C1401 Front Speed Sensor RH Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- C1271 Low Output Signal of Front Speed Sensor RH (Test Mode DTC)
- C1272 Low Output Signal of Front Speed Sensor LH (Test Mode DTC)
- C1402 Front Speed Sensor LH Malfunction
DESCRIPTION
The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU (master cylinder solenoid). These signals are used for brake control.- HINT:
- When the connectors between the speed sensor and skid control ECU (master cylinder solenoid) are connected, the following waveform is output.


| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1401 C1402 |
One of the following conditions is met:
|
|
| C1271 C1272 |
Stored only during test mode. |
|
- HINT:
- DTCs C1401 and C1271 are for the front speed sensor RH.
- DTCs C1402 and C1272 are for the front speed sensor LH.
- DTCs C1401 and C1271 are for the front speed sensor RH.
INSPECTION PROCEDURE
- NOTICE:
- Check the speed sensor signal after cleaning or replacement (Click here).
| 1. CHECK FRONT SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
Check the speed sensor installation (Click here).

- OK:
- There is no clearance between the sensor and the front steering knuckle.
- The installation bolt is tightened properly.
Text in Illustration *1
Front Speed Sensor
*a
No clearance
*b
OK
*c
NG
|
|
||||
| OK | |
| 2. INSPECT FRONT SPEED SENSOR TIP |
Remove the front speed sensor (Click here).
Check the speed sensor tip.
- OK:
- No scratches, oil, or foreign matter on the sensor tip.
- NOTICE:
- If no damage to the speed sensor tip is found during this inspection, do not replace the speed sensor.
|
|
||||
| OK | |
| 3. INSPECT FRONT SPEED SENSOR ROTOR |
Remove the front axle hub sub-assembly (Click here).
Check the speed sensor rotor.
- OK:
- No scratches, oil, or foreign matter on the rotors.
- HINT:
- The front speed sensor rotor is incorporated into the front axle with ABS rotor bearing assembly.
- If the front speed sensor rotor needs to be replaced, replace it together with the front axle with ABS rotor bearing assembly.
|
|
||||
| OK | |
| 4. READ VALUE USING GTS (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | ||
| ||
| 5. REPLACE FRONT SPEED SENSOR |
Replace the front speed sensor (Click here).
| NEXT | |
| 6. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | ||
| ||
