2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P2444 Secondary Air Injection System Pump Stuck On Bank1

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The diagnostic trouble code (DTC) indicates that the air pump of the secondary air injection (AIR) system malfunctions. The engine control module (ECM) operates entire components of this system in a sequence, and monitors the system pressure and exhaust pulse (AIR monitor). This monitor will run just after a cold engine start. If abnormal pressure and exhaust pulse are detected, the ECM interprets this as a malfunction. When the malfunction is detected in consecutive driving cycle, the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.
A182943E01
Reference 1: Operation of each component during AIR monitor
A182941E01
Reference 2: DTC Storing Conditions 
Time A
[Pressure Change]
Time B
[Pressure Change]
Time C
[See Chart Below]
Time D
[Exhaust Pulse]
Time E
[Exhaust Pulse]
Time F
[See Chart Below]
DTC
Yes
Yes
Pattern 1
-
No
Pattern 4
Normal
Yes
No
Pattern 1
Yes
No
Pattern 4
Yes
Yes
Pattern 1
-
No
Pattern 1
P1441
P1444
P2444
No
Yes
Pattern 1
-
No
Pattern 1
Yes
No
Pattern 1
Yes
No
Pattern 1
No
No
Pattern 1
Yes
No
Pattern 1
Yes
Yes
Pattern 1
-
No
Pattern 3
P2444
No
Yes
Pattern 1
-
No
Pattern 3
P1442
P1445
P2444
Yes
No
Pattern 1
No
No
Pattern 3
No
No
Pattern 1
No
No
Pattern 3
P1442
P1444
P2444
No
No
Pattern 2
-
-
-
P2445
No
No
Pattern 4
-
-
-
P1442
P1445
P2441
P2444
No
No
Pattern 3
No
No
Pattern 3
Reference 3: System Pressure and Exhaust Pulse 
Pattern
System Pressure
Exhaust Pulse
1
High
Yes
2
Low
Yes
3
High
No
4
Low
No
DTC Code 
DTC Code
DTC Detection Condition
Trouble Area
P2444
The air pump is stuck on (2 trip detection logic).
  1. Air pump
  2. Pressure sensor
P2445
- The air pump is stuck off (2 trip detection logic).
- The air injection amount is insufficient (2 trip detection logic).
  1. Air pump
  2. Pressure sensor
  3. Air injection system piping
  4. Pressure sensor

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM SECONDARY AIR INJECTION SYSTEM CHECK (AUTOMATIC MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Record the DTCs and freeze frame data.

  1. Clear the DTCs (Click here).

  1. Warm-up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Automatic Mode).

  1. Perform the Active Test and check the pending DTC.

    Result 
    Result
    Proceed to
    P2444 and P2445 is output
    A
    DTCs other than P2444 and P2445 are output
    B
    No DTC is output
    C



B
GO TO DTC CHART (Click here)

C
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. CHECK VACUUM HOSE
G032743E01
  1. Remove the intake manifold (Click here).

  1. Check the vacuum hose connection between the pressure sensor and air switching valve.

    OK:
    The vacuum hose is securely connected.

  1. Inspect the vacuum hose for blockage and damage.

    OK:
    The vacuum hose has no blockage or damage.



NG
REPAIR OR REPLACE VACUUM HOSE
OK


3. READ VALUE USING INTELLIGENT TESTER (AIR VOLTAGE)
G032742E01
  1. Remove the intake manifold (Click here).

  1. Connect the pressure gauge to the pressure sensor as shown in the illustration.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on (do not start the engine).

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure.

  1. When applying pressure by the hand pump, check that the air pump pressure is almost same as the pressure gauge indication.

    OK:
    Pressure fluctuates in response to the pressure applied with pressure gauge.



NG
REPLACE AIR PRESSURE SENSOR (Click here)
OK


4. CHECK HOSE AND PIPE
G032737E01
  1. Remove the intake manifold (Click here).

  1. Check that all the pipes and hoses between the air pump and air switching valve are securely connected.

    OK:
    All air injection pipes and hoses are securely connected.

  1. Check all pipes and hoses for blockages and damage.

    OK:
    All air injection pipes and hoses have no blockages or damage.



NG
REPAIR OR REPLACE HOSES AND TUBES (Click here)
OK

REPLACE AIR PUMP ASSEMBLY (Click here)


← P2431 Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1 (+ P2432, P2433) (Sep 2011 – Dec 2011)P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) (+ P2A03) (Sep 2011 – Dec 2011) →