2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P1441 Stuck Open in Secondary Air Injection Vacuum Switching Valve Bank 1

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The diagnostic trouble code (DTC) indicates that the electric air switching valve (E-ASV) and air switching valves (ASVs) of the secondary air injection (AIR) system are stuck open. The engine control module (ECM) operates entire components of this system in a sequence, and monitors the system pressure and exhaust pulse (AIR monitor). This monitor will run just after a cold engine start. If abnormal pressure and exhaust pulse are detected, the ECM interprets this as a malfunction. When the malfunction is detected in consecutive driving cycles, the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.
A182943E01
Reference 1: Operation of each component during AIR monitor
A182941E01
Reference 2: DTC Storing Conditions 
Time A
[Pressure Change]
Time B
[Pressure Change]
Time C
[See Chart Below]
Time D
[Exhaust Pulse]
Time E
[Exhaust Pulse]
Time F
[See Chart Below]
DTC
Yes
Yes
Pattern 1
-
No
Pattern 4
Normal
Yes
No
Pattern 1
Yes
No
Pattern 4
Yes
Yes
Pattern 1
-
No
Pattern 1
P1441
P1444
P2444
No
Yes
Pattern 1
-
No
Pattern 1
Yes
No
Pattern 1
Yes
No
Pattern 1
No
No
Pattern 1
Yes
No
Pattern 1
Yes
Yes
Pattern 1
-
No
Pattern 2
P1441
P1444
No
Yes
Pattern 1
-
No
Pattern 2
Yes
No
Pattern 1
Yes
No
Pattern 2
No
No
Pattern 1
Yes
No
Pattern 2
-
-
-
-
Yes
-
P1441
P1444
P2444
Reference 3: System Pressure and Exhaust Pulse 
Pattern
System Pressure
Exhaust Pulse
1
High
Yes
2
Low
Yes
3
High
No
4
Low
No
DTC Code 
DTC Code
DTC Detection Condition
Trouble Area
P1441
The ASV (bank 1) is stuck open (2 trip detection logic).
  1. ASV (bank 1)
  2. VSV (bank 1)
P1444
The ASV (bank 2) is stuck open (2 trip detection logic).
  1. ASV (bank 2)
  2. VSV (bank 2)
P2440
The E-ASV is stuck open (2 trip detection logic).
  1. E-ASV
  2. ASV (bank 1 and/or bank 2)
  3. VSV (bank 1 and/or bank 2)

WIRING DIAGRAM

Refer to DTC P0412 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM SECONDARY AIR INJECTION SYSTEM CHECK (AUTOMATIC MODE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Record the DTCs and freeze frame data.

  1. Clear the DTCs (Click here).

  1. Warm-up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check (Automatic Mode).

  1. Perform the Active Test and check the pending DTC.

    Result 
    Result
    Proceed to
    P1441 and/or P1444 is output
    A
    P2440, P1441 and/or P1444 is output
    B
    DTCs other than P1441, P1444 and P2440 are output
    C
    No DTC is output
    D

    HINT:
    If any DTCs other than P1441, P1444 or P2440 are output, troubleshoot those DTCs first.



B
Go to step 3

C
GO TO DTC CHART (Click here)

D
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2. CHECK VACUUM SWITCHING VALVE

  1. A182942E01
    Disconnect the vacuum hoses connected to the Vacuum Switching Valve (VSV).

  1. Connect the vacuum pump to port A shown in the illustration.

  1. Operate the pump and check that there is no vacuum from the other port.

    OK:
    No vacuum.



NG
REPLACE VACUUM SWITCHING VALVE (Click here)
OK

REPLACE AIR SWITCHING VALVE (NO. 1 or NO. 2) (Click here)

3. CHECK VACUUM SWITCHING VALVE

  1. A182942E01
    Disconnect the vacuum hoses connected to the Vacuum Switching Valve (VSV).

  1. Connect the vacuum pump to port A shown in the illustration.

  1. Operate the pump and check that there is no vacuum from the other port.

    OK:
    No vacuum.



NG
REPLACE VACUUM SWITCHING VALVE (Click here)
OK


4. CHECK AIR SWITCHING VALVE (OPERATION)
  1. Remove the intake manifold (Click here).

  1. Remove the Air Switching Valve (ASV).

  1. G032728E01
    Blow air into port A and check that air is not discharged from port B.

  1. G032729E02
    Apply battery positive voltage across the terminals.

  1. Blow air into port A and check that air is discharged from port B.

    OK:
    Tester Connection
    Condition
    Specified Condition
    port A - port B
    Always
    Not discharged
    port A - port B
    Battery positive voltage applied
    Discharged



NG
REPLACE AIR SWITCHING VALVE ASSEMBLY (Click here)
OK

REPLACE AIR SWITCHING VALVE (NO. 1 or NO. 2) (Click here)


← P1440 Secondary Air Injection Vacuum Switching Valve Circuit Malfunction Bank 1 (+ P1443) (Sep 2011 – Dec 2011)P1442 Stuck Close in Secondary Air Injection Vacuum Switching Valve Bank 1 (+ P1445, P2441) (Sep 2011 – Dec 2011) →