2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

CAUTION / NOTICE / HINT


DESCRIPTION

Refer to DTC P2195 (Click here).
DTC Code
DTC Detection Condition
Trouble Area
P2A00
The calculated value of the air-fuel ratio (A/F) sensor response rate deterioration level is less than the threshold (2 trip detection logic).
  1. Open or short in A/F sensor circuit (for bank 1)
  2. A/F sensor (for bank 1)
  3. ECM
P2A03
The calculated value of the air-fuel ratio (A/F) sensor response rate deterioration level is less than the threshold (2 trip detection logic).
  1. Open or short in A/F sensor circuit (for bank 2)
  2. A/F sensor (for bank 2)
  3. ECM

MONITOR DESCRIPTION

After the engine is warmed up, the ECM performs air-fuel ratio feedback control to maintain the air-fuel ratio at the stoichiometric level. In addition, active A/F control is performed for approximately 10 seconds after the preconditions are met in order to measure the A/F sensor response rate. During active A/F control, the ECM forcibly increases and decreases the injection volume a certain amount, based on the stoichiometric air-fuel ratio learned during normal air-fuel ratio control, and measures the A/F sensor response rate. The ECM receives a signal from the A/F sensor while performing active A/F control and uses it to calculate the A/F sensor response rate deterioration level.
If the A/F sensor response rate deterioration level is less than the threshold, the ECM interprets this as a malfunction and stores the DTC.
A115363E09

CONFIRMATION DRIVING PATTERN

HINT:
Performing this confirmation pattern will activate the A/F sensor response monitor.

A169852E04
  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Turn the engine switch on (IG).
  3. (c) Turn the tester on.
  4. (d) Clear the DTCs.
  5. (e) Start the engine.
  6. (f) Enter the following menus: Powertrain / Engine and ECT / Data List / Monitor Status.
  7. (g) Check that O2S (A/FS) Monitor is Incmpl.
  8. (h) Warm up the engine.
  9. (i) Drive the vehicle at between 60 km/h and 120 km/h (38 mph and 75 mph) for 5 minutes. However, the vehicle should be driven at a constant speed.
  10. (j) Check that O2S (A/FS) Monitor is Incmpl.
  11. (k) Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.
  12. (l) Check if any DTCs (any pending DTCs) are output.

WIRING DIAGRAM

Refer to DTC P2195 (Click here).

INSPECTION PROCEDURE

HINT:
Malfunctioning areas can be identified by performing the Control the Injection Volume for A/F sensor function provided in the Active Test. The Control the Injection Volume for A/F sensor function can help to determine whether the Air-Fuel Ratio (A/F) sensor, Heated Oxygen (HO2) sensor and other potential trouble areas are malfunctioning.
The following instructions describe how to conduct the Control the Injection Volume for A/ F sensor operation using the intelligent tester.

  1. (a) Connect the intelligent tester to the DLC3.
  2. (b) Start the engine and turn the tester on.
  3. (c) Warm up the engine at an engine speed of 2500 rpm for approximately 90 seconds.
  4. (d) Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/ F sensor.
  5. (e) Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).
  6. (f) Monitor the output voltages of the A/F and HO2 sensors (AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2) displayed on the tester.

    HINT:
    1. The Control the Injection Volume for A/F sensor operation lowers the fuel injection volume by 12.5% or increases the injection volume by 25%.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.

      Standard:
      Tester Display
      (Sensor)
      Injection Volume
      Status
      Voltage
      AFS B1 S1
      (A/F)
      +25%
      Rich
      Below 3.0
      -12.5%
      Lean
      Higher than 3.35
      O2S B1 S2
      (HO2)
      +25%
      Rich
      Higher than 0.55
      -12.5%
      Lean
      Below 0.4
      AFS B2 S1
      (A/F)
      +25%
      Rich
      Below 3.0
      -12.5%
      Lean
      Higher than 3.35
      O2S B2 S2
      (HO2)
      +25%
      Rich
      Higher than 0.55
      -12.5%
      Lean
      Below 0.4

NOTICE:
The A/F sensor has an output delay of a few seconds and the HO2 sensor has a maximum output delay of approximately 20 seconds.

