Illumination Circuit
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
Power is supplied to the multi-media module receiver assembly, multi-display assembly and steering pad switch assembly illumination when the light control switch is in the tail or head position.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
- Inspect the fuse for circuits related to this system before performing the following inspection procedure.
- The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).
| 1. CHECK ILLUMINATION |
Check if the illumination for the multi-media module receiver assembly, multi-display assembly, steering pad switch assembly or others (hazard switch etc.) comes on when the light control switch is turned to the head or tail position.
Result Result
Proceed to
Illumination comes on for all components except steering pad switch assembly.
A
Illumination comes on for all components except multi-display assembly.
B
Illumination comes on for all components except multi-media module receiver assembly.
C
No illumination comes on (multi-media module receiver assembly, steering pad switch, hazard switch, heater control switch, etc.).
D
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK HARNESS AND CONNECTOR (ILLUMINATION SIGNAL) |
Disconnect the spiral cable sub-assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
E12-12 (IL+2) - Body ground
Light control switch in the tail or head position
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Spiral Cable Sub-assembly)
|
|
||||
| OK | |
| 3. INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).
Inspect the steering pad switch assembly (Click here).
|
|
||||
| OK | |
| 4. INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Remove the spiral cable sub-assembly (Click here).
Inspect the spiral cable sub-assembly (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY, MULTI-DISPLAY ASSEMBLY - SPIRAL CABLE SUB-ASSEMBLY) |
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the F79 multi-display assembly connector.
Disconnect the E12 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F77-14 (ILL+) - E12-12 (IL+2)
Always
Below 1 Ω
F77-32 (SWG) - E12-4 (EAU)
Always
Below 1 Ω
F79-2 (ILL) - E12-12 (IL+2)
Always
Below 1 Ω
F77-14 (ILL+) - Body ground
Always
10 kΩ or higher
F77-32 (SWG) - Body ground
Always
10 kΩ or higher
F79-2 (ILL) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (MULTI-DISPLAY ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the multi-display assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F79-14 (ILL-) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F79-2 (ILL) - Body ground
Light control switch in the tail or head position
11 to 14 V
| *a |
Front view of wire harness connector (to Multi-display Assembly) |
|
|
||||
| OK | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - BATTERY AND BODY GROUND) |
Disconnect the multi-media module receiver assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F77-14 (ILL+) - Body ground
Light control switch in the tail or head position
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F77-13 (ILL-) - Body ground
Always
Below 1 Ω
| *a |
Front view of wire harness connector (to Multi-media Module Receiver Assembly) |
|
|
||||
| OK | ||
| ||
