I4-4 (AUTO) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
I25-6 (UP) - I12-10 (UP)
Always
Below 1 Ω
I25-7 (DOWN) - I12-7 (DOWN)
Always
Below 1 Ω
I25-8 (AUTO) - I12-4 (AUTO)
Always
Below 1 Ω
I25-6 (UP) or I12-10 (UP) - Body ground
Always
10 kΩ or higher
I25-7 (DOWN) or I12-7 (DOWN) - Body ground
Always
10 kΩ or higher
I25-8 (AUTO) or I12-4 (AUTO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. INSPECT FRONT PASSENGER SIDE POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() ![]() |
Remove the power window regulator switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for LHD Tester Connection
Switch Condition
Specified Condition
I3-6 (UP) - I3-1 (GND)
Manual up operation
Below 1 Ω
I3-7 (DOWN) - I3-1 (GND)
Manual down operation
Below 1 Ω
for RHD Tester Connection
Switch Condition
Specified Condition
I25-6 (UP) - I11-1 (GND)
Manual up operation
Below 1 Ω
I25-7 (DOWN) - I11-1 (GND)
Manual down operation
Below 1 Ω
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||


