2011-2013 Land Cruiser · Service Manual Brake

INSTALLATION

Removal / installation · Vehicles built from Sep 2011

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 2 parking brake cable clamp.

  1. Install the No. 2 parking brake cable with the 6 bolts.

    C170911E01

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. Install the fuel tank (Click here).

  1. C172839
    Attach the claws of the No. 2 parking brake cable.

  1. C226757
    Connect the No. 2 parking brake cable to the No. 1 parking brake pull rod.


2. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY
  1. Install the No. 3 parking brake cable clamp.

  1. Install the No. 3 parking brake cable with the 6 bolts.

    C170910E01

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

  1. C170907
    Attach the claws of the No. 3 parking brake cable.

  1. C226757
    Connect the No. 3 parking brake cable to the No. 1 parking brake pull rod.


3. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C170909
    Connect the No. 3 parking brake cable with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


4. INSTALL PARKING BRAKE SHOE LEVER LH

  1. C177128E01
    Apply high temperature grease to the parking brake anchor block.

  1. Install the parking brake shoe lever to the No. 3 parking brake cable.

    NOTICE:
    Be carefully to distinguish between the parking brake shoe lever RH and LH.


5. INSTALL NO. 2 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.

  1. C172175E01
    Using SST, install the No. 2 parking brake shoe with the shoe hold down spring pin, compression spring and shoe hold down spring cup.
    SST
    09718-00011  


6. INSTALL NO. 1 PARKING BRAKE SHOE ASSEMBLY LH
  1. Apply high temperature grease to the areas of the backing plate that contact the shoe.

  1. C172178E01
    Apply high temperature grease to the thread and all joining areas of the parking brake shoe adjuster screw set.

  1. C172179
    Set the No. 1 parking brake shoe and shoe adjuster screw set in place.

  1. C172180
    Connect the tension spring.

  1. C172174E01
    Using SST, install the shoe hold down spring pin, compression spring and shoe hold down spring cup.
    SST
    09718-00011  


7. INSTALL PARKING BRAKE SHOE RETURN SPRING

  1. C172171E01
    Using SST, install the shoe return spring.
    SST
    09703-30011  


8. CHECK PARKING BRAKE INSTALLATION

  1. Check that each part is installed properly.

    C172182E01


9. INSTALL REAR DISC

  1. C172168E01
    Align the matchmarks, and then install the rear disc.

    HINT:
    When replacing the rear disc with a new one, select the installation position where the rear disc has the minimum runout.


10. CONNECT REAR DISC BRAKE CYLINDER ASSEMBLY LH

  1. C172183
    Connect the rear disc brake cylinder with 2 new bolts.

    Torque:
    95 N*m{ 969 kgf*cm , 70 ft.*lbf }

    NOTICE:
    1. Do not twist the brake hose.
    2. Make sure that the bolts are free from damage and foreign matter.
    3. Do not overtighten the bolts.


11. INSTALL REAR NO. 2 SUSPENSION CONTROL ACCUMULATOR BRACKET
  1. Install the bracket to the shock absorber control valve with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


12. INSTALL HEIGHT CONTROL UNIT PROTECTOR PIPE

  1. Install the protector pipe with the 6 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


    C179788


13. ADJUST PARKING BRAKE
(Click here)

14. INSTALL REAR WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }


15. INSTALL LOWER CONSOLE BOX (w/o Console Box Lid)
(Click here)

16. INSTALL COOLING BOX ASSEMBLY (w/ Cool Box)
(Click here)

17. INSTALL REAR CONSOLE BOX SUB-ASSEMBLY (w/o Cool Box)
(Click here)
← REMOVAL (from Sep 2011)COMPONENTS (from Sep 2011) →