2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P1613 Secondary Air Injection Driver Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The diagnostic trouble code (DTC) indicates an open or short in the air injection control driver circuit of the secondary air injection (AIR) system. The air injection control driver diagnoses the air pump circuit, E-ASV circuit and itself, and sends the diagnosis signal to the engine control module (ECM). If the ECM receives a malfunction signal from the air injection control driver, the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.
DTC Code
DTC Detection Condition
Trouble Area
P1613
The ECM receives a diagnostic signal from the driver (duty-cycle: 0%, 100% or other than 0, 20, 40, 60, 80, or 100%).
  1. Air injection control driver
  2. ECM
  3. Diagnostic signal circuit (Driver - ECM)

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK AIR INJECTION CONTROL DRIVER
A181313E01
  1. Inspection 1.

    1. Disconnect the air injection control driver connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      C61-5 (+B) - Body ground
      Engine switch on (IG)
      11 to 14 V

  1. Inspection 2.

    1. Disconnect the air injection control driver connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Switch Condition
      Specified Condition
      C60-1 (BATT) - Body ground
      Engine switch on (IG)
      11 to 14 V

  1. Inspection 3.

    1. Disconnect the air injection control driver connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      C61-1 (E) - Body ground
      Always
      Below 1 Ω

Result 
Result
Proceed to
OK
A
Inspection 1 NG
B
Inspection 2 NG
C
Inspection 3 NG
D


B
Go to step 4

C
Go to step 5

D
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


2. CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - ECM)
A182499E02
  1. Disconnect the ECM connector.

  1. Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C61-3 (SIV) - C45-28 (AIRV)
    Always
    Below 1 Ω
    C61-4 (SIP) - C45-54 (AIRP)
    Always
    Below 1 Ω
    C61-2 (DI) - C45-30 (AIDI)
    Always
    Below 1 Ω
    C61-3 (SIV) or C45-28 (AIRV) - Body ground
    Always
    10 kΩ or higher
    C61-4 (SIP) or C45-54 (AIRP) - Body ground
    Always
    10 kΩ or higher
    C61-2 (DI) or C45-30 (AIDI) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C61-3 (SIV) - C46-28 (AIRV)
    Always
    Below 1 Ω
    C61-4 (SIP) - C46-54 (AIRP)
    Always
    Below 1 Ω
    C61-2 (DI) - C46-30 (AIDI)
    Always
    Below 1 Ω
    C61-3 (SIV) or C46-28 (AIRV) - Body ground
    Always
    10 kΩ or higher
    C61-4 (SIP) or C46-54 (AIRP) - Body ground
    Always
    10 kΩ or higher
    C61-2 (DI) or C46-30 (AIDI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK ECM (AIDI VOLTAGE)
A182398E02
  1. Disconnect the air injection control driver connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C61-2 (DI) - Body ground
    Engine switch on (IG)
    11 to 14 V



OK
Go to step 6

NG
REPLACE ECM (Click here)
4. CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - EFI NO. 2 FUSE)
A181916E01
  1. Disconnect the air injection control driver connector.

  1. Remove the EFI NO. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C61-5 (+B) - EFI NO. 2 fuse (2)
    Always
    Below 1 Ω
    C61-5 (+B) or EFI NO. 2 fuse (2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECU POWER SOURCE CIRCUIT (Click here)

5. CHECK HARNESS OR CONNECTOR (BATTERY - A/PUMP FUSE)
  1. Remove the A/PUMP fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A/PUMP Fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - A/PUMP FUSE)

6. REPLACE AIR INJECTION CONTROL DRIVER
  1. Replace the air injection control driver (Click here).


NEXT


7. CHECK WHETHER DTC OUTPUT RECURS (DTC P1613)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Perform the Active Test to operate the air injection system.Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Automatic Mode).

  1. After operating the secondary air injection system, confirm the pending codes of the secondary air injection system by entering the following menus: Powertrain / Engine and ECT / DTC / Pending codes.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P1613 is output
    B

    NOTICE:
    1. When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.
    2. Turn the engine switch off when the Secondary Air Injection Check operation finishes.



B
REPLACE ECM (Click here)
A

END


← P1607 Cruise Control Input Processor (Sep 2011 – Dec 2011)P2102 Throttle Actuator Control Motor Circuit Low (+ P2103) (Sep 2011 – Dec 2011) →