2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

NOTICE:
Set to recirculation mode before removing the air conditioning filter.

  1. for Standard:
    (Click here)

  1. w/ Winch:
    (Click here)


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. for Standard:
    (Click here)

  1. w/ Winch:
    (Click here)


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. for 1VD-FTV:
    (Click here)

  1. for 2UZ-FE:
    (Click here)

  1. for 1GR-FE:
    (Click here)


4. REMOVE UPPER RADIATOR SUPPORT SEAL

  1. Remove the 7 clips and radiator support seal.

    B180890E02


5. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM
  1. Start the engine.

  1. Turn the A/C switch on.

  1. Operate the cooler compressor while the engine speed is approximately 1000 rpm for 5 to 6 minutes to circulate the refrigerant and collect the compressor oil remaining in each component into the cooler compressor.

  1. Stop the engine.

  1. Recover the refrigerant from the A/C system using a refrigerant recovery unit.


6. DRAIN ENGINE COOLANT
  1. for 1VD-FTV:
    (Click here)

  1. for 2UZ-FE:
    (Click here)

  1. for 1GR-FE:
    (Click here)


7. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


8. DISCONNECT AIR CONDITIONING TUBE ASSEMBLY

  1. E154197E02
    Remove the bolt.

  1. Detach the plate as shown in the illustration.

    Text in Illustration 
    *1
    Plate

  1. I043960E05
    Disconnect the air conditioning tube assembly.

    NOTICE:
    1. Do not use a screwdriver or similar tool to disconnect the tube.
    2. Seal the openings of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering them.

    Text in Illustration 
    *a
    Disconnect tube by hand

  1. Remove the 2 O-rings from the air conditioning tube assembly.


9. DISCONNECT HEATER WATER INLET HOSE AND HEATER WATER OUTLET HOSE

  1. E154268E04
    Using pliers, grip the claws of the clips and slide the 2 clips.

  1. Disconnect the 2 heater water hoses.

    Text in Illustration 
    *A
    for 1GR-FE
    *B
    for 2UZ-FE
    *C
    for 1VD-FTV


10. REMOVE FRONT WIPER MOTOR AND BRACKET
(Click here)

11. REMOVE INSTRUMENT PANEL SUB-ASSEMBLY
(Click here)

12. REMOVE NO. 3 AIR DUCT SUB-ASSEMBLY

E156902
  1. Remove the clip.

  1. Detach the 2 claws and remove the duct.


13. REMOVE STEERING COLUMN ASSEMBLY
  1. for Power Tilt and Power Telescopic Steering Column:
    (Click here)

  1. for Manual Tilt and Manual Telescopic Steering Column:
    (Click here)


14. REMOVE HEATER TO REGISTER DUCT ASSEMBLY
  1. Remove the 3 clips.

  1. Detach the 2 claws and remove the duct.

    E156935


15. REMOVE INSTRUMENT PANEL REINFORCEMENT ASSEMBLY
  1. Detach the 17 clamps and 2 claws and remove the 9 bolts and 5 nuts.

  1. Disconnect the connectors and wire harness.

    E155239

  1. Remove the instrument panel reinforcement.

    1. for Driver Side:
      Remove the 3 caps and 3 bolts.

    2. for Passenger Side:
      Remove the 2 caps.

    3. for Passenger Side:
      Using a T40 "TORX" socket, remove the 2 "TORX" bolts.

      HINT:
      When removing the bolts, the collars may come off with the bolts.

    4. for Passenger Side:
      Using a 12 mm hexagon wrench, remove the 2 collars.

    5. Remove the 7 bolts, screw and instrument panel reinforcement.

      E155490


16. REMOVE AIR CONDITIONING HOSE AND ACCESSORY (w/ Cool Box)

E154321
  1. Remove the bolt.

  1. Using SST, remove the piping clamp.

    SST
    09870-00025  

    1. E112919E02
      Attach SST to the piping clamp.

      HINT:
      Confirm the direction of the piping clamp claw and SST by referring to the illustration on the caution label.

    2. E112920E04
      Push down SST and release the clamp lock.

      NOTICE:
      Be careful not to deform the tubes when pushing SST.

      Text in Illustration 
      *1
      Release Lever
      *a
      Push
      *b
      Pull

    3. Pull SST slightly and push the release lever, then remove the piping clamp with SST.

    4. Remove the piping clamp from SST.

  1. Disconnect the hose and accessory from the liquid tube to remove it.

    NOTICE:
    Cap the open fittings immediately to keep moisture or dirt out of the system.

  1. Remove the 2 O-rings from the air conditioning hose and accessory.


17. REMOVE AIR CONDITIONING UNIT

  1. E156861
    Remove the 2 nuts and air conditioning unit.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →