C1405 Open or Short in Front Speed Sensor RH Circuit
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- C1406 Open or Short in Front Speed Sensor LH Circuit
DESCRIPTION
Refer to DTCs C1401 and C1402 (Click here).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1405 C1406 |
Either condition is met:
|
|
- HINT:
- DTC C1405 is for the front speed sensor RH.
- DTC C1406 is for the front speed sensor LH.
- DTC C1405 is for the front speed sensor RH.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the master cylinder solenoid, perform zero point calibration (Click here).
- Check the speed sensor signal after replacement (Click here).
- After replacing the master cylinder solenoid, perform zero point calibration (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the GTS, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Speed Open
Front speed sensor RH open detection/ Error or Normal
Normal
-
FL Speed Open
Front speed sensor LH open detection/ Error or Normal
Normal
-
- OK:
- Normal (there are no momentary interruptions).
- HINT:
- Perform the above inspection before removing the sensor and connector.
|
|
||||
| OK | |
| 2. READ VALUE USING GTS (FR/FL WHEEL SPEED) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
FR Wheel Speed
Front speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
FL Wheel Speed
Front speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph)
Actual wheel speed
No large fluctuations when driving at a constant speed.
Check that there is no difference between the speed value output from the speed sensor displayed on the GTS and the speed value displayed on the speedometer when driving the vehicle.
- HINT:
- Factors that affect the indicated vehicle speed include tire size, tire inflation and tire wear. The speed indicated on the speedometer has an allowable margin of error. This can be tested using a speedometer tester (calibrated chassis dynamometer). For details about testing and the margin of error, refer to the reference chart (Click here).
- OK:
- The speed value output from the speed sensor displayed on the GTS is the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).
|
|
||||
| OK | |
| 3. RECONFIRM DTC |
Clear the DTC (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. INSPECT SKID CONTROL SENSOR WIRE |
Remove the skid control sensor wire (Click here).
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
Az2-1 - z17-1 (FR-)
Always
Below 1 Ω
Az2-5 - z17-2 (FR+)
Always
Below 1 Ω
z17-1 (FR-) - z17-2 (FR+)
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
Az1-1 - z18-1 (FL-)
Always
Below 1 Ω
Az1-5 - z18-2 (FL+)
Always
Below 1 Ω
z18-1 (FL-) - z18-2 (FL+)
Always
10 kΩ or higher
Text in Illustration *A
for RH
*B
for LH
*1
Skid Control Sensor Wire
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - FRONT SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Disconnect the z17 and/or z18 speed sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RH Tester Connection
Condition
Specified Condition
A24-3 (FR+) - z17-2 (FR+)
Always
Below 1 Ω
A24-3 (FR+) - Body ground
Always
10 kΩ or higher
A24-17 (FR-) - z17-1 (FR-)
Always
Below 1 Ω
A24-17 (FR-) - Body ground
Always
10 kΩ or higher
for LH Tester Connection
Condition
Specified Condition
A24-18 (FL+) - z18-2 (FL+)
Always
Below 1 Ω
A24-18 (FL+) - Body ground
Always
10 kΩ or higher
A24-4 (FL-) - z18-1 (FL-)
Always
Below 1 Ω
A24-4 (FL-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (FR+/FL+ TERMINAL) |
Disconnect the speed sensor connector.
Connect the A24 skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
for RH Tester Connection
Switch Condition
Specified Condition
z17-2 (FR+) - Body ground
Ignition switch ON
11 to 14 V
for LH Tester Connection
Switch Condition
Specified Condition
z18-2 (FL+) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *A
for RH
*B
for LH
*a
Front view of wire harness connector
(to Front Speed Sensor)
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