Case
A/F Sensor (Sensor 1) Output Voltage
HO2 Sensor (Sensor 2) Output Voltage
Main Suspected Trouble Area
1
A150787E01
A151324E02
A150787E01
A150788E04
-
2
A150787E01
A150790E01
A150787E01
A150788E04
  1. A/F sensor
  2. A/F sensor heater
  3. A/F sensor circuit
3
A150787E01
A151324E02
A150787E01
A150790E01
  1. HO2 sensor
  2. HO2 sensor heater
  3. HO2 sensor circuit
4
A150787E01
A150790E01
A150787E01
A150790E01
  1. Injector
  2. Fuel pressure
  3. Gas leakage from exhaust system (Air-fuel ratio extremely rich or lean)
  1. Following the Control the Injection Volume for A/F Sensor procedure enables technicians to check and graph the voltage outputs of both the A/F and HO2 sensors.
  2. To display the graph, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/ F Sensor / A/F Control System / AFS B1 S1 and O2S B1 S2 or AFS B2 S1 and O2S B2 S2.

HINT:
  1. Sensor 1 refers to the sensor mounted in front of the Three-Way Catalytic Converter (TWC) and located near the engine assembly.
  2. DTC P2A00 indicates malfunctions related to the bank 1 A/F sensor.
  3. DTC P2A03 indicates malfunctions related to the bank 2 A/F sensor.
  4. For Bank 1 refers to the bank that includes the No. 1 cylinder.
  5. For Bank 2 refers to the bank that includes the No. 2 cylinder.
  6. DTC P2A00 or P2A03 may be stored when the air-fuel ratio is stuck rich or lean.
  7. A low A/F sensor voltage could be caused by a rich air-fuel mixture. Check for conditions that would cause the engine to run rich.
  8. A high A/F sensor voltage could be caused by a lean air-fuel mixture. Check for conditions that would cause the engine to run lean.
  9. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    P2A00 and/or P2A03 is output
    A
    P2A00 and/or P2A03 and other DTCs are output
    B

    HINT:
    If any DTCs relating to the A/F sensor (DTCs for the A/F sensor heater or A/F sensor admittance) are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2. INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE)
A150241E06
  1. Disconnect the Air-Fuel Ratio (A/F) sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (HA1A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA1A) - 4 (A1A-)
    Always
    10 kΩ or higher
    1 (HA2A) - 2 (+B)
    20°C (68°F)
    1.8 to 3.4 Ω
    1 (HA2A) - 4 (A2A-)
    Always
    10 kΩ or higher



NG
REPLACE AIR FUEL RATIO SENSOR (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ECM - AIR-FUEL RATIO SENSOR)
A182483E02
  1. Disconnect the A/F sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C22-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V
    C23-2 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V

  1. Turn the engine switch off.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C45-22 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C45-126 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C45-125 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C45-20 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C45-103 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C45-102 (A2A-)
    Always
    Below 1 Ω
    C22-1 (HA1A) or C45-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C45-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C45-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C45-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C45-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C45-102 (A2A-) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C22-1 (HA1A) - C46-22 (HA1A)
    Always
    Below 1 Ω
    C22-3 (A1A+) - C46-126 (A1A+)
    Always
    Below 1 Ω
    C22-4 (A1A-) - C46-125 (A1A-)
    Always
    Below 1 Ω
    C23-1 (HA2A) - C46-20 (HA2A)
    Always
    Below 1 Ω
    C23-3 (A2A+) - C46-103 (A2A+)
    Always
    Below 1 Ω
    C23-4 (A2A-) - C46-102 (A2A-)
    Always
    Below 1 Ω
    C22-1 (HA1A) or C46-22 (HA1A) - Body ground
    Always
    10 kΩ or higher
    C22-3 (A1A+) or C46-126 (A1A+) - Body ground
    Always
    10 kΩ or higher
    C22-4 (A1A-) or C46-125 (A1A-) - Body ground
    Always
    10 kΩ or higher
    C23-1 (HA2A) or C46-20 (HA2A) - Body ground
    Always
    10 kΩ or higher
    C23-3 (A2A+) or C46-103 (A2A+) - Body ground
    Always
    10 kΩ or higher
    C23-4 (A2A-) or C46-102 (A2A-) - Body ground
    Always
    10 kΩ or higher

    A164715E01



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


5. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    P2A00 and/or P2A03 is output
    A
    No DTC is output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


6. REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).


NEXT


7. PERFORM CONFIRMATION DRIVING PATTERN

NEXT


8. CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC / Pending.

  1. Read pending DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P2A00 and/or P2A03 is output
    B



B
REPLACE ECM (Click here)
A

END


← P2444 Secondary Air Injection System Pump Stuck On Bank1 (+ P2445) (Sep 2011 – Dec 2011)U0101 Lost Communication with TCM (Sep 2011 – Dec 2011) →